0951611 O-RING Caterpillar parts
E300, E300B, E450
Rating:
Alternative (cross code) number:
CA0951611
095-1611
0951611
CA0951611
095-1611
0951611
Weight: 0.01 pounds 0 kg.
Information:
CROSS SECTION DIAMETER
3.5
mm
ID
48.7
mm
MATERIAL
Nitrile (NBR) Rubber 90 Duro
OD
0
mm
EXCAVATOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
ITM Engine Components 09-51611 Exhaust Manifold Gasket
ITM Engine Components
ITM Engine Components
$30.35
10 Sep 2022
1.17[0.53] Pounds
US: Autoplicity ✅
ITM Engine Components 09-51611 Exhaust Manifold Gasket
ITM Engine Components
ITM Engine Components
$27.03
20 May 2021
1.17[0.53] Pounds
US: Autoplicity ✅
ITM Engine Components 09-51611 Exhaust Manifold Gasket
ITM Engine Components Comes with full brand warranty || Fits multiple makes and models (contact seller with your vehicle for fitment compatibility information)
ITM Engine Components Comes with full brand warranty || Fits multiple makes and models (contact seller with your vehicle for fitment compatibility information)
Number on catalog scheme:
26
For full view, you need register
Information:
Removal Procedure
Do not disconnect the air lines until the air pressure in the system is at zero. If hose is disconnected under pressure it can cause personal injury.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Remove the air pressure from the air tank and drain the coolant from the cooling system.
Illustration 1 g00484206
Typical example
Disconnect hose assemblies (1), (2) and (9) from the air compressor. Remove tube assembly (4) from the air compressor.
Remove bolt (5) and the washer. Remove clamp (7) from tube assembly for the breather. Move the tube assembly for the breather aside.
Remove bolts (3) and the washers that hold the air compressor to the timing gear housing.
Remove bolts (6) and remove air compressor (8) and the gasket from the engine. Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 4C-4030 Thread Lock Compound 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Check the condition of the gaskets and O-ring seals. If gaskets or O-ring seals are damaged, use new parts for replacement.
Illustration 2 g00484206
Typical example
Use bolts (3) and the washers to install air compressor (8). Apply Tooling (A) to the threads of bolts (6). Torque bolts (6) to 160 30 N m (118 22 lb ft).
Install clamp (7) for the tube assembly for the breather with bolt (5) and the washer.
Install tube assembly (4) and connect hose assemblies (9), (2) and (1) to air compressor (8).
Do not disconnect the air lines until the air pressure in the system is at zero. If hose is disconnected under pressure it can cause personal injury.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Remove the air pressure from the air tank and drain the coolant from the cooling system.
Illustration 1 g00484206
Typical example
Disconnect hose assemblies (1), (2) and (9) from the air compressor. Remove tube assembly (4) from the air compressor.
Remove bolt (5) and the washer. Remove clamp (7) from tube assembly for the breather. Move the tube assembly for the breather aside.
Remove bolts (3) and the washers that hold the air compressor to the timing gear housing.
Remove bolts (6) and remove air compressor (8) and the gasket from the engine. Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 4C-4030 Thread Lock Compound 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Check the condition of the gaskets and O-ring seals. If gaskets or O-ring seals are damaged, use new parts for replacement.
Illustration 2 g00484206
Typical example
Use bolts (3) and the washers to install air compressor (8). Apply Tooling (A) to the threads of bolts (6). Torque bolts (6) to 160 30 N m (118 22 lb ft).
Install clamp (7) for the tube assembly for the breather with bolt (5) and the washer.
Install tube assembly (4) and connect hose assemblies (9), (2) and (1) to air compressor (8).
Caterpillar parts catalog:
Parts o Caterpillar catalog:
0962846
O-RING
E300
E300
0942502
O-RING
E300, E300B
E300, E300B
0931367
O-RING
E300, E300B, E450
E300, E300B, E450
0931350
O-RING
E240
E240
0939585
O-RING
E300, E450, E650
E300, E450, E650
0945759
O-RING
E450, E650
E450, E650
0942946
O-RING
E300
E300
E300
0940652
O-RING
E300
E300
0962986
O-RING
E300
E300
0962971
O-RING
E300, E450
E300, E450
0955482
O-RING
E300, E300B
E300, E300B