PAD AS 2133347 - Caterpillar

2133347 PAD AS Caterpillar parts 446B, 446D

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA2133347
213-3347
2133347

Weight: 0.39 pounds 0 kg.

Buy PAD AS 2133347 Caterpillar genuine, new aftermarket tractor parts with delivery
BACKHOE LOADER,

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

Walker Products 245-1078 Mass Air Flow Sensor Assembly

$82.44

13 Aug 2021
0.5[0.23] Pounds
US: B2C Auto Parts

Walker Products 245-1078 Mass Air Flow Sensor Assembly
Walker Products Walker Products Mass Air Flow (MAF) sensor measures the amount of air by weight through changing voltages or frequencies || MAF Sensor sends information collected to the onboard computer || The computer uses this and other inputs to calculate the correct amount of fuel delivered || Symptoms of failure MAF include poor starting, engine surging, engine stalling, a check engine light, and no-start conditions. Sensors are non-serviceable, replace sensors that are non-functional || OEM Part Number: 74-10020 4M-1074 SU5414 SU6308 19440 221000M MA131 213-3347 MF21029 MF21029 86-10020 MF21093 86073 5S2596 158-1259 5S2942 7R8 AF10165 19437 86-10020 59098 917-800 FDM783 MAS0334 FDM781 86265 V10-72-1070 157-0303 MF21085N MF21000 FDM955 20991 158-07775 221085M 64-1758 504-05 64-1787 157-0343 MF21085

Number on catalog scheme: 11

For full view, you need register

Compatible equipment models: 2133347:

BACKHOE LOADER 446B 446D Caterpillar

Information:

Illustration 1 g01197805
Schematic for the Cat Data LinkThis diagnostic code is recorded when the Implement ECM cannot communicate with the Caterpillar Monitoring System via the Cat Data Link. The update rate from the ECM is not correct.The possible causes for this diagnostic code are listed:
The data link wire between the implement ECM and the Caterpillar Monitoring System has failed.System Response:The machine response is listed:
All functions will be disabled. This is true only if the ECM has never been powered up.Note: Ensure that the diagnostic code is active.Test Step 1. CHECK THE COMPATIBILITY OF THE SOFTWARE.
For the correct software part numbers, refer to the Electronics Groups in the parts manual for the machine that is being serviced.Expected Result:The software is compatible.Results:
YES - The software is compatible. Proceed to Test Step 2.
NO - The software is not compatible.Repair: Flash the proper software to the appropriate ECM. Cycle the key switch in order to initialize the new software. Ensure that the diagnostic code is no longer active. If this repair does not resolve the problem, proceed to Test Step 2.Test Step 2. CHECK THE +BATTERY CIRCUIT AT THE ECM CONNECTORS.
Turn the disconnect switch to the OFF position.
Turn the key start switch to the OFF position.
Disconnect connector J1 from the ECM.
At the connector J1, measure the voltage between the possible sources of + battery and possible sources of ground.Expected Result:The voltage measures 18 DCV to 35 DCV.Results:
YES - The voltage measures 18 DCV to 35 DCV. The voltage is correct. Proceed to Test Step 3.
NO - The voltage measures less than 18 DCV.Repair: Ensure that there is a proper ground. Also, check the circuit breakers. If the ground is proper, the power circuit has failed. Repair the power circuit or replace the power circuit. The power circuit is contact 31 (wire 121-RD). If the problem is not resolved, then proceed to Test Step 4.Test Step 3. CHECK FOR A CAT DATA