AVSPARE.COM
parts catalog

OPTION AR-HYDRAULIC 3966753 - Caterpillar



3966753 OPTION AR-HYDRAULIC Caterpillar parts 314D LCR OPTION
Rating:
32
Alternative (cross code) number:
CA3966753
396-6753
3966753
Caterpillar 3966753 OPTION AR-HYDRAULIC

Buy OPTION AR-HYDRAULIC 3966753 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR,

Compatible equipment models: 3966753:

EXCAVATOR  314D LCR   Caterpillar
  For full view, you need register

Information:


Illustration 1 g01102552
Note: The rotation of the blade needs to be perpendicular within 5 degrees. Ensure that the alignment arrows on the circle are aligned.
Adjust both sides of the blade upward in order to allow the blade to have approximately 304.80 mm (1.00 ft) of movement.
Press the menu key (6) .
Illustration 2 g01311325
Press and release the following keys at the same time in order to enter the "Installation" menu:
"ESC/Left Reset/Left Bench" key (13)
Right Side Down Arrow Key (7)
Increment Key (10)
Illustration 3 g01305040
Use the arrow keys (1) in order to select "Auto Valve Calibration" from the "Calibration" menu.
Press the "OK/right reset" key (8). This causes the "Calibration" menu to be shown on the LCD of the display.
Illustration 4 g01305042
Press the arrow keys (1) in order to select "Auto Valve Calibration" from the "Calibration" menu.
Press the "OK/right reset" key (8) in order to enter the "Auto Valve Calibration" menu.
Illustration 5 g01311659
Use the arrow keys (1) in order to select the "<- Auto Valve Calibration" for the lift valve. Press the "OK/right reset" key (8) .
Set the lower limit of the blade.When this screen is displayed, the user must set a valid LOWER calibration limit.
Illustration 6 g01304912
(51) Laser Strike Limit (52) Laser Strike Indicator
Use the machine's control lever in order to lower the blade until the laser strike indicator (52) is within the valid limit range (51). Once a valid limit is achieved "OK" will be shown in the lower right of the "<- Auto Valve Calibration" message screen.
Press the "OK/right reset" key (8) in order to continue.Note: The user must successfully set the lower limit before continuing to the next screen. You can press any switch on the display except the "OK/right reset" key (8) and the arrow keys (1) in order to abort the automatic valve calibration. The "Exit-Error" screen is displayed with the text "Abort" when you abort the calibration. If an error is detected, the "Exit-Error" Screen is displayed. The possible causes of errors are listed below:
No Sensor Information
Limit Measurement too close to sensor rail.
Unstable Laser Transmitter
Set the upper limit.
Illustration 7 g01311606
(51) Laser Strike Limit (52) Laser Strike Indicator
Use the machine's control lever in order to raise the blade until the laser strike indicator (52) is within the valid limit range (51). Once a valid limit is achieved "OK" will be shown in the lower right of the "<- Auto Valve Calibration" message screen.
Press the "OK/right reset" key (8) in order to continue.Note: The user must successfully set the upper limit before continuing to the next screen. You can press any switch on the display except the "OK/right reset" key (8) and the arrow keys (1) in order to abort the automatic valve calibration. The "Exit-Error" screen is displayed with the text "Abort" when you abort the calibration. If an error is detected, the "Exit-Error" Screen is displayed. The possible causes of errors are listed below:
No Sensor Information
Limit Measurement too close to sensor rail.
Unstable Laser Transmitter
Illustration 8 g01305052
Confirm the start of the calibration.
Illustration 9 g01305054
Illustration 10 g01305055
Press the "OK/right reset" key (8) in order to begin

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts option Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.