AVSPARE.COM
parts catalog

NIPPLE PIPE 0002443 - Caterpillar



0002443 NIPPLE PIPE Caterpillar parts NIPPLE
Rating:
71
Alternative (cross code) number:
CA0002443
000-2443
0002443
Caterpillar 0002443 NIPPLE PIPE

Buy NIPPLE PIPE 0002443 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Illustration 1 g01004785
Schematic of the Joystick Control CircuitThis diagnostic code is associated with the Joystick Forward/Reverse Position Sensor. This diagnostic code is recorded when the ECM reads the sensor signal as being below normal. There is a short to ground. Note: The sensor is probably out of specification, if the diagnostic code is present under certain operating conditions. As an example, the joystick is "full forward" or the joystick is "full reverse". Recalibrate the sensor. See Testing and Adjusting, "Position Sensor (Forward/Neutral/Reverse) of Joystick Control - Calibrate" for more information.The possible causes of this diagnostic code are listed:
The sensor supply (wire 709-OR) from the electrical system to the sensor is open.
The signal circuit is shorted to ground.
The sensor has failed.
The ECM has failed. This is unlikely. Note: Ensure that CID 1699 FMI 04 is on hold and that the diagnostic indicator is illuminated. Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear the diagnostic codes when the original diagnostic code has been corrected.System Response:When this diagnostic code occurs, the action lamp and the action alarm is ON. The diagnostic code will cause the joystick to stop functioning. The machine will decelerate to a stop.Test Step 1. CHECK THE SENSOR.
Turn the disconnect switch and the key start switch to the ON position.
Ensure that the diagnostic code is active.
Observe the status of the diagnostic code. Then, disconnect the sensor from the machine harness.Expected Result:The diagnostic code will remain active if the sensor is not the cause of the diagnostic code. The sensor is the cause of the diagnostic code if the diagnostic code is NO longer active.Results:
OK - The diagnostic code remains active. The sensor has not failed. The machine harness may have failed or the ECM may have failed. Proceed to test step 2.
NOT OK - The diagnostic code is NO longer active. The machine harness and the ECM are operating properly.Repair: The sensor has failed. Replace the joystick. Calibrate the sensor. See Testing and Adjusting, "Position Sensor (Forward/Neutral/Reverse) of Joystick Control - Calibrate" for more information. Verify that the new joystick corrects the problem.STOPTest Step 2. CHECK THE SIGNAL CIRCUIT FOR A SHORT TO GROUND.
The sensor remains disconnected from the machine harness.
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the J1 and J2 machine harness connector from the ECM.
At the J1 machine harness connector, measure the resistance from contact J2-26 (wire F853-BR) to all contacts that are used in the machine harness connectors for the ECM.Expected Result:The resistance is greater than 5000 ohms for each measurement.Results:
OK - The resistance is greater than 5000 ohms for each measurement. The ECM may have failed.Repair: It is unlikely that the ECM has failed. Exit this procedure and perform this procedure again. If the cause of the diagnostic code is not found, replace the ECM. See Testing and Adjusting, "Electronic Control Module (ECM) - Replace".STOP
NOT OK - The resistance is less than 5000 ohms for one or more of


Parts nipple Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.