3T7726 ORIFICE Caterpillar parts
613C, 615, 615C, 926, 950B, 966D, 980C, D4H, G936, IT28
Rating:
Alternative (cross code) number:
CA3T7726
3T-7726
3T7726
CA3T7726
3T-7726
3T7726
Weight: 0.06 pounds 0 kg.
INTEGRATED TOOLCARRIER, WHEEL TRACTOR,
Compatible equipment models: 3T7726:
Information:
1. Make an adjustment to tooling (B) until the height is approximately 42.5 in. (108 cm). Make an adjustment to tooling (C) until the height is 28.5 in. (72.4 cm).
To avoid personal injury, keep away from the area of the machine when it is driven up on tooling (A) at the front of the machine and the rear of the machine. Tooling (A) can come out from under the tracks with force if it is not installed correctly.
2. Put tooling (A) at the rear of the machine as shown. Start the machine and move it to the rear and up on tooling (A). Put tooling (C) in position under the bevel gear case. The weight of the rear of the machine will not be on tooling (C) until the front of the machine is lifted with tooling (A). Put tooling (A) in position in front of the machine. Move the machine slowly forward and up on tooling (A). As the front of the machine goes up the rear of the machine will come down on tooling (C). Lift the front of the machine until tooling (B) can be installed under the radiator guard and main frame of the machine as shown. Tooling (A) at the rear of the machine will be free to remove from under the tracks. Move both tracks to the rear until tooling (A) is free at the front of the machine. 3. Remove two guard assemblies (1) and (2).4. Put the recoil spring under compression as follows: a) Put a slug (3) that is 3 in. (76.2 mm) in diameter and 2.5 in. (63.5 mm) long in the sprocket segment as shown. Start the machine and move it to the rear slowly. Make sure when the slug makes contact with the track, it makes contact with a bushing as shown.b) As the machine is moved to the rear with the slug in position, the recoil spring will be put under compression.c) Move the machine until the front pilot of the recoil spring assembly is approximately .125 in. (3.2 mm) away from the stops that are fastened to the track roller frame. d) Remove bolt (4) and washer (6). Tighten nut (5) by hand to hold the recoil spring in a shorter position. Move the machine forward slowly and remove the slug from the sprocket.5. Install guards (1) and (2) back on the machine.6. Make a separation of the track. See Separation of Tracks. 7. Remove guard assemblies (7) and (8) from the track roller frame. 8. Remove four bolts (9) and nuts that hold the cylinder to the yoke. Pull the front idler and yoke forward on the track roller frame. 9. Remove hydraulic track adjuster (10) from the recoil spring assembly. 10. Remove O-ring seal (11) from the front pilot of the recoil spring assembly.Install Hydraulic Track Adjuster
1. Install a new O-ring seal (1) in the front pilot of the recoil spring assembly. Put 1P808 General Purpose Lubricant on the seal. 2.
To avoid personal injury, keep away from the area of the machine when it is driven up on tooling (A) at the front of the machine and the rear of the machine. Tooling (A) can come out from under the tracks with force if it is not installed correctly.
2. Put tooling (A) at the rear of the machine as shown. Start the machine and move it to the rear and up on tooling (A). Put tooling (C) in position under the bevel gear case. The weight of the rear of the machine will not be on tooling (C) until the front of the machine is lifted with tooling (A). Put tooling (A) in position in front of the machine. Move the machine slowly forward and up on tooling (A). As the front of the machine goes up the rear of the machine will come down on tooling (C). Lift the front of the machine until tooling (B) can be installed under the radiator guard and main frame of the machine as shown. Tooling (A) at the rear of the machine will be free to remove from under the tracks. Move both tracks to the rear until tooling (A) is free at the front of the machine. 3. Remove two guard assemblies (1) and (2).4. Put the recoil spring under compression as follows: a) Put a slug (3) that is 3 in. (76.2 mm) in diameter and 2.5 in. (63.5 mm) long in the sprocket segment as shown. Start the machine and move it to the rear slowly. Make sure when the slug makes contact with the track, it makes contact with a bushing as shown.b) As the machine is moved to the rear with the slug in position, the recoil spring will be put under compression.c) Move the machine until the front pilot of the recoil spring assembly is approximately .125 in. (3.2 mm) away from the stops that are fastened to the track roller frame. d) Remove bolt (4) and washer (6). Tighten nut (5) by hand to hold the recoil spring in a shorter position. Move the machine forward slowly and remove the slug from the sprocket.5. Install guards (1) and (2) back on the machine.6. Make a separation of the track. See Separation of Tracks. 7. Remove guard assemblies (7) and (8) from the track roller frame. 8. Remove four bolts (9) and nuts that hold the cylinder to the yoke. Pull the front idler and yoke forward on the track roller frame. 9. Remove hydraulic track adjuster (10) from the recoil spring assembly. 10. Remove O-ring seal (11) from the front pilot of the recoil spring assembly.Install Hydraulic Track Adjuster
1. Install a new O-ring seal (1) in the front pilot of the recoil spring assembly. Put 1P808 General Purpose Lubricant on the seal. 2.
Caterpillar parts catalog:
Parts orifice Caterpillar catalog:
2S1541
ORIFICE-JET
120B, 120G, 12E, 12G, 12H, 12H ES, 12H NA, 130G, 140B, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H NA, 1673B, 1673C, 1676, 215, 235, 235B, 235C, 330, 330 L, 330...
120B, 120G, 12E, 12G, 12H, 12H ES, 12H NA, 130G, 140B, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H NA, 1673B, 1673C, 1676, 215, 235, 235B, 235C, 330, 330 L, 330...
7G8271
ORIFICE-AIR
120G, 130G, 16G, 428, 517, 527, 613C, 615, 785, 933, 933C, 939, 939C, 943, 953, 953B, 963, 963B, 973, D10, D3C III, D4C III, D4H, D4H XL, D4HTSK III, D5C III, D5H, D5H XL, D5HTSK II, D6H, D6H XL, D6H ...
120G, 130G, 16G, 428, 517, 527, 613C, 615, 785, 933, 933C, 939, 939C, 943, 953, 953B, 963, 963B, 973, D10, D3C III, D4C III, D4H, D4H XL, D4HTSK III, D5C III, D5H, D5H XL, D5HTSK II, D6H, D6H XL, D6H ...
7N0817
ORIFICE-COOLING JET
215, 3204, 926, 943, 953, D4HTSK II, E180
215, 3204, 926, 943, 953, D4HTSK II, E180
4J1698
ORIFICE
245, 245B, 24H, 24M, 631C, 641, 641B, 651, 657, 776C, 776D, 777B, 777D, 777G, 824B, 834, 950F II, 960F, 966F II, 970F, 980F, 980F II, 988, D4H, R1300, R1600
245, 245B, 24H, 24M, 631C, 641, 641B, 651, 657, 776C, 776D, 777B, 777D, 777G, 824B, 834, 950F II, 960F, 966F II, 970F, 980F, 980F II, 988, D4H, R1300, R1600
9W9831
ORIFICE-SCREEN
814B, 815B, 816F, 826C, 834B, 836, 926, 936, 936F, 939, 950B, 950B/950E, 950F, 950F II, 960F, 966D, 966F, 966F II, 970F, 980C, 980F, 980F II, 980G, 980G II, 988B, D11N, D25C, D25D, D300B, D350E, D350E...
814B, 815B, 816F, 826C, 834B, 836, 926, 936, 936F, 939, 950B, 950B/950E, 950F, 950F II, 960F, 966D, 966F, 966F II, 970F, 980C, 980F, 980F II, 980G, 980G II, 988B, D11N, D25C, D25D, D300B, D350E, D350E...
7J9972
ORIFICE
920, 926, IT28
920, 926, IT28
9P9736
ORIFICE
793D, 793F, 793F CMD, 793F OEM, 793F-XQ, 910, 916, 926, IT18B, IT28, IT28B
793D, 793F, 793F CMD, 793F OEM, 793F-XQ, 910, 916, 926, IT18B, IT28, IT28B
9J9405
ORIFICE
950B, 950F, 950F II, 960F
950B, 950F, 950F II, 960F
9J9777
ORIFICE
966D, 966F, 966F II, 970F, AD30, D350E, D400E, R1300, R1300G, R1300G II
966D, 966F, 966F II, 970F, AD30, D350E, D400E, R1300, R1300G, R1300G II
9P5476
ORIFICE
966D, 980C, 988B, D10, D35HP, D400, D44B, D550B
966D, 980C, 988B, D10, D35HP, D400, D44B, D550B
3T7727
ORIFICE-SCREEN
910, 916, 931C, D10N, D3C, D5H, D6H, D8L
910, 916, 931C, D10N, D3C, D5H, D6H, D8L
8G7706
ORIFICE
943
943
8P7949
ORIFICE
931, D10
931, D10
9K6426
ORIFICE
561D, 826B, D5B
561D, 826B, D5B
9P0247
ORIFICE ASSEM.
955L, D5B, D6D
955L, D5B, D6D
3P2437
ORIFICE
777B, 941
777B, 941
2D8935
ORIFICE
621, 621B, 621R, 623, 627, 627B, 631C, 631E, 631G, 633E II, 637, 637D, 637E, 637G, 641, 641B, 650B, 651, 651E, 657, 657B, 657E, 666, 666B, 924K, 930K, 938K
621, 621B, 621R, 623, 627, 627B, 631C, 631E, 631G, 633E II, 637, 637D, 637E, 637G, 641, 641B, 650B, 651, 651E, 657, 657B, 657E, 666, 666B, 924K, 930K, 938K
3706346
ORIFICE AS
621F, 621G, 623G, 627G, 631E, 631G, 633E II, 637E, 637G, 651E, 657E, 657G, 770, 772, 773B, 773D, 773E, 775B, 775D, 775E, 784B, 784C, 785B, 785C, 785D, 789B, 789C, 789D, 793B, 793D
621F, 621G, 623G, 627G, 631E, 631G, 633E II, 637E, 637G, 651E, 657E, 657G, 770, 772, 773B, 773D, 773E, 775B, 775D, 775E, 784B, 784C, 785B, 785C, 785D, 789B, 789C, 789D, 793B, 793D
3706345
ORIFICE AS
621F, 621G, 623G, 627G, 631E, 631G, 633E II, 637E, 637G, 651E, 657E, 657G, 769C, 769D, 770, 771C, 771D, 772, 773B, 773D, 773E, 775B, 775D, 775E, 776D, 777D, 784B, 784C, 785B, 785C, 785D, 789B, 789C, 7...
621F, 621G, 623G, 627G, 631E, 631G, 633E II, 637E, 637G, 651E, 657E, 657G, 769C, 769D, 770, 771C, 771D, 772, 773B, 773D, 773E, 775B, 775D, 775E, 776D, 777D, 784B, 784C, 785B, 785C, 785D, 789B, 789C, 7...
3706344
ORIFICE AS
621F, 621G, 623G, 627G, 651E, 657E, 657G, 769C, 769D, 770, 771C, 771D, 772, 773B, 773D, 773E, 775B, 775D, 775E, 776D, 777D, 784B, 784C, 785B, 785C, 785D, 789B, 789C, 789D, 793B, AD45B, AD55, D400E II
621F, 621G, 623G, 627G, 651E, 657E, 657G, 769C, 769D, 770, 771C, 771D, 772, 773B, 773D, 773E, 775B, 775D, 775E, 776D, 777D, 784B, 784C, 785B, 785C, 785D, 789B, 789C, 789D, 793B, AD45B, AD55, D400E II
1248202
ORIFICE
D6R
D6R
8F4529
ORIFICE
977D
977D