IT5911 NUT Caterpillar parts D7R NUT
Rating:
Alternative (cross code) number:
CAIT5911
IT-5911
IT5911
CAIT5911
IT-5911
IT5911

Buy NUT IT5911 Caterpillar genuine, new aftermarket tractor parts with delivery
TRACK-TYPE TRACTOR,
Compatible equipment models: IT5911:
TRACK-TYPE TRACTOR D7R
Caterpillar
Information:
Removal Procedure
Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
A     124-2946     Lifting Bracket     1    Start By:
Remove the variable valve actuator.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g03857624
Valve rocker arms and unit injector rocker arms can move on the shaft after the bolts have been removed. The shaft should be kept level when removed from the cylinder head. To avoid possible personal injury, keep fingers clear of the valve rocker arms and the unit injector rocker arms when lifting the assembly from the cylinder head.
Remove bolts (2) .
Use Tooling (A) to remove rocker arm shaft assembly (4) , valve rocker arms (3) , and electronic unit injector rocker arms (1) as a unit.Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 2 g03857616
Illustration 3 g03857618
Valve rocker arms and unit injector rocker arms can move on the shaft after the bolts have been removed. The shaft should be kept level when removed from the cylinder head. To avoid possible personal injury, keep fingers clear of the valve rocker arms and the unit injector rocker arms when lifting the assembly from the cylinder head.
Position rocker arm shaft assembly (4) , valve rocker arms (3) , and electronic unit injector rocker arms (1) as a unit with Tooling (A) on the cylinder head.Note: Apply clean engine oil to the underside of the bolt heads prior to installation.
Install bolts (2) and tighten in the following sequence: 2, 3, 1, 4 to a torque of 55 5 N m (41 4 lb ft). Tighten bolts (2) in the same sequence again to a torque of 55 5 N m (41 4 lb ft). Turn bolts (2) in the same sequence for an additional 60 5 degrees.
Adjust the electronic unit injectors. Refer to Testing and Adjusting, "Electronic Unit Injector - Adjust".
Adjust the engine valve lash. Refer to Testing and Adjusting, "Engine Valve Lash - Inspect/Adjust".End By: Install the variable valve actuator.
Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
A     124-2946     Lifting Bracket     1    Start By:
Remove the variable valve actuator.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g03857624
Valve rocker arms and unit injector rocker arms can move on the shaft after the bolts have been removed. The shaft should be kept level when removed from the cylinder head. To avoid possible personal injury, keep fingers clear of the valve rocker arms and the unit injector rocker arms when lifting the assembly from the cylinder head.
Remove bolts (2) .
Use Tooling (A) to remove rocker arm shaft assembly (4) , valve rocker arms (3) , and electronic unit injector rocker arms (1) as a unit.Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 2 g03857616
Illustration 3 g03857618
Valve rocker arms and unit injector rocker arms can move on the shaft after the bolts have been removed. The shaft should be kept level when removed from the cylinder head. To avoid possible personal injury, keep fingers clear of the valve rocker arms and the unit injector rocker arms when lifting the assembly from the cylinder head.
Position rocker arm shaft assembly (4) , valve rocker arms (3) , and electronic unit injector rocker arms (1) as a unit with Tooling (A) on the cylinder head.Note: Apply clean engine oil to the underside of the bolt heads prior to installation.
Install bolts (2) and tighten in the following sequence: 2, 3, 1, 4 to a torque of 55 5 N m (41 4 lb ft). Tighten bolts (2) in the same sequence again to a torque of 55 5 N m (41 4 lb ft). Turn bolts (2) in the same sequence for an additional 60 5 degrees.
Adjust the electronic unit injectors. Refer to Testing and Adjusting, "Electronic Unit Injector - Adjust".
Adjust the engine valve lash. Refer to Testing and Adjusting, "Engine Valve Lash - Inspect/Adjust".End By: Install the variable valve actuator.
Caterpillar parts catalog:
Parts nut Caterpillar catalog:
1376654
NUT
D7G
D7G
5A8027
NUT
D7G
D7G
3J3680
NUT
527
527
6G4701
NUT-BEARING
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 12G, 12H, 12H ES, 12H NA, 12K, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 160G, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 12G, 12H, 12H ES, 12H NA, 12K, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 160G, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA
6G4702
NUT
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 135H, 135H NA
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 135H, 135H NA
8X2092
NUT
120G, 12G, 130G, 140G, 160G, 16G
120G, 12G, 130G, 140G, 160G, 16G
0093161
NUT
120G, 12G, 130G, 140G, 14G, 160G, 16G
120G, 12G, 130G, 140G, 14G, 160G, 16G
5B9097
NUT
D7G
D7G