MUFFLER 2870205 - Caterpillar

2870205 MUFFLER Caterpillar parts 317B LN, 318B

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA2870205
287-0205
2870205

Weight: 27 pounds 12 kg.

Information:

BODY DIAMETER/WIDTH 252.4 mm

BODY LENGTH 645 mm

INLET ID 0 mm

OUTLET OD 90 mm

OVAL HEIGHT 0 mm

OVERALL LENGTH 645 mm

PROTECTIVE SHIELD N

WITH EJECTOR N

WITH MOUNTING BRACKET N

WITH OUTER WRAP N

Buy MUFFLER 2870205 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR,

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

WIDIA 2870205 Hanita VariMill I Inch End Mill 1.0000 Inch Dia, 1.5000 Inch Max Depth, 4.0000" Length, Weldon Shank Cylindrical Carbide TiAlN 4 Flutes TF4V0525008S

$427.48

22 May 2025

US: Consumer Supply

WIDIA 2870205 Hanita VariMill I Inch End Mill 1.0000 Inch Dia, 1.5000 Inch Max Depth, 4.0000" Length, Weldon Shank Cylindrical Carbide TiAlN 4 Flutes TF4V0525008S
WIDIA WIDIA 2870205 Hanita VariMill I Inch End Mill 1.0000 Inch Dia, 1.5000 Inch Max Depth, 4.0000" Length, Weldon Shank Cylindrical Carbide TiAlN 4 Flutes || ENDMILL 4V05 1X1X1.1/2X4 || When you buy WIDIA products, you are buying the ultimate in performance and tool life.

$365.34

14 Nov 2024

US: Consumer Supply

$271.03

21 Jun 2024

Amazon.com

Number on catalog scheme: 6

Caterpillar 2870205 Parts scheme MUFFLER

For full view, you need register

Compatible equipment models: 2870205:

EXCAVATOR 317B LN 318B Caterpillar

Information:

4634-3(2) Accessory Power Inverter Start-up Fault
This fault is likely the result of older machine software on the Machine ECM. The paver should be updated with all the latest software as per the Special Instructions, SEHS0522. Clear all logged faults from the paver. If this fault returns, a DSN should be submitted with a Product Status Report showing the logged fault and current software configuration.4632-6(2), 1095-6(2), or 4388-14(2) Fan Overcurrent Faults
These faults indicate that the fan is drawing more power than the Accessory Power Inverter is expecting. The exact fault code varies with the version of software that is on the machine ECM. All software should be updated with all the latest software as per the Special Instructions, SEHS0522.Follow the instruction below to add 508-9365 Resistor Assembly to the Fan Circuit.Note: New Accessory Power Converters with part numbers of 506-9431, 506-9432 or 506-9433 contain internal changes that do not require and will not benefit from the addition of 508-9365 Resistor Assembly. Adding the Resistor Assembly to these newer Accessory Power Converters is not recommended. The part number can be found near the outlets and is accessed through the outlet access door.Follow the Electrical Shutdown and Voltage Discharge procedure in UENR3864 before performing any procedures.Installation Procedure
Table 1
Required Parts List
Qty Part Number Description
1 508-9365 Harness
2 3S-2093 Strap-Cable
Illustration 1 g06089849
Remove the 10 screws indicated using a T-20 drive tool.
Tip the fan down to expose the fan's electrical connection to the Accessory Power Inverter. Cut and remove the cable tie used to secure the 2-pin connector to the existing harnesses. Disconnect the electrical connector.
Illustration 2 g06089855
Install Resistor Assembly, 508-9365, to the cooling fins of the inverter as indicated in the photo. Connect the connector lead from the fan to the left connector on the resistor assembly. Connect the right side of the resistor assembly to the Accessory Power Inverter.
Illustration 3 g06089872
Arrange wires and connectors to prevent rubbing on sharp surfaces, and secure with the tie strap, 3S-2093, as shown. Additional straps can be used if needed.
Reinstall the 10 screws holing the fan in place. Torque to 2.3 N m (20 lb in).Note: Make sure that excess wire is tied back.