0R1742 NOZZLE AS Caterpillar parts
Rating:
Alternative (cross code) number:
CA0R1742
0R-1742
0R1742
CA0R1742
0R-1742
0R1742
Weight: 0.80 pounds 0 kg.
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
4Pcs New Fuel Injection Nozzle Suitable for CAT 3204 Engine Excavator 215B E180 EL180 Track Loader 931 931B 931C 931C II 935B 935C 935C II 943 953 4W-7015 OR3419 0R1742 1W3996
TuneCrumph Part Name:Fuel Injector || Part Number:4W-7015 OR3419 0R1742 1W3996 || Application:Suitable for CAT 3204 Engine Excavator 215B E180 EL180 Track Loader 931 931B 931C 931C II 935B 935C 935C II 943 953 4W-7015 OR3419 0R1742 1W3996 || Attention: Dear buyers, precise matching of auto parts is the prerequisite for safe installation! To avoid the problems such as returns, exchanges or installation hazards caused by incorrect model selection, please carefully read and verify the model before placing your order. Thank you for your support! || NOTE:We are fully aware that your satisfaction is the driving force for the growth of our brand. Thank you for giving us the opportunity to serve you. If there is anything we haven't covered, please give us your feedback directly. Your suggestions are extremely precious to us!
TuneCrumph Part Name:Fuel Injector || Part Number:4W-7015 OR3419 0R1742 1W3996 || Application:Suitable for CAT 3204 Engine Excavator 215B E180 EL180 Track Loader 931 931B 931C 931C II 935B 935C 935C II 943 953 4W-7015 OR3419 0R1742 1W3996 || Attention: Dear buyers, precise matching of auto parts is the prerequisite for safe installation! To avoid the problems such as returns, exchanges or installation hazards caused by incorrect model selection, please carefully read and verify the model before placing your order. Thank you for your support! || NOTE:We are fully aware that your satisfaction is the driving force for the growth of our brand. Thank you for giving us the opportunity to serve you. If there is anything we haven't covered, please give us your feedback directly. Your suggestions are extremely precious to us!
4pcs Fuel Injector 0R-1742 4W-7015 Fits for CAT 3204 Excavator E180 EL180 215B 931B 931C
XYohykai ◆Part Name◆:Fuel Injector || ◆Part Number◆:0R-3419 0R3419 0R-1742 0R1742 4W7015 || ◆Application◆:Fits for CAT 3204 Excavator E180 EL180 215B 931B 931C || ◆Notice◆-Application information provided is for reference only. Please confirm the part number and compare old parts before purchase. If you have any question,pls feel free to ask us. || ◆Worth Choice◆-This product has stable performance high reliability easy installation and fast response.
XYohykai ◆Part Name◆:Fuel Injector || ◆Part Number◆:0R-3419 0R3419 0R-1742 0R1742 4W7015 || ◆Application◆:Fits for CAT 3204 Excavator E180 EL180 215B 931B 931C || ◆Notice◆-Application information provided is for reference only. Please confirm the part number and compare old parts before purchase. If you have any question,pls feel free to ask us. || ◆Worth Choice◆-This product has stable performance high reliability easy installation and fast response.
shsiyayh 1PCS Fuel Injector for Caterpillar CAT 3204 Excavator E180 EL180 215B 931B 931C 0R-1742 0R1742
shsiyayh Part Name:Fuel Injector || Part Number:0R-1742 0R1742 || APPlication: Compatible with Caterpillar CAT 3204 Excavator E180 EL180 215B 931B 931C || 1.Please tell us of your engine model or a view of nameplate when order this item to lower the error rate.Thanks. || 2.There are no instructions included in this kit.it is recommended to install professionally.
shsiyayh Part Name:Fuel Injector || Part Number:0R-1742 0R1742 || APPlication: Compatible with Caterpillar CAT 3204 Excavator E180 EL180 215B 931B 931C || 1.Please tell us of your engine model or a view of nameplate when order this item to lower the error rate.Thanks. || 2.There are no instructions included in this kit.it is recommended to install professionally.
For full view, you need register
Information:
This procedure covers the following codes:
Table 1
Diagnostic Trouble Codes for the Exhaust Gas Pressure Sensor
J1939 Code Description Notes
1209-3 Engine Exhaust Gas Pressure : Voltage Above Normal The ECM detects the following conditions:
The signal voltage from the exhaust gas pressure sensor is greater than 4.74 VDC for at least 1.8 seconds.
The battery voltage is at least 10 VDC.
The ECM will use the default value for exhaust gas pressure while this code is active. The default value is 50 kPa (7.25 psi).
The warning lamp will flash. The engine will be derated.
1209-4 Engine Exhaust Gas Pressure : Voltage Below Normal The ECM detects the following conditions:
The signal voltage from the exhaust gas pressure sensor is less than 0.4 VDC for at least 1.8 seconds.
The battery voltage is at least 10 VDC.
The ECM will use the default value for exhaust gas pressure while this code is active. The default value is 50 kPa (7.25 psi).
The warning lamp will flash. The engine will be derated. The following conditions must exist before any of the above codes will become active:
There are no active 3509 codes.
There are no active 168 codes.The following background information is related to this procedure:The 5 V sensor supply provides power to all 5 V sensors. The ECM supplies 5.0 0.1 V to each of the pressure sensor connectors. The sensor supply is output short circuit protected. A short circuit to the battery will not damage the circuit inside the ECM.
Illustration 1 g03732081
Schematic diagram for the exhaust gas pressure sensor
Illustration 2 g03732082
View of the pin locations on the 62-pin connector for the exhaust gas pressure sensor
(21) Exhaust gas pressure sensor 5 V supply
(22) Exhaust gas pressure sensor ground
(23) Exhaust gas pressure sensor signal
Illustration 3 g03732083
View of the pin locations on the P1 connector for the exhaust gas pressure sensor
(18) Exhaust gas pressure sensor 5 V supply
(37) Exhaust gas pressure sensor ground
(57) Exhaust gas pressure sensor signal
Table 2
Troubleshooting Test Steps Values Results
1. Inspect Electrical Connectors and Wiring
A. Thoroughly inspect the terminal connections on the P2/J2 ECM connector. Refer to Troubleshooting, "Electrical Connectors - Inspect".
B. Thoroughly inspect the connector for the exhaust gas pressure sensor. Refer to Troubleshooting, "Electrical Connectors - Inspect".
C. Perform a 30 N (6.7 lb) pull test on each of the wires in the ECM connector and the sensor connectors that are associated with the exhaust gas pressure sensor.
D. Check the harness for abrasions and for pinch points from the exhaust gas pressure sensor back to the ECM.
Damaged wire or connector
Result: A damaged wire or damaged connector was found.
Repair: Repair the damaged wire or the damaged connector.
Use the electronic service tool to clear all logged diagnostic codes. Verify that the repair eliminates the fault.
Result: All connectors, pins, and sockets are correctly connected and/or inserted and the harness is free of corrosion, of abrasion or of pinch points.
Proceed to Test Step 2.
2. Check For Active Diagnostic Codes
A. Turn the keyswitch to the ON position. Wait at least 10 seconds for activation of the diagnostic codes.
B. Verify if any of the diagnostic codes that
Table 1
Diagnostic Trouble Codes for the Exhaust Gas Pressure Sensor
J1939 Code Description Notes
1209-3 Engine Exhaust Gas Pressure : Voltage Above Normal The ECM detects the following conditions:
The signal voltage from the exhaust gas pressure sensor is greater than 4.74 VDC for at least 1.8 seconds.
The battery voltage is at least 10 VDC.
The ECM will use the default value for exhaust gas pressure while this code is active. The default value is 50 kPa (7.25 psi).
The warning lamp will flash. The engine will be derated.
1209-4 Engine Exhaust Gas Pressure : Voltage Below Normal The ECM detects the following conditions:
The signal voltage from the exhaust gas pressure sensor is less than 0.4 VDC for at least 1.8 seconds.
The battery voltage is at least 10 VDC.
The ECM will use the default value for exhaust gas pressure while this code is active. The default value is 50 kPa (7.25 psi).
The warning lamp will flash. The engine will be derated. The following conditions must exist before any of the above codes will become active:
There are no active 3509 codes.
There are no active 168 codes.The following background information is related to this procedure:The 5 V sensor supply provides power to all 5 V sensors. The ECM supplies 5.0 0.1 V to each of the pressure sensor connectors. The sensor supply is output short circuit protected. A short circuit to the battery will not damage the circuit inside the ECM.
Illustration 1 g03732081
Schematic diagram for the exhaust gas pressure sensor
Illustration 2 g03732082
View of the pin locations on the 62-pin connector for the exhaust gas pressure sensor
(21) Exhaust gas pressure sensor 5 V supply
(22) Exhaust gas pressure sensor ground
(23) Exhaust gas pressure sensor signal
Illustration 3 g03732083
View of the pin locations on the P1 connector for the exhaust gas pressure sensor
(18) Exhaust gas pressure sensor 5 V supply
(37) Exhaust gas pressure sensor ground
(57) Exhaust gas pressure sensor signal
Table 2
Troubleshooting Test Steps Values Results
1. Inspect Electrical Connectors and Wiring
A. Thoroughly inspect the terminal connections on the P2/J2 ECM connector. Refer to Troubleshooting, "Electrical Connectors - Inspect".
B. Thoroughly inspect the connector for the exhaust gas pressure sensor. Refer to Troubleshooting, "Electrical Connectors - Inspect".
C. Perform a 30 N (6.7 lb) pull test on each of the wires in the ECM connector and the sensor connectors that are associated with the exhaust gas pressure sensor.
D. Check the harness for abrasions and for pinch points from the exhaust gas pressure sensor back to the ECM.
Damaged wire or connector
Result: A damaged wire or damaged connector was found.
Repair: Repair the damaged wire or the damaged connector.
Use the electronic service tool to clear all logged diagnostic codes. Verify that the repair eliminates the fault.
Result: All connectors, pins, and sockets are correctly connected and/or inserted and the harness is free of corrosion, of abrasion or of pinch points.
Proceed to Test Step 2.
2. Check For Active Diagnostic Codes
A. Turn the keyswitch to the ON position. Wait at least 10 seconds for activation of the diagnostic codes.
B. Verify if any of the diagnostic codes that
Parts nozzle Caterpillar catalog:
Caterpillar
Caterpillar
0R1739
NOZZLE AS
Caterpillar
Caterpillar
0997513
NOZZLE A
Caterpillar
Caterpillar
0997511
NOZZLE
Caterpillar
Caterpillar
0994919
NOZZLE TIP ASS
Caterpillar
Caterpillar
0R1748
NOZZLE A-
Caterpillar
Caterpillar
Caterpillar
Caterpillar
Caterpillar
Caterpillar
Caterpillar