4P4010 MUFFLER AS Caterpillar parts
215B
Rating:
Alternative (cross code) number:
CA4P4010
4P-4010
4P4010
CA4P4010
4P-4010
4P4010
Weight: 33 pounds 14 kg.
Information:
BODY DIAMETER/WIDTH
225.6
mm
BODY LENGTH
513
mm
INLET ID
102.39
mm
OUTLET OD
92.13
mm
OVAL HEIGHT
307.8
mm
OVERALL LENGTH
647.2
mm
PROTECTIVE SHIELD
N
WITH EJECTOR
N
WITH MOUNTING BRACKET
N
WITH OUTER WRAP
Y
EXCAVATOR,
Related part:
4P4010
MUFFLER-AS-YM
2982788
CL
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
CTP 4P4010 Muffler for Models 215/215B/215C/215D/219/219D
CTP For models 215/215B/215C/215D/219/219D || Sold in each || Easy in-and-out fit
CTP For models 215/215B/215C/215D/219/219D || Sold in each || Easy in-and-out fit
CTP 4P4010 Muffler for Models 215/215B/215C/215D/219/219D
CTP For models 215/215B/215C/215D/219/219D || Sold in each || Easy in-and-out fit
CTP For models 215/215B/215C/215D/219/219D || Sold in each || Easy in-and-out fit
Number on catalog scheme:
5
For full view, you need register
Compatible equipment models: 4P4010:
Information:
Removal Procedure
Start By:
Remove the valve cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Release and Install".Note: Put identification marks on all hoses, on all hose assemblies, on all wires, and on all tube assemblies for installation purposes. Plug all hose assemblies and all tube assemblies. This helps to prevent fluid loss, and this helps to keep contaminants from entering the system.Note: Cleanliness is an important factor. Before you begin the removal procedure, the exterior of the components should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01267071
Disconnect harness assembly (1). Remove engine oil pressure sensor (2) .Installation Procedure
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning fluid. Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be deposited on the parts which may cause trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement. Dirt and other contaminants can damage the precision component. Perform assembly procedures on a clean work surface. Keep components covered and protected at all times.Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the components, if necessary.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Illustration 2 g01267071
Install engine oil pressure sensor (2). Tighten engine oil pressure sensor (2) to a torque of 20 3 N m (15 2 lb ft). Connect harness assembly (1) .End By: Install the valve cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Release and Install".
Start By:
Remove the valve cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Release and Install".Note: Put identification marks on all hoses, on all hose assemblies, on all wires, and on all tube assemblies for installation purposes. Plug all hose assemblies and all tube assemblies. This helps to prevent fluid loss, and this helps to keep contaminants from entering the system.Note: Cleanliness is an important factor. Before you begin the removal procedure, the exterior of the components should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01267071
Disconnect harness assembly (1). Remove engine oil pressure sensor (2) .Installation Procedure
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning fluid. Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be deposited on the parts which may cause trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement. Dirt and other contaminants can damage the precision component. Perform assembly procedures on a clean work surface. Keep components covered and protected at all times.Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the components, if necessary.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Illustration 2 g01267071
Install engine oil pressure sensor (2). Tighten engine oil pressure sensor (2) to a torque of 20 3 N m (15 2 lb ft). Connect harness assembly (1) .End By: Install the valve cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover - Release and Install".
Caterpillar parts catalog:
Parts muffler Caterpillar catalog:
6C1228
MUFFLER GP
215B, 215C, 215D, 219D
215B, 215C, 215D, 219D
6C0359
MUFFLER GP
215, 215B
215, 215B
245B
245B
7E5663
MUFFLER AS
225D, 231D, AP-655C
225D, 231D, AP-655C
235B, 235C
311
307, E70B
311
311, 311B, 312B
5W4262
MUFFLER GP-EXHA
205, 206, 212
205, 206, 212