3716009 OEM AR-MOBILE HYD POWER UNIT Caterpillar parts
349D L
Rating:
Alternative (cross code) number:
CA3716009
371-6009
3716009
CA3716009
371-6009
3716009
MOBILE HYD POWER UNIT,
Compatible equipment models: 3716009:
For full view, you need register
Information:
Introduction
The following procedure will explain the steps for adjusting the front axle toe-in.Before you perform this adjustment, refer to Testing and Adjusting, "Machine Preparation".Required Tools
Table 1
Tool Part Number Description Qty
F 1U-9366 Automatic Tape Measure 1 Adjustment Preparation
Move the machine to a smooth horizontal location.
Chock the wheels.
Lower all of the implements.
Raise the front wheels off the ground. Install the wheel lean locking bolt into the lean bar.Adjustment Procedure
Illustration 1 g01100244
Top view of the front axle
(1) Clamps
(2) Tie rod
(A) Distance
(B) Distance
Attach a short level with a magnetic base to the outside of each front wheel spindle or rim.
Rotate the tires until the levels are both horizontal. Mark a V on the front of each front tire at spindle height near the center of the tread.
With Tooling (F) measure the distance (A) between the V marks on each tire. Use the sharp point on the inside of each V for the measuring points.
Without touching the levels, rotate the tires so that the V marks are at the rear and the levels are again horizontal.
With Tooling (F) measure the distance (B) between the V marks.
Compare measurements (A) and (B). The toe-in is correct if measurement (A) at the front of the front tires is less than the measurement (B) at the rear of the front tires. Measurement (A) should be 6.0 3.0 mm (0.24 0.12 inch) smaller than measurement (B).
Adjust the toe-in, as needed. Loosen clamps (1) on tie rod (2). Rotate tie rod (2) in the direction that is need in order to achieve the correct toe-in for the front wheels. When the toe-in adjustment is correct, orient clamps (1), as shown. Tighten clamps (1) to the specified torque.
The following procedure will explain the steps for adjusting the front axle toe-in.Before you perform this adjustment, refer to Testing and Adjusting, "Machine Preparation".Required Tools
Table 1
Tool Part Number Description Qty
F 1U-9366 Automatic Tape Measure 1 Adjustment Preparation
Move the machine to a smooth horizontal location.
Chock the wheels.
Lower all of the implements.
Raise the front wheels off the ground. Install the wheel lean locking bolt into the lean bar.Adjustment Procedure
Illustration 1 g01100244
Top view of the front axle
(1) Clamps
(2) Tie rod
(A) Distance
(B) Distance
Attach a short level with a magnetic base to the outside of each front wheel spindle or rim.
Rotate the tires until the levels are both horizontal. Mark a V on the front of each front tire at spindle height near the center of the tread.
With Tooling (F) measure the distance (A) between the V marks on each tire. Use the sharp point on the inside of each V for the measuring points.
Without touching the levels, rotate the tires so that the V marks are at the rear and the levels are again horizontal.
With Tooling (F) measure the distance (B) between the V marks.
Compare measurements (A) and (B). The toe-in is correct if measurement (A) at the front of the front tires is less than the measurement (B) at the rear of the front tires. Measurement (A) should be 6.0 3.0 mm (0.24 0.12 inch) smaller than measurement (B).
Adjust the toe-in, as needed. Loosen clamps (1) on tie rod (2). Rotate tie rod (2) in the direction that is need in order to achieve the correct toe-in for the front wheels. When the toe-in adjustment is correct, orient clamps (1), as shown. Tighten clamps (1) to the specified torque.