AVSPARE.COM
parts catalog

OVERALL 0878397 - Caterpillar



0878397 OVERALL Caterpillar parts OVERALL
Rating:
86
Alternative (cross code) number:
CA0878397
087-8397
0878397
Caterpillar 0878397 OVERALL

Buy OVERALL 0878397 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Connect one Tool (A2) to each Tool (A3).
Connect each Tool (A3) to Tool (A1).
Table 4
Optional Tools(1)
Tool Item Qty Part No Description
B B1 2 8T-0855 Pressure Gauges
B2 2 6V-4144 Quick Connect Couplers
C C1 2 177-7860 Hose As
C2 2 6V-4142 Fittings
C3 2 6V-4143 Quick Connect Couplers
(1) The optional tools can be used to replace the digital pressure gauges in the required tool list.
Connect one Tool (B2) to each Tool (B1).
Connect each Tool (C3) to each Tool (C1). Connect each Tool (C2) to each Tool (C1).
Connect one Tool (C3) to each Tool (B2). Test Preparation
Drive the machine to a smooth, horizontal surface.
Illustration 2 g03425361
Move propel lever (4) to the NEUTRAL position.
Press parking brake switch (5) in order to change the status of the parking brake to "engaged". When the parking brake status is "engaged", LED (2) next to the parking brake switch will be illuminated.
Use travel mode switch (3) to select the PAVE mode. When the travel mode switch is set to PAVE mode, an LED next to PAVE symbol (1) will be illuminated. Note: The machine must be in PAVE mode in order to operate the screed lift system, the hopper system, the apron system and the auger lift system.
Illustration 3 g03428841
Press the down arrow on left hopper switch (6) and right hopper switch (7) to the LOWER position. Fully lower the hoppers.
Illustration 4 g03696716
Use screed float switch (10) to place the screed in the FLOAT position. When the screed is in the FLOAT position, an LED next to the screed float switch will illuminate. Lower the screed to the ground.
Press the down arrow on throttle control switch (11) once in order to operate the engine in low idle.
Illustration 5 g03428689
Shut off the engine. Either place machine power switch (12) in the OFF position or press and hold push to start switch (9) for 3 seconds. An LED next to the push to start switch will flash when the engine is in shutdown mode. Note: The engine may run for several minutes when placed in the shutdown mode.
If the engine was shut down using the push to start switch (9), move machine power switch (12) to the OFF position.
Illustration 6 g03428884
Unhook latches (14), open engine compartment cover (13).
Illustration 7 g03713056
Remove the cap from dual-purpose valve (15) of the generator cooling circuit filter.
Connect Tool (A2) to dual-purpose valve (15). Test Procedure
Place machine power switch (12) in the ON position.
Press push to start switch (9) for 2 seconds in order to start the engine. An LED next to the push to start switch will flash when the engine is in start mode. When the engine has started, the LED will remain illuminated. Note: Only one attempt to start the engine is allowed per key cycle. A new key cycle will need to be done in order to restart the process.
Operate the engine at low idle for a few minutes.
Press the up arrow on throttle control switch (11) in order to place the engine in high idle. The engine speed


Parts overall Caterpillar catalog:

0855784 OVERALL (L)
E110B, E120B, E200B, E450
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.