AVSPARE.COM
parts catalog

NUT-CONT.ROD 2H9286 - Caterpillar



2H9286 NUT-CONT.ROD Caterpillar parts NUT
Rating:
46
Alternative (cross code) number:
CA2H9286
2H-9286
2H9286
Caterpillar 2H9286 NUT-CONT.ROD
Weight: 0.010 pounds 0 kg.

Buy NUT-CONT.ROD 2H9286 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Illustration 1 g01258905
Schematic for the LSI Hydraulic Lockout Override SwitchThis diagnostic code is associated with the Longitudinal Stability Indicator (LSI) Hydraulic Lockout Override Switch. The FMI 02 means that the ECM has determined that the signal is erratic, intermittent, or incorrect. The ECM could be receiving invalid combinations from the circuit.System Response:The system will default to no active LSI override.Test Step 1. CHECK THE CONTINUITY OF THE SWITCH IN THE NORMAL POSITION
Turn the key start switch and the disconnect switch to the "OFF" position.
Remove the switch from the dash.
Unplug the switch from the wire harness.
With the switch in the Normal position, check resistances from terminal "2" to each of the following: terminals 1, 3, 4 and 6. Next check resistances from terminal "5" to each of the following: terminals 1, 3, 4 and 6.Expected Result:All of the resistance measurements are greater than 5000 Ohms.Results:
OK - All measured resistances are greater than 5000 Ohms. Proceed to Test Step 2.
NOT OK - One or more resistance is less than 5000 Ohms.Repair: The switch has failed. Replace the switch.STOPTest Step 2. CHECK THE CONTINUITY OF THE SWITCH IN THE OVERRIDE ON POSITION
Press and hold the switch in the Override ON position.
With the switch held in the "ON" position, check resistances from terminal "2" to each of the following: terminals 1, 3, 4 and 6. Next check resistances from terminal "5" to each of the following: terminals 1, 3, 4 and 6.Expected Result:The resistance from terminal 2 to terminal 3 should be less than 5 Ohms. The resistances from terminal 2 to terminals 1, 4, and 6 is greater than 5000 Ohms.The resistance from terminal 5 to terminal 6 should be less than 5 Ohms. The resistances from terminal 5 to terminals 1, 3, and 4 is greater than 5000 Ohms.Results:
OK - All measured resistances are correct. Proceed to Test Step 3.
NOT OK - One or more resistances are NOT correct.Repair: The switch has failed. Replace the switch.STOPTest Step 3. CHECK THE CONTINUITY OF THE SWITCH IN THE OVERRIDE OFF POSITION
Press and hold the switch in the Override OFF position.
With the switch held in the "OFF" position, check resistances from terminal "2" to each of the following: terminals 1, 3, 4 and 6. Next check resistances from terminal "5" to each of the following: terminals 1, 3, 4 and 6.Expected Result:The resistance from terminal 2 to terminal 1 should be less than 5 Ohms. The resistances from terminal 2 to terminals 3, 4, and 6 is greater than 5000 Ohms.The resistance from terminal 5 to terminal 4 should be less than 5 Ohms. The resistances from terminal 5 to terminals 1, 3, and 6 is greater than 5000 Ohms.Results:
OK - All measured resistances are correct. Proceed to Test Step 4.
NOT OK - One or more resistances are NOT correct.Repair: The switch has failed. Replace the switch.STOPTest Step 4. CHECK THE HARNESS
The key start switch and the disconnect switch remain in the "OFF" position.
The switch remains disconnected from the harness.
Disconnect the "J1" and "J2"


Parts nut Caterpillar catalog:

2H8230 NUT
Caterpillar
2H8213 NUT
Caterpillar
2H8204 NUT
Caterpillar
2H6238 NUT
Caterpillar
2H6132 NUT
Caterpillar
2I3027 NUT
Caterpillar
2I3023 NUT
Caterpillar
2I2984 NUT
Caterpillar
2I2759 NUT
Caterpillar
2I2706 NUT
Caterpillar
2I2705 NUT
Caterpillar
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.