2126961 MUFFLER AS Caterpillar parts
140H
Rating:
Alternative (cross code) number:
CA2126961
212-6961
2126961
CA2126961
212-6961
2126961
Weight: 45 pounds 20 kg.
MOTOR GRADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$241.46
27 Oct 2018
6300 Hundredths Pounds
COSTEX: COSTEX
New Aftermarket MUFFLER 2126961, 212-6961 Model# 140H, 160H
MUFFLERS
MUFFLERS
Compatible equipment models: 2126961:
Information:
Your engine may not have the same gauges or all of the gauges that are described. For more information about the gauge package, see the OEM information.Gauges provide indications of engine performance. Ensure that the gauges are in good working order. Determine the normal operating range by observing the gauges over a period.Noticeable changes in gauge readings indicate potential gauge or engine problems. Problems may also be indicated by gauge readings that change even if the readings are within specifications. Determine and correct the cause of any significant change in the readings. Consult your Caterpillar dealer for assistance.Some engine applications are equipped with Indicator Lamps. Indicator lamps can be used as a diagnostic aid. There are two lamps. One lamp has an orange lens and the other lamp has a red lens.These indicator lamps can be used in two ways:
The indicator lamps can be used to identify the current operational status of the engine. The indicator lamps can also indicate that the engine has a fault. This system is automatically operated via the ignition switch.
The indicator lamps can be used to identify active diagnostic codes. This system is activated by pressing the Flash Code button.Refer to the Troubleshooting Guide, "Indicator Lamps" for further information.
If no oil pressure is indicated, STOP the engine. If maximum coolant temperature is exceeded, STOP the engine. Engine damage can result.
Engine Oil Pressure - The oil pressure should be greatest after a cold engine is started. The typical engine oil pressure with SAE10W40 is 400 to 480 kPa (58 to 69 psi) at rated rpm.A lower oil pressure is normal at low idle. If the load is stable and the gauge reading changes, perform the following procedure:
Remove the load.
Stop the engine.
Check and maintain the oil level.
Jacket Water Coolant Temperature - Typical temperature range is 82° to 94°C (179.6° to 169.2°F). This temperature range will vary according to engine load and the ambient temperature. A 100 kPa (14.5 psi) radiator cap must be installed on the cooling system. The maximum temperature for the cooling system is 108° C (226.4° F). The engine coolant temperature is regulated by the engine sensors and the engine ECM. This programming cannot be altered. An engine derate can occur if the maximum engine coolant temperature is exceeded.If the engine is operating above the normal range, reduce the engine load. If high coolant temperatures are a frequent event, perform the following procedures:
Reduce the load and the engine rpm.
Determine if the engine must be shut down immediately or if the engine can be cooled by reducing the load.
Inspect the cooling system for leaks. If necessary, consult your Caterpillar dealer for assistance.
Tachometer - This gauge indicates engine speed (rpm). When the throttle control lever is moved to the full throttle position without load, the engine is running at high idle. The engine is running at the full load rpm when the throttle control lever is at the full throttle position with maximum rated load.
To help prevent engine damage, never exceed the high idle
The indicator lamps can be used to identify the current operational status of the engine. The indicator lamps can also indicate that the engine has a fault. This system is automatically operated via the ignition switch.
The indicator lamps can be used to identify active diagnostic codes. This system is activated by pressing the Flash Code button.Refer to the Troubleshooting Guide, "Indicator Lamps" for further information.
If no oil pressure is indicated, STOP the engine. If maximum coolant temperature is exceeded, STOP the engine. Engine damage can result.
Engine Oil Pressure - The oil pressure should be greatest after a cold engine is started. The typical engine oil pressure with SAE10W40 is 400 to 480 kPa (58 to 69 psi) at rated rpm.A lower oil pressure is normal at low idle. If the load is stable and the gauge reading changes, perform the following procedure:
Remove the load.
Stop the engine.
Check and maintain the oil level.
Jacket Water Coolant Temperature - Typical temperature range is 82° to 94°C (179.6° to 169.2°F). This temperature range will vary according to engine load and the ambient temperature. A 100 kPa (14.5 psi) radiator cap must be installed on the cooling system. The maximum temperature for the cooling system is 108° C (226.4° F). The engine coolant temperature is regulated by the engine sensors and the engine ECM. This programming cannot be altered. An engine derate can occur if the maximum engine coolant temperature is exceeded.If the engine is operating above the normal range, reduce the engine load. If high coolant temperatures are a frequent event, perform the following procedures:
Reduce the load and the engine rpm.
Determine if the engine must be shut down immediately or if the engine can be cooled by reducing the load.
Inspect the cooling system for leaks. If necessary, consult your Caterpillar dealer for assistance.
Tachometer - This gauge indicates engine speed (rpm). When the throttle control lever is moved to the full throttle position without load, the engine is running at high idle. The engine is running at the full load rpm when the throttle control lever is at the full throttle position with maximum rated load.
To help prevent engine damage, never exceed the high idle
Caterpillar parts catalog:
Parts muffler Caterpillar catalog:
1597368
MUFFLER & MOUNTING GP
140H, 143H, 14H, 160H, 163H
140H, 143H, 14H, 160H, 163H
2010346
MUFFLER AS
120H, 12H, 135H
120H, 12H, 135H
3053795
MUFFLER AS
140H, 143H, 14H, 160H, 163H, 16H
140H, 143H, 14H, 160H, 163H, 16H
7E7984
MUFFLER AS
140H, 160H
140H, 160H
4P6649
MUFFLER AS
16H NA
16H NA
2666269
MUFFLER AS
330D, 330D L, 330D LN, 336D2, M330D
330D, 330D L, 330D LN, 336D2, M330D
3521486
MUFFLER AS
12M, 140M
12M, 140M
2997985
MUFFLER AS
140M
140M
3016865
MUFFLER
120M, 12M
120M, 12M
2986551
MUFFLER AS
140M, 160M
140M, 160M