AVSPARE.COM
parts catalog

MUFFLER AS 1608583 - Caterpillar


1608583 MUFFLER AS Caterpillar parts 966G, 972G
Rating:
47
Alternative (cross code) number:
CA1608583
160-8583
1608583
Caterpillar 1608583 MUFFLER AS
Weight: 64 pounds 29 kg.

Buy MUFFLER AS 1608583 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL LOADER,

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below
$273.01

07 Aug 2025
83.0[37.35] Pounds
Amazon.com
CTP 1608583 Muffler Assembly for Models 966G/972G
CTP For models 966G/972G || Sold in each || Easy in-and-out fit
$279.79

26 Jun 2025
83.0[37.35] pounds
Amazon.com
CTP 1608583 Muffler Assembly for Models 966G/972G
CTP For models 966G/972G || Sold in each || Easy in-and-out fit
$272.80

19 Apr 2025
83.0[37.35] pounds
Amazon.com
CTP 1608583 Muffler Assembly for Models 966G/972G
CTP For models 966G/972G || Sold in each || Easy in-and-out fit
Number on catalog scheme: 3
  For full view, you need register

Compatible equipment models: 1608583:

WHEEL LOADER  966G   972G   Caterpillar

Information:


Illustration 1 g00595836
Schematic For Pressure Sensor (Engine Oil)The EMCP II monitors the engine oil pressure in order to protect the engine in case of a problem with the oil pressure. The pressure sensor is usually mounted on an oil gallery of the engine. The exact location of the engine oil pressure sensor depends on the engine model.The sensor is powered by an 8 volt sensor supply from the GSC. The oil pressure signal is a pulse width modulated signal. The base frequency of the signal is 500 150 Hz. As pressure changes, the duty cycle of the signal varies from 10% to 95%. A pressure of 0 kPa (0 psi) is approximately 13% of the duty cycle. A pressure of 690 kPa (100 psi) is approximately 85% of the duty cycle.Note: The GSC is usually programmed to treat a diagnostic code with the pressure sensor as an alarm fault (P04 = 0). If the GSC is programmed to treat a fault with the pressure sensor as a shutdown fault (P04 = 1), then diagnostic codes are automatically shown on the upper display.Note: Faults are created when the harness connector (40 contact) is disconnected from the GSC during these troubleshooting procedures. Clear these created faults after the particular fault is corrected. In a properly operating system, when the harness connector is removed from the GSC, the following diagnostic codes are recorded.
CID 100 FMI 3 pressure sensor (engine oil)
CID 110 FMI 3 temperature sensor (engine coolant)
CID 111 FMI 3 fluid level sensor (engine coolant)
CID 190 FMI 3 speed sensor (engine)
CID 331 FMI 2 switch (engine control)
CID 336 FMI 2 switch (engine control)ProcedureThis diagnostic code can be caused by the following condition:
There is a short to the -battery of the sensor signal.Begin performing these procedures only when CID 100 FMI 4 is showing and the "DIAG" indicator is FLASHING on the upper display. The GSC treats a CID 100 FMI 4 as an alarm fault. Active alarm faults are shown on the display when the alarm codes key is pressed and the ECS is in any position except the OFF/RESET position. For an inactive fault, the problem may be intermittent. To troubleshoot an inactive fault, use the preceding system schematic and see Testing And Adjusting, "Electrical Connector - Inspect". Clear the diagnostic code from the fault log after troubleshooting is complete.Note: If CID 269 is active, then correct the diagnostic code prior to proceeding with this procedure.
Check the GSC and the harness.
Ensure that CID 100 FMI 4 is showing on the display.
Turn the ECS to the "OFF/RESET" position.
Disconnect the sensor from the engine harness. The sensor should remain fastened to the engine.
Turn the ECS to the "STOP" position.
Press the alarm codes key. This is not required for shutdown faults.
Verify that CID 100 FMI 04 is no longer showing and verify that CID 100 FMI 03 is now showing.Expected Result: CID 100 FMI 4 is not showing. CID 100 FMI 3 is now showing.Results:
OK - The GSC and the harness function properly.

Caterpillar parts catalog:

Caterpillar parts catalog
966G Wheel Loader 3ZS00001-UP (MACHINE) POWERED BY 3306 Engine
972G Wheel Loader 7LS00001-UP (MACHINE) POWERED BY 3306 Engine
966G Wheel Loader 9RS00001-UP (MACHINE) POWERED BY 3306 Engine
972G Wheel Loader 1EW00001-UP (MACHINE) POWERED BY 3306 Engine
966G Wheel Loader 3SW00001-UP (MACHINE) POWERED BY 3306 Engine
972G Wheel Loader 4WW00001-UP (MACHINE) POWERED BY 3306 Engine
966G Wheel Loader 3PW00001-UP (MACHINE) POWERED BY 3306 Engine
972G Wheel Loader 6AW00001-UP (MACHINE) POWERED BY 3306 Engine
966G Wheel Loader HDH00001-UP (MACHINE) POWERED BY 3306 Engine


Parts muffler Caterpillar catalog:

1224990 MUFFLER AS
844, 990, 990 II
1224989 MUFFLER AS
844, 990, 990 II
1666670 MUFFLER AS
824C, 824G, 825G, 826G, 980G
2233646 MUFFLER AS
966G II, 972G II
1335927 MUFFLER AS
994D, 994F, 994H
1299459 MUFFLER AS
994D, 994F, 994H
2397897 MUFFLER AS
834G, 836G, 988G, RM-500
1326199 MUFFLER AS
834G, 836G, 988G
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.