1990700 O-RING-OUTER Caterpillar parts
414E, 416E, 416F, 420E, 420F, 422E, 422F, 428E, 428F, 430E, 430F, 432E, 432F, 434E, 434F, 442E, 444E, 444F, TH103, TH460B, TH560B, TH580B
Rating:
Alternative (cross code) number:
CA1990700
199-0700
1990700
CA1990700
199-0700
1990700
Weight: 0.04 pounds 0 kg.
BACKHOE LOADER, TELEHANDLER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
1990700 Seal O Ring (New AFTERMARKET) - G&T Engine Parts
G&T Engine Parts Fits equipment: BACKHOE LOADER: 414E, 416E, 420E, 422E, 428E, 430E, 432E, 434E, 442E, 444E, 434F, 444F2, 432F, 430F, 430F2, 420F, 416F2, 444F, 420F2, 428F2, 432F2, 428F, 416F, 415F2, 434F2, 427F2, 422F2, 422F. || Condition: NEW AFTERMARKET || Weight: 0.44 lbs || Use of any OEM manufacturer name is not intended to represent any relationship between the two companies, instead it indicates that we sell replacement parts that are compatible with OEM components.
G&T Engine Parts Fits equipment: BACKHOE LOADER: 414E, 416E, 420E, 422E, 428E, 430E, 432E, 434E, 442E, 444E, 434F, 444F2, 432F, 430F, 430F2, 420F, 416F2, 444F, 420F2, 428F2, 432F2, 428F, 416F, 415F2, 434F2, 427F2, 422F2, 422F. || Condition: NEW AFTERMARKET || Weight: 0.44 lbs || Use of any OEM manufacturer name is not intended to represent any relationship between the two companies, instead it indicates that we sell replacement parts that are compatible with OEM components.
RAParts 1990700 New Outer O Ring Fits Caterpillar Industrial Construction Models
Reliable Aftermarket Parts One New Aftermarket Replacement Outer O Ring Fits Various Fits Caterpillar Industrial Construction M || OEM Numbers Are Provided for Reference Only. Please Verify Fit Prior To Ordering. || Please Note: Some Listings Use Stock Images for Reference and May Differ from the Actual Product. || This Aftermarket Part Is Made to Meet or Exceed Manufacturer (OEM) Specifications. || All OEM part numbers and logos are to be used for identification purposes only.
Reliable Aftermarket Parts One New Aftermarket Replacement Outer O Ring Fits Various Fits Caterpillar Industrial Construction M || OEM Numbers Are Provided for Reference Only. Please Verify Fit Prior To Ordering. || Please Note: Some Listings Use Stock Images for Reference and May Differ from the Actual Product. || This Aftermarket Part Is Made to Meet or Exceed Manufacturer (OEM) Specifications. || All OEM part numbers and logos are to be used for identification purposes only.
This part in 2 request:
Show.
This information for suppliers only!
2019-07-25
2019-06-21
Compatible equipment models: 1990700:
Information:
Caterpillar Fuel Injection Test Benches S/N 1-1300The 6V124 Drive Coupling Modification Kit can be installed on any Caterpillar Fuel Injection Test Bench with the above serial numbers. The new drive coupling is stronger and will give better service when testing the fuel injection pump and governor of the larger Caterpillar engines. This instruction gives the procedure needed for the installation of the new drive coupling modification kit as a replacement for the original drive coupling.Removal of Original Drive Coupling
(1) Disconnect the electrical power from the test bench. Remove the two rear panels. (2) Remove four screws (1), then remove shroud (2). (3) Remove rails (3), screw (4) and window (5). (4) Loosen socket head screw (6) and remove drive coupling (7). (5) At the rear of the test bench, remove bolt (8) and washer, then remove flywheel (9). [The weight of flywheel (9) is approximately 60 pounds (27).] (6) Loosen nuts (A), (B), (C) and (D). (The test bench shown has the support straps (10) from the J26794 Stabilizer Kit.) (7) Remove drive belt (11). If the test bench has a mechanical counter, disconnect (do not remove) drive belt (12) from pulley (13). If the test bench has a digital tachometer, remove bracket (14) and magnetic pick-up (15). (8) Remove the degree wheel. According to the model of the test bench, the degree wheel will be fastened to the shaft by one of the methods that follow: degree wheel (16) is fastened to the shaft with bolts (17) [some models have only two bolts (17)]; degree wheel (18) is fastened to the shaft with a split clamp, and the clamp screw must be loosened from behind panel (19). (9) Use forcing screws (20) to remove center bushing (21) and pulley (22). (10) Loosen two setscrews (23) and move bearing (24) into bearing housing (25). Loosen three bolts (26). For those test benches that have a digital tachometer, do not lose the three non-magnetic bolts (26). If they are lost or damaged, install only non-magnetic bolts of the same part number as a replacement. (11) Use the three S1615 Bolts (27) from the modification kit as forcing screws and put them in forcing screw holes (E) to break loose the flanged taper-lock bushing. (12) Loosen two setscrews (28) and use a soft hammer as shown to remove the shaft from the test bench. Remove bearing (29) from shaft (30).Installation of 6V124 Drive Coupling Modification Kit
Parts in the 6V124 Drive Coupling Modification Kit are as follows. (1) Put pulley (12) with taper lock bushing, in position as shown. The three bolts that fasten the taper lock bushing to pulley (12) must be loose, not tight. [For test benches that have a digital tachometer, the bolts that fasten the taper lock bushing to pulley (12) must be non-magnetic.] (2) Install bearing (13) on 6V132 Shaft (2) so face (A) of the bearing is flush (even) with face (B) of the shaft, then tighten setscrews (14). Install 6V128 Key (3) and
(1) Disconnect the electrical power from the test bench. Remove the two rear panels. (2) Remove four screws (1), then remove shroud (2). (3) Remove rails (3), screw (4) and window (5). (4) Loosen socket head screw (6) and remove drive coupling (7). (5) At the rear of the test bench, remove bolt (8) and washer, then remove flywheel (9). [The weight of flywheel (9) is approximately 60 pounds (27).] (6) Loosen nuts (A), (B), (C) and (D). (The test bench shown has the support straps (10) from the J26794 Stabilizer Kit.) (7) Remove drive belt (11). If the test bench has a mechanical counter, disconnect (do not remove) drive belt (12) from pulley (13). If the test bench has a digital tachometer, remove bracket (14) and magnetic pick-up (15). (8) Remove the degree wheel. According to the model of the test bench, the degree wheel will be fastened to the shaft by one of the methods that follow: degree wheel (16) is fastened to the shaft with bolts (17) [some models have only two bolts (17)]; degree wheel (18) is fastened to the shaft with a split clamp, and the clamp screw must be loosened from behind panel (19). (9) Use forcing screws (20) to remove center bushing (21) and pulley (22). (10) Loosen two setscrews (23) and move bearing (24) into bearing housing (25). Loosen three bolts (26). For those test benches that have a digital tachometer, do not lose the three non-magnetic bolts (26). If they are lost or damaged, install only non-magnetic bolts of the same part number as a replacement. (11) Use the three S1615 Bolts (27) from the modification kit as forcing screws and put them in forcing screw holes (E) to break loose the flanged taper-lock bushing. (12) Loosen two setscrews (28) and use a soft hammer as shown to remove the shaft from the test bench. Remove bearing (29) from shaft (30).Installation of 6V124 Drive Coupling Modification Kit
Parts in the 6V124 Drive Coupling Modification Kit are as follows. (1) Put pulley (12) with taper lock bushing, in position as shown. The three bolts that fasten the taper lock bushing to pulley (12) must be loose, not tight. [For test benches that have a digital tachometer, the bolts that fasten the taper lock bushing to pulley (12) must be non-magnetic.] (2) Install bearing (13) on 6V132 Shaft (2) so face (A) of the bearing is flush (even) with face (B) of the shaft, then tighten setscrews (14). Install 6V128 Key (3) and
Cat SIS web machinery list:
Parts o Caterpillar catalog:
1167130
O-RING
3054, 3056, 307, 312, 416B, 416C, 426B, 426C, 428B, 428C, 436B, 436C, 438B, 438C, AP-800C, BG-225B, CB-434B, CB-434C, CB-534B, CB-534C, CB-535B, CB-544, CB-545, CP-433C, CS-323C, CS-431C, PS-150B, PS-...
3054, 3056, 307, 312, 416B, 416C, 426B, 426C, 428B, 428C, 436B, 436C, 438B, 438C, AP-800C, BG-225B, CB-434B, CB-434C, CB-534B, CB-534C, CB-535B, CB-544, CB-545, CP-433C, CS-323C, CS-431C, PS-150B, PS-...
1990759
O-RING-INNER
414E, 416E, 416F, 420E, 420F, 422E, 422F, 428E, 428F, 430E, 430F, 432E, 432F, 434E, 434F, 442E, 444E, 444F, TH103, TH460B, TH560B, TH580B
414E, 416E, 416F, 420E, 420F, 422E, 422F, 428E, 428F, 430E, 430F, 432E, 432F, 434E, 434F, 442E, 444E, 444F, TH103, TH460B, TH560B, TH580B
1990759
O-RING-INNER
414E, 416E, 416F, 420E, 420F, 422E, 422F, 428E, 428F, 430E, 430F, 432E, 432F, 434E, 434F, 442E, 444E, 444F, TH103, TH460B, TH560B, TH580B
414E, 416E, 416F, 420E, 420F, 422E, 422F, 428E, 428F, 430E, 430F, 432E, 432F, 434E, 434F, 442E, 444E, 444F, TH103, TH460B, TH560B, TH580B
1167134
O-RING
416B, 426B, 428B, CB-534B
416B, 426B, 428B, CB-534B
1167130
O-RING
3054, 3056, 307, 312, 416B, 416C, 426B, 426C, 428B, 428C, 436B, 436C, 438B, 438C, AP-800C, BG-225B, CB-434B, CB-434C, CB-534B, CB-534C, CB-535B, CB-544, CB-545, CP-433C, CS-323C, CS-431C, PS-150B, PS-...
3054, 3056, 307, 312, 416B, 416C, 426B, 426C, 428B, 428C, 436B, 436C, 438B, 438C, AP-800C, BG-225B, CB-434B, CB-434C, CB-534B, CB-534C, CB-535B, CB-544, CB-545, CP-433C, CS-323C, CS-431C, PS-150B, PS-...
8Q2820
O. RING
RT100, RT50
RT100, RT50
8Q5348
O RING
RT100, RT50
RT100, RT50
8Q2136
O RING
RT100
RT100
8Q2740
O. RING
RT100
RT100
8Q2075
O. RING
RT100
RT100
6R8974
O. RING
RT100
RT100