1630451 MUFFLER AS Caterpillar parts
65E, 75E, 85E, 95E
Rating:
Alternative (cross code) number:
CA1630451
163-0451
1630451
CA1630451
163-0451
1630451
Weight: 77 pounds 35 kg.
Information:
BODY DIAMETER/WIDTH
374.6
mm
BODY LENGTH
1361.2
mm
INLET ID
127.64
mm
OUTLET OD
127
mm
OVAL HEIGHT
0
mm
OVERALL LENGTH
1505
mm
PROTECTIVE SHIELD
N
WITH EJECTOR
N
WITH MOUNTING BRACKET
N
WITH OUTER WRAP
N
CHALLENGER,
This part in 10 request:
Show.
This information for suppliers only!
2022-03-09
2021-08-17
2021-05-13
2020-04-14
2020-04-14
2019-12-17
2019-09-09
2017-06-06
2017-06-06
2016-07-26
Number on catalog scheme:
1
For full view, you need register
Information:
Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01347869
Typical example
Follow Steps 1.a through 1.d in order to assemble the engine oil cooler.
Ensure that cooler matrix (3) is clean and free from damage. Ensure that housing (5) is clean and free from damage.
Position new joints (4) onto housing (5). Install cooler matrix (3).
Apply Tooling (A) to the threads of bolts (6).
Install bolts (6). Tighten the bolts to a torque of 22 N m (16 lb ft).
Clean the mating surface of the cylinder block.
Illustration 2 g01347870
Typical example
Position a new joint (2) on the assembly of engine oil cooler (1). Install fasteners (7) to positions (X) on the assembly of engine oil cooler (1). Note: The holes in the joint have serrations that hold the fasteners captive.
Install the assembly of engine oil cooler (1) to the cylinder block. Tighten bolts (7) finger tight. Note: The fasteners are different lengths. Ensure that the different fasteners are installed in the correct location. Ensure that any brackets that are secured by the fasteners are installed in the correct location.
Apply Tooling (B) to the fasteners (7) at positions (Y). Note: The fasteners in this position are allen head screws.
Illustration 3 g01343558
Tightening sequence for the engine oil cooler
Install the remaining fasteners (7) into the engine oil cooler (1). Tighten the fasteners to a torque of 22 N m (16 lb ft). Tighten the bolts in the sequence that is shown in Illustration 3.
If necessary, Install the Electronic Control Module (ECM). Refer to Disassembly and Assembly, "Electronic Control Module - Remove and Install" for the correct procedure.
If necessary, Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install" for the correct procedure.
Fill the cooling system to the correct level. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the correct procedure.
Fill the engine oil pan to the correct level. Refer to Operation and Maintenance Manual, "Engine Oil Filter and Change" for the correct procedure.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01347869
Typical example
Follow Steps 1.a through 1.d in order to assemble the engine oil cooler.
Ensure that cooler matrix (3) is clean and free from damage. Ensure that housing (5) is clean and free from damage.
Position new joints (4) onto housing (5). Install cooler matrix (3).
Apply Tooling (A) to the threads of bolts (6).
Install bolts (6). Tighten the bolts to a torque of 22 N m (16 lb ft).
Clean the mating surface of the cylinder block.
Illustration 2 g01347870
Typical example
Position a new joint (2) on the assembly of engine oil cooler (1). Install fasteners (7) to positions (X) on the assembly of engine oil cooler (1). Note: The holes in the joint have serrations that hold the fasteners captive.
Install the assembly of engine oil cooler (1) to the cylinder block. Tighten bolts (7) finger tight. Note: The fasteners are different lengths. Ensure that the different fasteners are installed in the correct location. Ensure that any brackets that are secured by the fasteners are installed in the correct location.
Apply Tooling (B) to the fasteners (7) at positions (Y). Note: The fasteners in this position are allen head screws.
Illustration 3 g01343558
Tightening sequence for the engine oil cooler
Install the remaining fasteners (7) into the engine oil cooler (1). Tighten the fasteners to a torque of 22 N m (16 lb ft). Tighten the bolts in the sequence that is shown in Illustration 3.
If necessary, Install the Electronic Control Module (ECM). Refer to Disassembly and Assembly, "Electronic Control Module - Remove and Install" for the correct procedure.
If necessary, Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor - Remove and Install" for the correct procedure.
Fill the cooling system to the correct level. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the correct procedure.
Fill the engine oil pan to the correct level. Refer to Operation and Maintenance Manual, "Engine Oil Filter and Change" for the correct procedure.
Caterpillar parts catalog:
Parts muffler Caterpillar catalog:
1365109
MUFFLER GP
65E, 75E, 85E, 95E
65E, 75E, 85E, 95E
1690016
MUFFLER GP
65E, 75E, 85E, 95E
65E, 75E, 85E, 95E
1365108
MUFFLER AS
65E, 75E, 85E, 95E
65E, 75E, 85E, 95E
1541889
MUFFLER AS
416C, 426C, 428C, 436C, 438C
416C, 426C, 428C, 436C, 438C
416C, 416D, 420D, 426C, 428C, 428D, 430D, 432D, 436C, 438C, 438D, 442D
1582885
MUFFLER AS
416C, 428C
416C, 428C
416C, 416D, 424D, 428C
416B, 426B, 428B, 438B, CP-433C, CS-323C, CS-431C
1979717
MUFFLER
TH103, TH62, TH63, TH82, TH83
TH103, TH62, TH63, TH82, TH83
1922613
MUFFLER GP
236, 267
236, 267
414E, 416D, 416E, 422E, 424D
1428820
MUFFLER AS
236, 248
236, 248
1365108
MUFFLER AS
65E, 75E, 85E, 95E
65E, 75E, 85E, 95E