MUFFLER GP 3106472 - Caterpillar

Illustration 8 g00480251
112-9577 Hub Assembly Heat guard (V) to 175°C (350°F) and press fitting onto the spindle. Do not weld.Modification to Existing Parts of D5M and D5N
Illustration 9 g00482621
5Q-7554 Hub (A) 5 1 degrees (B) Diameter 280.00 0.25 mm (11.024 0.010 inch) (C) Diameter 286.00 0.25 mm (11.260 0.010 inch) (D) Diameter 290.0 0.1 mm (11.417 0.004 inch) (E) 15 1 degrees (F) 15.0 0.25 mm (0.59 0.010 inch) (G) 35.50 0.25 mm (1.398 0.010 inch) (H) 54.50 0.25 mm (2.146 0.010 inch) (J) 30 1 degrees (K) Radius 2.00 0.25 mm (0.079 0.010 inch)Machine the 106-0701 Hub according to the dimensions that are shown.
Illustration 10 g00482631
5Q-7555 Spindle (N) 35.85 0.25 mm (1.41 0.010 inch) (P) Radius 2.00 0.25 mm (0.079 0.010 inch) (R) Diameter 267.0 0.1 mm (10.512 0.004 inch)Machine the 135-6150 Spindle according to the dimensions that are shown.
Illustration 11 g00482637
5Q-7556 Spindle Assembly Heat guard (U) to 120°C (250°F) and press fitting onto the spindle.Preheat guard (U) to 120°C (250°F). Make a fillet weld all the way around the guard at location (T) of 5 mm (0.2 inch).
Illustration 12 g00482639
5Q-7538 Hub Assembly Heat guard (V) to 175°C (350°F) and press fitting onto the spindle. Do not weld.Modification to Existing Parts of D6M and D6N
Illustration 13 g00480104
5Q-7579 Hub (A) 10 1 degrees (B) Diameter 262.00 0.25 mm (10.315 0.010 inch) (C) Diameter 276.00 0.25 mm (10.866 0.010 inch) (D) Diameter 280.0 0.1 mm (11.024 0.004 inch) (E) 15 1 degrees (F) 15.0 0.5 mm (0.59 0.02 inch) (G) 31.50 0.25 mm (1.240 0.010 inch) (H) 50.50 0.25 mm (1.988 0.010 inch) (J) 30 1 degrees (K) Radius 2.00 0.25 mm (0.079 0.010 inch)Machine the 107-1763 Hub according to the dimensions that are shown.
Illustration 14 g00480155
104-1965 Spindle (N) 25.86 0.25 mm (1.018 0.010 inch) (P) Radius 2.00 0.25 mm (0.079 0.010 inch) (R) Diameter 267.0 0.1 mm (10.512 0.004 inch)Machine the 135-6156 Spindle according to the dimensions that are shown.
Illustration 15 g00480216
104-1964 Spindle Assembly Heat guard (U) to 120°C (250°F) and press fitting onto the spindle.Preheat the Guard (U) to 120°C (250°F). Make a fillet weld all the way around the guard at location (T) of 5 mm (0.2 inch).
Illustration 16 g00480251
5Q-7578 Hub Assembly Heat guard (V) to 175°C (350°F) and press fitting onto the spindle. Do not weld.Installation
Reassemble the final drive according to the instructions in the Service Manual.Note: Refer to Special Instruction, SEHS8364 before installing the Duo-Cone Seals.Install the final drive on the machine according to the instructions in the Service Manual.