AVSPARE.COM
parts catalog

OPTION AR-HYDRAULIC 3966754 - Caterpillar



3966754 OPTION AR-HYDRAULIC Caterpillar parts 314D LCR OPTION
Rating:
33
Alternative (cross code) number:
CA3966754
396-6754
3966754
Caterpillar 3966754 OPTION AR-HYDRAULIC

Buy OPTION AR-HYDRAULIC 3966754 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR,

Compatible equipment models: 3966754:

EXCAVATOR  314D LCR   Caterpillar
  For full view, you need register

Information:


Illustration 23 g01189994
6-Pin Socket Connector
Measure the resistance between the contacts that are listed in Table 10.
Table 10
6-Pin Socket Connector (Mast End)    6-Pin Socket Connector (LR End)    Resistance    
A    A    Less than 5 ohms    
F    F    Less than 5 ohms    
C     C     Less than 5 ohms    
D     D     Less than 5 ohms    Expected Result:All of the resistance measurements are less than 5 ohm.Results:
OK - All of the resistance measurements are less than 5 ohm.Repair: The laser receiver or the single adapter has failed. Use a known good laser receiver and single adapter to verify which of the two components have failed.STOP
NOT OK - All of the resistance measurements are greater than 5000 ohms. The coil cable has failed.Repair: Replace the coil cable.STOPTest Step 15. CHECK THE VOLTAGE AT THE ELECTRIC MAST
Disconnect the cable at the base of the electric mast.
Turn the disconnect switch and the disconnect switch to the ON position.
Turn the key start switch and the disconnect switch to the ON position.
Disconnect the harness connector (6) from the electronic control (3) .
Illustration 24 g01189993
10-Pin Connector
Check for machine voltage between the following contacts on the 10-pin connector for the electric mast that are listed in Table 11.
Table 11
10-Pin Connector Contacts    10-Pin Connector Contacts    Voltage    
A         Approximately machine voltage.    
H     F     Approximately machine voltage.    Expected Result:The voltage is approximately machine voltage.Results:
YES - The voltage is approximately machine voltage. Proceed to Test Step 18.
NO - The voltage is not machine voltage. Proceed to Test Step 16.Test Step 16. CHECK FOR VOLTAGE AT THE KNUCKLE CONNECTORS
Disconnect the coil cable from the knuckle connector.
Illustration 25 g01189993
10-Pin Connector
Check for machine voltage at the knuckle connector contacts that are listed in Table 12.
Table 12
10-Pin Connector Contacts    10-Pin Connector Contacts    Voltage    
A     F     Approximately machine voltage.    
H     F     Approximately machine voltage.    Expected Result:The voltage is approximately machine voltage.Results:
YES - The voltage is approximately machine voltage. The coil cable has failed.Repair: Replace the coiled cable.STOP
NO - The voltage is not machine voltage. Proceed to Test Step 17.Test Step 17. CHECK FOR VOLTAGE AT THE POWER MODULE
Disconnect the coil cable from the power supply module.
Turn the key start switch to the ON position.
Check for machine voltage at the connector contacts that are listed in Table 13.
Table 13
Power Module Contact    Power Module Contact    Voltage    
B     F     Approximately machine voltage.    
D     F     Approximately machine voltage.    
H     F     Approximately machine voltage.    Expected Result:The voltage is approximately machine voltage.Results:
YES - The voltage is approximately machine voltage. The AccuGrade harness has failed.Repair: Replace the AccuGrade harness or repair the AccuGrade harness.STOP
NO - The voltage is not machine voltage.Repair: Replace the power supply module.STOPTest Step 18. CHECK THE CAN DATA LINK CIRCUIT
The key start switch and the disconnect switch remain in the OFF position.
Measure the resistance across contact C and contact

Caterpillar SIS machinery equipment:

Caterpillar SIS


Parts option Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.