1R5839 NUT Caterpillar parts
312, 312B, 312C, 312C L, 313B, 314C, E120B
Rating:
Alternative (cross code) number:
CA1R5839
1R-5839
1R5839
CA1R5839
1R-5839
1R5839
Weight: 3 pounds 1 kg.
EXCAVATOR,
Number on catalog scheme:
4
For full view, you need register
Information:
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
B 1P-0510 Driver Group 1
C FT-2398 Oil Pump Shaft Tool 1
0S-1627 Bolts 2
2J-3506 Full Nuts 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01209057Note: On the lower bearing, align the hole in the bearing with the hole in the oil pump's body.
Apply a coat of clean engine oil to the outside of each bearing. Use Tooling (B) and a suitable press to install bearings (11) into pump body (9). Install the bearings 12.30 0.25 mm (0.484 0.010 inch) below the surface of pump body (9). The inside diameter of the bearings must be 60.039 0.040 mm (2.3637 0.0016 inch) after installation.
Illustration 2 g01209062
Apply a coat of clean engine oil to the outside of each bearing. Use Tooling (B) and a suitable press to install bearings (7) into cover (6). Align the hole in the bearing with the hole in the cover. Install the bearings 7.50 0.25 mm (0.230 0.010 inch) below the surface of cover (6). The inside diameter of the bearings must be 60.039 0.040 mm (2.3637 0.0016 inch) after installation.
Illustration 3 g01209063
Ensure that dowels (14) are installed to a height of 12.0 1.0 mm (0.47 0.04 inch).
Place O-ring seal (12) and O-ring seals (13) in position on cover (6). Apply clean engine oil to the O-ring seals.
Apply a coat of clean engine oil to the bearings and the gear pockets in pump body (9).
Place drive shaft (8) and idler shaft (10) in pump body (9). Ensure that the gears are 0.14 mm to 0.16 mm (0.006 inch to 0.010 inch) below the surface of the pump body.
Apply clean engine oil to the bearings in cover (6). Apply clean engine oil to the top surface of the gears in pump body (9).
Place cover (6) in position on pump body (9).
Illustration 4 g01209072
Ensure that cover (6) is against the pump body. Ensure that all the O-ring seals are in place. Install the bolts that hold cover (6) to the pump body.
Ensure that plug (15) is installed in the idler shaft.
Ensure that plug (16) is installed in the cover.
Illustration 5 g01209075
Illustration 6 g00628384Note: Ensure that dowel (17) is installed at the location that is shown in Illustration 5 for a SAE standard rotation engine.
Install dowel (17) to a height of 8.0 1.0 mm (0.32 0.04 inch).
Ensure that plugs (18) are installed.
Use Tooling (C) to install gear (5) and the washer. Install bolt (4). Tighten bolt (4) to a torque of 370 50 N m (273 37 lb ft).
Strike the head of the bolt with a hammer. Tighten the bolt (4) again to a torque of 370 50 N m (273 37 lb ft).
Install drive gear (3).
Illustration 7 g01209076
Ensure that plug (19) is installed in the drive shaft.
Ensure that hollow dowel (20) is installed to a height of 4.0 0.5 mm (0.16 0.02 inch).
Place the O-ring seal on
Table 1
Required Tools
Tool Part Number Part Description Qty
B 1P-0510 Driver Group 1
C FT-2398 Oil Pump Shaft Tool 1
0S-1627 Bolts 2
2J-3506 Full Nuts 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01209057Note: On the lower bearing, align the hole in the bearing with the hole in the oil pump's body.
Apply a coat of clean engine oil to the outside of each bearing. Use Tooling (B) and a suitable press to install bearings (11) into pump body (9). Install the bearings 12.30 0.25 mm (0.484 0.010 inch) below the surface of pump body (9). The inside diameter of the bearings must be 60.039 0.040 mm (2.3637 0.0016 inch) after installation.
Illustration 2 g01209062
Apply a coat of clean engine oil to the outside of each bearing. Use Tooling (B) and a suitable press to install bearings (7) into cover (6). Align the hole in the bearing with the hole in the cover. Install the bearings 7.50 0.25 mm (0.230 0.010 inch) below the surface of cover (6). The inside diameter of the bearings must be 60.039 0.040 mm (2.3637 0.0016 inch) after installation.
Illustration 3 g01209063
Ensure that dowels (14) are installed to a height of 12.0 1.0 mm (0.47 0.04 inch).
Place O-ring seal (12) and O-ring seals (13) in position on cover (6). Apply clean engine oil to the O-ring seals.
Apply a coat of clean engine oil to the bearings and the gear pockets in pump body (9).
Place drive shaft (8) and idler shaft (10) in pump body (9). Ensure that the gears are 0.14 mm to 0.16 mm (0.006 inch to 0.010 inch) below the surface of the pump body.
Apply clean engine oil to the bearings in cover (6). Apply clean engine oil to the top surface of the gears in pump body (9).
Place cover (6) in position on pump body (9).
Illustration 4 g01209072
Ensure that cover (6) is against the pump body. Ensure that all the O-ring seals are in place. Install the bolts that hold cover (6) to the pump body.
Ensure that plug (15) is installed in the idler shaft.
Ensure that plug (16) is installed in the cover.
Illustration 5 g01209075
Illustration 6 g00628384Note: Ensure that dowel (17) is installed at the location that is shown in Illustration 5 for a SAE standard rotation engine.
Install dowel (17) to a height of 8.0 1.0 mm (0.32 0.04 inch).
Ensure that plugs (18) are installed.
Use Tooling (C) to install gear (5) and the washer. Install bolt (4). Tighten bolt (4) to a torque of 370 50 N m (273 37 lb ft).
Strike the head of the bolt with a hammer. Tighten the bolt (4) again to a torque of 370 50 N m (273 37 lb ft).
Install drive gear (3).
Illustration 7 g01209076
Ensure that plug (19) is installed in the drive shaft.
Ensure that hollow dowel (20) is installed to a height of 4.0 0.5 mm (0.16 0.02 inch).
Place the O-ring seal on
Caterpillar parts catalog:
Parts nut Caterpillar catalog:
115, 311, 311B, 311C, 311D LRR, 311F LRR, 312, 312B, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 313D2, 314D CR, 314D LCR, 314E CR, 314E LCR, 315, 315B, 315B L, 315C, 315D L, 317, 320 ...
1090, 1190T, 2290, 311, 311B, 311C, 312, 312B, 313D2 LGP, 315, 315B, 315B FM L, 315B L, 315C, 315D L, 316E L, 317, 317B LN, 318B, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320, 320 L...
311, 311B, 311C, 311D LRR, 311F LRR, 312, 312B, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313B, 313D, 313D2, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, D3C III, D3G,...
215, 215B, 225, 235, 312, 315, 315B L, 317, 317B LN, 320, 325, 920, 924F, 924G, 924GZ, 924H, 924HZ, 924K, 926, 928G, 928HZ, 930, 930G, 930K, 930R, 936F, 938F, 938G, 938G II, 938H, 938K, 939, 939C, 941...
304, 305, 307, 307B, 307C, 308C, 311B, 311C, 312C, 312C L, 312D, 313B, 314C, 315C, 321C, 321D LCR, 325C, 328D LCR, 345B II, 345B L, 345C, 345C L, 345D, 345D L, 349D, 349D L, 349E L, 349E L VG, 349F L,...
120M, 120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 301.6C, 311C, 314C, 318B, 320 L, 320B, 325 L, 325 LN, 325B, 325C, 330C, 330C L...
307, 311, 311B, 311C, 311D LRR, 312B, 312C, 312C L, 312D, 312D L, 313D, 314C, 314D CR, 314D LCR, 315D L, 318C, 318D L, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D FM, 3...
311C, 312, 312C, 312C L, 314C, E120B, E70, E70B
311C, 311D LRR, 311F LRR, 312C L, 312D, 312D L, 312D2, 312D2 L, 312E, 312E L, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 316E L, 318C, 318D2 L, 318E L, 319D L, 320C, 320C FM, 320C L, 320D, 320D FM, 3...
311C, 311D LRR, 312C, 312C L, 312D, 312D L, 313D, 314C, 314D CR, 314D LCR, 315D L, 318C, 318D L, 319C, 319D, 319D L, 319D LN, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN...
312, 312C L, E110, E110B, E120, E120B
120M, 120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 160M, 160M 2, 160M 3, 160M 3 AWD, 320C, 320D L, 321C, E110, E120, E120B, E140, E180, E240, E240C, E70, E70B, EL240, EL240B
303, 307, 307B, 307C, 308C, 311C, 312, 312B L, 313B, 314C, 315, 315B L, 317, 317B LN, 318B, 320 L, 321C, 325C
1W9589
NUT
311, 312, 320, 320 L, 320N, 322 LN, 325, 330, 330 L, 950K, 962K, 966K, 966M, 966M XE, 972K, 972M, 972M XE, 980K, 980K HLG, 980M, 982M, CS-531C, CS-533C, CS-563C, CS-573C, CS-583C
311, 312, 320, 320 L, 320N, 322 LN, 325, 330, 330 L, 950K, 962K, 966K, 966M, 966M XE, 972K, 972M, 972M XE, 980K, 980K HLG, 980M, 982M, CS-531C, CS-533C, CS-563C, CS-573C, CS-583C
1236153
NUT-WING
312, 315, 317, 320B, 322B LN, 325B L, 330B L
312, 315, 317, 320B, 322B LN, 325B L, 330B L
120H, 120H ES, 120H NA, 135H, 135H NA, 225, 227, 235C, 235D, 245, 350, 350 L, 375, 5080, 627E, 627F, 637E, 657E, 834B, 920, 943, 950B, 953, 960F, 962G, 963, 963B, 973, 994, 994D, 994F, 994H, D5B, D5E,...
235, 235B, 235C, 235D, 973, 973C, 973D, D7G, D7G2
9G2978
NUT
225, 8D
225, 8D
6C9192
NUT
311B, 312, 312B L, 315, 315B L, 317, 317B LN, 318B, 320 L, 320B, 322B LN, 325 L, 325B L, 330B L, 345B II, 345B L, 350, 350 L, 375, 5080
311B, 312, 312B L, 315, 315B L, 317, 317B LN, 318B, 320 L, 320B, 322B LN, 325 L, 325B L, 330B L, 345B II, 345B L, 350, 350 L, 375, 5080
6C9238
NUT
307B, 311B, 312, 312B L, 315, 315B L, 317, 317B LN, 318B, 320 L, 320B, 322B LN, 325 L, 325B L, 330B L, 345B II, 345B L, 350, 365B, 365B II, 375, 375 L, 385B, 5080, 5090B
307B, 311B, 312, 312B L, 315, 315B L, 317, 317B LN, 318B, 320 L, 320B, 322B LN, 325 L, 325B L, 330B L, 345B II, 345B L, 350, 365B, 365B II, 375, 375 L, 385B, 5080, 5090B
0937676
NUT
307, 307B, 307C, 311, 311B, 311C, 311D LRR, 311F LRR, 312, 312C L, 312D, 312D L, 312E, 313B, 314C, 314D LCR, 314E CR, E110, E110B, E120, E120B, E140, E180, E240, E70, E70B, M312, M315
307, 307B, 307C, 311, 311B, 311C, 311D LRR, 311F LRR, 312, 312C L, 312D, 312D L, 312E, 313B, 314C, 314D LCR, 314E CR, E110, E110B, E120, E120B, E140, E180, E240, E70, E70B, M312, M315
7I8100
NUT
311, 311B, 311C, 312, 312B, 312B L, 312C, 312C L, 312D, 313B, 314C, 315, 315B, 315B L, 315C, 315D L, 317, 317B LN, 318B, 319D, 319D LN
311, 311B, 311C, 312, 312B, 312B L, 312C, 312C L, 312D, 313B, 314C, 315, 315B, 315B L, 315C, 315D L, 317, 317B LN, 318B, 319D, 319D LN
1390, 2590, 301.5, 302.5, 303, 303.5, 304, 304.5, 305.5, 306, 311, 311B, 312, 312B, 312B L, 315, 315B, 315B L, 317, 317B LN, 318B, 320C, 320D L, 330, 330 FM L, 330 L, 541, 541 2, 551, 552, 552 2, 950G...
0964874
NUT
307, 311, 312, 312C L, 320 L, 325, 325 L, 325 LN, 330, 350, 375, 375 L, E110, E110B, E120, E120B, E140, E180, E200B, E240, E240C, E300B, E650, E70, E70B, EL240B
307, 311, 312, 312C L, 320 L, 325, 325 L, 325 LN, 330, 350, 375, 375 L, E110, E110B, E120, E120B, E140, E180, E200B, E240, E240C, E300B, E650, E70, E70B, EL240B