AVSPARE.COM
parts catalog

NET, RIGHT UNDER SIDE 0878481 - Caterpillar



0878481 NET, RIGHT UNDER SIDE Caterpillar parts EL240B NET
Rating:
84
Alternative (cross code) number:
CA0878481
087-8481
0878481
Caterpillar 0878481 NET, RIGHT UNDER SIDE
Weight: 3 pounds 1 kg.

Buy NET, RIGHT UNDER SIDE 0878481 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR,

Compatible equipment models: 0878481:

EXCAVATOR  EL240B   Caterpillar
Number on catalog scheme: 26
 
  For full view, you need register

Information:


Illustration 3 g02156033
Tooling group (D)
Table 3
Required Tools
Tool Item Part
Number Description Qty
B 198-4240 Digital Pressure Indicator Gp
B1 198-4234 Indicator 1
B2 198-4237 Pressure Sensor
34,450 kPa (5,000 psi) 1
B3 198-4236 Extension Cable 1
C 348-5430 Multi-Tool Gp 1
C1 285-0908 Multi-Tool 1
C2 6V-2198 Cable As 1
C3 9U-5140 Photo Pickup 1
C4 6V-3137 Base 1
C5 1U-6605 Reflective Tape 1
C6 6V-3138 Extension 1
D D1 6V-7788 Flow Meter
5 to 60 L/min (2 to 15 US gpm) 1
D2 8C-6874 Reducer 1
D3 6V-9746 O-Ring Seal 1
D4 124-1901 Permanent Coupling 1
D5 122-6870 Bulk Hydraulic Hose 3 ft
D6 124-2147 Permanent Coupling 1
D7 6V-8942 O-Ring Reducer 1
D8 6V-8556 Nut 1
D9 6V-8398 O-Ring Seal 1
F 311-1362 Vacuum Cap 1 Reference: Refer to Tool Operating Manual, NEHS1087 for operating instructions for the 348-5430 Multi-Tool Gp.Note: Use Software License Card, NETG5049 with part number 348-5430 Multi-Tool Gp.Machine Preparation
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Note: Set the pilot relief valve to the specification. Refer to Testing and Adjusting, "Relief Valve (Pilot) - Test and Adjust".
Position the machine on level ground.
Stop the engine.
Release the pressure in the hydraulic system. Refer to Testing and Adjusting, "System Pressure - Release".
Attach 311-1362 Vacuum Cap onto the hydraulic tank. Attach an air supply hose onto the assembly. Apply 276 to 414 kPa (40 to 60 psi). This procedure will pull a vacuum on the hydraulic system.
Illustration 4 g02155948
Flow meter tool layout
Tooling (D)
( 1) Pilot pump
(2) Connector
(3) Hose
(4) Pilot filter
Install the following tools in accordance with the flow meter tool layout. Refer to Illustration 4.
Disconnect hose (3) from connector (2).
Connect flow meter assembly (D) between connector (2) and hose (3). Note: Correct orientation of the flow meter is necessary. The oil flows from pilot pump (1) to pilot filter (4).
Remove 311-1362 Vacuum Cap.
Install tooling (C) on the engine to monitor engine speed. Test Procedure
Start the engine.
Increase the hydraulic oil temperature to 55° 5°C (131° 9°F).
Place the machine controls at the following settings: engine speed dial "10" and AEC switch OFF. Refer to Testing and Adjusting, "Engine Performance - Test (Engine Speed)" for engine rpm settings.
Check the flow of oil through the flow meter. Refer to Table 1.

Caterpillar parts catalog:

Caterpillar parts catalog
E240B, EL240B TRACK-TYPE EXCAVATORS 5WG00001-UP (MACHINE) POWERED BY 3116 ENGINE


Parts net Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.