5I7626 NUT Caterpillar parts
318C, 319C, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D LRR, 321C, 323D L, 323D LN, M322D, M322D MH
Rating:
Alternative (cross code) number:
CA5I7626
5I-7626
5I7626
CA5I7626
5I-7626
5I7626
Weight: 0.05 pounds 0 kg.
EXCAVATOR, WHEELED EXCAVATOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$12.51
29 Apr 2022
US: Florida-Parts-Z
5I7626 - NUT for Caterpillar (CAT)
FIRST PRICE PARTS
FIRST PRICE PARTS
$4.61
02 Jul 2022
US: ProperBuy
CTP 5I7626 Hex Head Nut for Heavy Equipment
CTP Hex Head Type of Nut || Sold in each || Easy in-and-out fit
CTP Hex Head Type of Nut || Sold in each || Easy in-and-out fit
$7.69
08 Jan 2019
CATERPILLAR AFTERMARKET: CATERPILLAR AFT
Caterpillar NUT 5I7626 New
Number on catalog scheme:
4
For full view, you need register
Compatible equipment models: 5I7626:
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Gp 1
B 8T-2998 Lubricant -
C - Loctite 5900 -
D - Loctite 243 -
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Do not turn the crankshaft or the camshaft while the camshaft gear is removed. If the front gear group is not correctly timed during installation, interference can occur between the pistons and the valves, resulting in damage to the engine.
Thoroughly clean the gasket material from the cylinder block and both sides of the plate.
Illustration 1 g01101567
If studs (24) are loose or the threads are damaged, install new studs (24) in the front plate. Apply Tooling (D) to the serrations of studs (24). Install studs (24) in the front plate.
Install integral seal (25) on the dowel pins on the cylinder block. Note: Apply Tooling (C) to the bottom of integral seal (25) in order to fill the space at the cylinder block, the front housing, and the engine oil pan.
Install plate (22) on the dowel pins on the cylinder block. Install new locking bolts (23) (Marked "X") in order to fasten the front plate to the cylinder block. Tighten locking bolts (23) to a torque of 55 N m (41 lb ft). Note: Clean the old sealant from the bolts and apply Tooling (D) to the bolts.
Tighten locking bolts (23) again to a torque of 55 N m (41 lb ft).
Illustration 2 g01101565
Install stub shaft (18). Apply Tooling (D) to the studs and the bolt for stub shaft (18). Tighten nuts (19) and the bolt to a torque of 55 10 N m (41 7 lb ft).
Install stub shaft assembly (16). Apply Tooling (D) to the studs and the bolt for stub shaft assembly (16). Do not tighten nuts (17) and the bolt for stub shaft assembly (16) at this time. Nuts (17) and the bolt for stub shaft assembly (16) will need to be tightened when the backlash is adjusted.
Adjust the backlash between the camshaft gear and the adjustable idler gear assembly. The backlash should be 0.3556 0.254 mm (0.014 0.010 inch). Refer to Testing and Adjusting, "Gear Group (Front) - Time" for the backlash adjustment procedure. Tighten nuts (17) and the bolt to a torque of 55 10 N m (41 7 lb ft).
Install stub shaft (20). Apply Tooling (D) to bolts (21). Install bolts (21) and tighten in a numeric sequence 1, 3, 4, 5, 2, 1, 2, 3, 4, 5, 1 to a torque of 55 10 N m (41 7 lb ft).
Illustration 3 g01101161
Use Tooling (A) to install the sleeve bearing in cluster gear assembly (13).
Put cluster gear assembly (13) on the stub shaft. Ensure that Timing Marks (V) are aligned on the cluster gear assembly and the crankshaft gear.
Position plate (15) with the oil groove toward the face of the gear. Apply Tooling (D) to bolts (14). Install bolts (14). Tighten bolts (14) to a
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Gp 1
B 8T-2998 Lubricant -
C - Loctite 5900 -
D - Loctite 243 -
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Do not turn the crankshaft or the camshaft while the camshaft gear is removed. If the front gear group is not correctly timed during installation, interference can occur between the pistons and the valves, resulting in damage to the engine.
Thoroughly clean the gasket material from the cylinder block and both sides of the plate.
Illustration 1 g01101567
If studs (24) are loose or the threads are damaged, install new studs (24) in the front plate. Apply Tooling (D) to the serrations of studs (24). Install studs (24) in the front plate.
Install integral seal (25) on the dowel pins on the cylinder block. Note: Apply Tooling (C) to the bottom of integral seal (25) in order to fill the space at the cylinder block, the front housing, and the engine oil pan.
Install plate (22) on the dowel pins on the cylinder block. Install new locking bolts (23) (Marked "X") in order to fasten the front plate to the cylinder block. Tighten locking bolts (23) to a torque of 55 N m (41 lb ft). Note: Clean the old sealant from the bolts and apply Tooling (D) to the bolts.
Tighten locking bolts (23) again to a torque of 55 N m (41 lb ft).
Illustration 2 g01101565
Install stub shaft (18). Apply Tooling (D) to the studs and the bolt for stub shaft (18). Tighten nuts (19) and the bolt to a torque of 55 10 N m (41 7 lb ft).
Install stub shaft assembly (16). Apply Tooling (D) to the studs and the bolt for stub shaft assembly (16). Do not tighten nuts (17) and the bolt for stub shaft assembly (16) at this time. Nuts (17) and the bolt for stub shaft assembly (16) will need to be tightened when the backlash is adjusted.
Adjust the backlash between the camshaft gear and the adjustable idler gear assembly. The backlash should be 0.3556 0.254 mm (0.014 0.010 inch). Refer to Testing and Adjusting, "Gear Group (Front) - Time" for the backlash adjustment procedure. Tighten nuts (17) and the bolt to a torque of 55 10 N m (41 7 lb ft).
Install stub shaft (20). Apply Tooling (D) to bolts (21). Install bolts (21) and tighten in a numeric sequence 1, 3, 4, 5, 2, 1, 2, 3, 4, 5, 1 to a torque of 55 10 N m (41 7 lb ft).
Illustration 3 g01101161
Use Tooling (A) to install the sleeve bearing in cluster gear assembly (13).
Put cluster gear assembly (13) on the stub shaft. Ensure that Timing Marks (V) are aligned on the cluster gear assembly and the crankshaft gear.
Position plate (15) with the oil groove toward the face of the gear. Apply Tooling (D) to bolts (14). Install bolts (14). Tighten bolts (14) to a
Caterpillar parts catalog:
Parts nut Caterpillar catalog:
115, 311, 311B, 311C, 311D LRR, 311F LRR, 312, 312B, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 313D2, 314D CR, 314D LCR, 314E CR, 314E LCR, 315, 315B, 315B L, 315C, 315D L, 317, 320 ...
1090, 1190T, 2290, 311, 311B, 311C, 312, 312B, 313D2 LGP, 315, 315B, 315B FM L, 315B L, 315C, 315D L, 316E L, 317, 317B LN, 318B, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320, 320 L...
304, 305, 307, 307B, 307C, 308C, 311B, 311C, 312C, 312C L, 312D, 313B, 314C, 315C, 321C, 321D LCR, 325C, 328D LCR, 345B II, 345B L, 345C, 345C L, 345D, 345D L, 349D, 349D L, 349E L, 349E L VG, 349F L,...
313D2 LGP, 315B FM L, 315C, 315D L, 316E L, 317B LN, 318B, 318C, 318D L, 318D2 L, 319C, 320 L, 320B, 320B L, 320C, 320C L, 320N, 321C, OEMS
120M, 120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 301.6C, 311C, 314C, 318B, 320 L, 320B, 325 L, 325 LN, 325B, 325C, 330C, 330C L...
307, 311, 311B, 311C, 311D LRR, 312B, 312C, 312C L, 312D, 312D L, 313D, 314C, 314D CR, 314D LCR, 315D L, 318C, 318D L, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D FM, 3...
311C, 311D LRR, 311F LRR, 312C L, 312D, 312D L, 312D2, 312D2 L, 312E, 312E L, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 316E L, 318C, 318D2 L, 318E L, 319D L, 320C, 320C FM, 320C L, 320D, 320D FM, 3...
311C, 311D LRR, 312C, 312C L, 312D, 312D L, 313D, 314C, 314D CR, 314D LCR, 315D L, 318C, 318D L, 319C, 319D, 319D L, 319D LN, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN...
315D L, 318E L, 319D, 319D L, 319D LN, 320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321D LCR, 323D L, 323D LN, 323D2 ...
215B, 225, 227, 229, 320B, 321B, 322B L, 322B LN, 325, 325 LN, 325B, 325B L, 5130, 5130B, 5230, 539, 554, 574, 623E, 623F, 988F, 988F II, D11R, D6H, D6H XL, D6H XR, D6R, D7R, D8N, D8R, E300B, FB221, M...
320 L, 320B, 320B FM LL, 320C, 320C FM, 320D, 320D FM, 320D FM RR, 322B L, 322C FM, 323D LN, 323D SA, 324D FM, 324D FM LL, 325, 325 L, 325 LN, 325B, 325B L, 325C, 325D, 325D L, 329D, 329D L, 329D LN, ...
120M, 120M 2, 12M, 12M 2, 12M 3, 12M 3 AWD, 140M, 140M 2, 140M 3, 140M 3 AWD, 160M, 160M 2, 160M 3, 160M 3 AWD, 320C, 320D L, 321C, E110, E120, E120B, E140, E180, E240, E240C, E70, E70B, EL240, EL240B
2095953
NUT
314C
314C
1961522
NUT
308C, 308D, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 321C, 321D LCR, 325C, 328D LCR
308C, 308D, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 321C, 321D LCR, 325C, 328D LCR
2070235
NUT AS
308C, 308D, 314C, 314D LCR, 321C, 321D LCR, 325C, 328D LCR
308C, 308D, 314C, 314D LCR, 321C, 321D LCR, 325C, 328D LCR
0854771
NUT
308C, 311, 311B, 312B, 314C, 315, 315B, 320 L, 320B, 320N, E110B, E120B
308C, 311, 311B, 312B, 314C, 315, 315B, 320 L, 320B, 320N, E110B, E120B
308C
5I5152
NUT
311, 311B, 311C, 312B, 320 L, 320B, 320B FM LL, E200B
311, 311B, 311C, 312B, 320 L, 320B, 320B FM LL, E200B
1992220
NUT
302.5C, 303, 304
302.5C, 303, 304
1404722
NUT
301.6C, 312C, 312D2, 312D2 GC, 312D2 L, 313D2, 313D2 LGP, 314D CR, 314D LCR, 315C, 318C, 318D2 L, 319C, D3K XL, D4K XL, D5K LGP, D5N, D5R LGP, D6K, D6K LGP, D6K2, D6K2 LGP, D6N, D6N LGP, PL61
301.6C, 312C, 312D2, 312D2 GC, 312D2 L, 313D2, 313D2 LGP, 314D CR, 314D LCR, 315C, 318C, 318D2 L, 319C, D3K XL, D4K XL, D5K LGP, D5N, D5R LGP, D6K, D6K LGP, D6K2, D6K2 LGP, D6N, D6N LGP, PL61
0964878
NUT
318C, 319C, 320 L, 320C, 320C FM, 320C L, 321C, 322C, 324D FM, 324D FM LL, 324D L, 325C, 325C FM, 966H, E180, E200B, E240, E240C, EL240B, M325C MH
318C, 319C, 320 L, 320C, 320C FM, 320C L, 321C, 322C, 324D FM, 324D FM LL, 324D L, 325C, 325C FM, 966H, E180, E200B, E240, E240C, EL240B, M325C MH
1563103
NUT
318C, 319C, 320B U, 320C, 320C FM, 320C L, 320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 321C, 321D LCR, 323D L, 323D LN, 323D SA
318C, 319C, 320B U, 320C, 320C FM, 320C L, 320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 321C, 321D LCR, 323D L, 323D LN, 323D SA
318C, 319C, 320C, 320C FM
311D LRR, 312C, 312C L, 312D, 312D L, 313D, 314D CR, 314D LCR, 315C, 315D L, 318C, 318D L, 319C, 319D, 319D L, 319D LN, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D...