1917556 MUFFLER AS Caterpillar parts
304, 305
Rating:
Alternative (cross code) number:
CA1917556
191-7556
1917556
CA1917556
191-7556
1917556
Weight: 12 pounds 5 kg.
Information:
BODY DIAMETER/WIDTH
200
mm
BODY LENGTH
300
mm
INLET ID
42.7
mm
OUTLET OD
42.7
mm
OVAL HEIGHT
0
mm
OVERALL LENGTH
364
mm
PROTECTIVE SHIELD
N
WITH EJECTOR
N
WITH MOUNTING BRACKET
N
WITH OUTER WRAP
N
MINI HYD EXCAVATOR,
This part in 2 request:
Show.
This information for suppliers only!
2024-02-25
2016-06-07
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 132-8223 110 volt Power Pack 1
1U-6221 Torque Wrench 1
132-8143 36 mm Hex Link 1
B 138-7573 Link Bracket 4
D 5P-3931 Anti-Seize Compound 1
E 1U-8846 Gasket Sealant 1
Thoroughly clean the mating surfaces of the swing drive housing and the main frame.
Apply Tooling (D) on the locating pin in the main frame. Also, apply Tooling (D) in the pin bore in the main frame.
Apply Tooling (E) on the mating surface of the main frame and the swing drive housing.
Illustration 1 g00875735Note: During installation, the locating pin for the swing drive can come out of the swing drive housing.
Attach Tooling (B) and a suitable lifting device to swing drive (2). The weight of swing drive (2) is approximately 510 kg (1125 lb). Place swing drive (2) in the swing drive's original position in the main frame. If the locating pin comes out of the swing drive housing, the locating pin can be reinstalled with a hammer after the swing drive is in place.
Illustration 2 g00875734
Use Tooling (A) to install new bolts (3) that secure the swing drive to the main frame. Tighten bolts (3) to a torque of 900 100 N m (664 74 lb ft).
Illustration 3 g00875732
Close drain valve (1). Fill swing drive (2). Refer to Operation and Maintenance Manual, "Swing Drive Oil - Change". End By:
Install the swing motor. Refer to Disassembly and Assembly, "Swing Motor - Install".
Table 1
Required Tools
Tool Part Number Part Description Qty
A 132-8223 110 volt Power Pack 1
1U-6221 Torque Wrench 1
132-8143 36 mm Hex Link 1
B 138-7573 Link Bracket 4
D 5P-3931 Anti-Seize Compound 1
E 1U-8846 Gasket Sealant 1
Thoroughly clean the mating surfaces of the swing drive housing and the main frame.
Apply Tooling (D) on the locating pin in the main frame. Also, apply Tooling (D) in the pin bore in the main frame.
Apply Tooling (E) on the mating surface of the main frame and the swing drive housing.
Illustration 1 g00875735Note: During installation, the locating pin for the swing drive can come out of the swing drive housing.
Attach Tooling (B) and a suitable lifting device to swing drive (2). The weight of swing drive (2) is approximately 510 kg (1125 lb). Place swing drive (2) in the swing drive's original position in the main frame. If the locating pin comes out of the swing drive housing, the locating pin can be reinstalled with a hammer after the swing drive is in place.
Illustration 2 g00875734
Use Tooling (A) to install new bolts (3) that secure the swing drive to the main frame. Tighten bolts (3) to a torque of 900 100 N m (664 74 lb ft).
Illustration 3 g00875732
Close drain valve (1). Fill swing drive (2). Refer to Operation and Maintenance Manual, "Swing Drive Oil - Change". End By:
Install the swing motor. Refer to Disassembly and Assembly, "Swing Motor - Install".
Caterpillar parts catalog:
Parts muffler Caterpillar catalog:
2165589
MUFFLER GP
304, 305
304, 305
2159487
MUFFLER
M313C
M313C
1977911
MUFFLER
M315C, M316C, M318C, M318C MH, M322C
M315C, M316C, M318C, M318C MH, M322C
2128507
MUFFLER
311C, 312C L
311C, 312C L
1905781
MUFFLER
305.5, 306, 307C, 307D, 308C, 308D
305.5, 306, 307C, 307D, 308C, 308D
1710475
MUFFLER AS
304.5
304.5
1710696
MUFFLER AS
303.5
303.5
2666173
MUFFLER AS
315C
315C
2056785
MUFFLER AS
315C
315C
2666251
MUFFLER
318C, 319C, 320C, 320C FM, 320C L
318C, 319C, 320C, 320C FM, 320C L
2128633
MUFFLER
314C
314C
2128491
MUFFLER
311C, 311D LRR, 312C, 312C L, 312D, 312D L, 313D, 314D CR, 314D LCR
311C, 311D LRR, 312C, 312C L, 312D, 312D L, 313D, 314D CR, 314D LCR