6N5437 MUFFLER AS Caterpillar parts
Rating:
Alternative (cross code) number:
CA6N5437
6N-5437
6N5437
CA6N5437
6N-5437
6N5437
Weight: 44 pounds 19 kg.
Information:
BODY DIAMETER/WIDTH
209.6
mm
BODY LENGTH
558.8
mm
INLET ID
127.97
mm
OUTLET OD
130.8
mm
OVAL HEIGHT
292.1
mm
OVERALL LENGTH
895.6
mm
PROTECTIVE SHIELD
N
WITH EJECTOR
Y
WITH MOUNTING BRACKET
Y
WITH OUTER WRAP
Y
Related part:
6N5437
MUFFLER-AS-YM
2472674
CL
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
CTP 6N5437 Muffler for Model D8K
CTP For model D8K || Sold in each || Easy in-and-out fit
CTP For model D8K || Sold in each || Easy in-and-out fit
CTP 6N5437 Muffler for Model D8K
CTP For model D8K || Sold in each || Easy in-and-out fit
CTP For model D8K || Sold in each || Easy in-and-out fit
Information:
Removal Procedure
Start By:
Remove the crankshaft rear seal. Refer to Disassembly and Assembly Manual, "Crankshaft Rear Seal - Remove" for the correct procedure.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Wear sleeves are used to reclaim worn seal surfaces or damaged seal surfaces. Wear sleeves are not original equipment.
Illustration 1 g03358286
Use a sharp tool to score a deep line across the crankshaft wear sleeve (1). Note: Take care to avoid damaging the crankshaft.
Insert a thin blade between crankshaft wear sleeve (1) and crankshaft (2) below the scored line. The crankshaft wear sleeve will separate along the line.
Remove crankshaft wear sleeve (1) from crankshaft (2). Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description
A 1U-8846 Liquid Gasket
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that the crankshaft is thoroughly clean and dry.
Illustration 2 g03358287
Apply a small continuous bead of Tooling (A) to the inner surface of a new crankshaft wear sleeve (1) at Position X. Apply the bead of Tooling (A) 5 mm (0.2 inch) from the flange end of crankshaft wear sleeve.
Illustration 3 g03338321
Align crankshaft wear sleeve (1) with crankshaft (2). Position installation tool (3) that is provided with the crankshaft wear sleeve over the crankshaft. Use a hammer to drive the crankshaft wear sleeve onto the crankshaft. Ensure that the flange of the crankshaft wear sleeve is 0.40 to 0.60 mm (0.017 to 0.024 inch) from the cylinder block. Note: Measure Distance (Y) between the flange of crankshaft wear sleeve (1) and the cylinder block in two places that are 180 degrees from each other.
Remove installation tool (3).
Ensure that the crankshaft wear sleeve has no rough edges. End By:
Install a new crankshaft rear seal. Refer to Disassembly and Assembly Manual, "Crankshaft Rear Seal - Install" for the correct procedure.
Start By:
Remove the crankshaft rear seal. Refer to Disassembly and Assembly Manual, "Crankshaft Rear Seal - Remove" for the correct procedure.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Wear sleeves are used to reclaim worn seal surfaces or damaged seal surfaces. Wear sleeves are not original equipment.
Illustration 1 g03358286
Use a sharp tool to score a deep line across the crankshaft wear sleeve (1). Note: Take care to avoid damaging the crankshaft.
Insert a thin blade between crankshaft wear sleeve (1) and crankshaft (2) below the scored line. The crankshaft wear sleeve will separate along the line.
Remove crankshaft wear sleeve (1) from crankshaft (2). Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description
A 1U-8846 Liquid Gasket
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that the crankshaft is thoroughly clean and dry.
Illustration 2 g03358287
Apply a small continuous bead of Tooling (A) to the inner surface of a new crankshaft wear sleeve (1) at Position X. Apply the bead of Tooling (A) 5 mm (0.2 inch) from the flange end of crankshaft wear sleeve.
Illustration 3 g03338321
Align crankshaft wear sleeve (1) with crankshaft (2). Position installation tool (3) that is provided with the crankshaft wear sleeve over the crankshaft. Use a hammer to drive the crankshaft wear sleeve onto the crankshaft. Ensure that the flange of the crankshaft wear sleeve is 0.40 to 0.60 mm (0.017 to 0.024 inch) from the cylinder block. Note: Measure Distance (Y) between the flange of crankshaft wear sleeve (1) and the cylinder block in two places that are 180 degrees from each other.
Remove installation tool (3).
Ensure that the crankshaft wear sleeve has no rough edges. End By:
Install a new crankshaft rear seal. Refer to Disassembly and Assembly Manual, "Crankshaft Rear Seal - Install" for the correct procedure.
Caterpillar parts catalog:
Parts muffler Caterpillar catalog:
5430758
MUFFLER GP
Caterpillar
Caterpillar
4916057
MUFFLER AS
Caterpillar
Caterpillar
4904857
MUFFLER GP
Caterpillar
Caterpillar
4904856
MUFFLER GP
Caterpillar
Caterpillar
4786537
MUFFLER GP
Caterpillar
Caterpillar
4674842
MUFFLER AS
Caterpillar
Caterpillar
4872901
MUFFLER AS
Caterpillar
Caterpillar
4844314
MUFFLER & MOUNTING GP
Caterpillar
Caterpillar
4588302
MUFFLER AS
Caterpillar
Caterpillar
3903998
MUFFLER GP
Caterpillar
Caterpillar
3650089
MUFFLER GP
Caterpillar
Caterpillar
2472675
MUFFLER
Caterpillar
Caterpillar