AVSPARE.COM
parts catalog

PAD 3237250 - Caterpillar



3237250 PAD Caterpillar parts PAD
Rating:
16
Alternative (cross code) number:
CA3237250
323-7250
3237250
Caterpillar 3237250 PAD
Weight: 0.39 pounds 0 kg.

Buy PAD 3237250 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme: 3
 
  For full view, you need register

Information:


Inspect the condition of slave piston (17). The slave piston must be free of wear and score marks. Replace slave piston (17), if necessary.
Install slave piston (17), springs (16), spring retainer (14), and retaining ring (15) in the bore.
Place Tooling (C) over slave piston adjustment screw (13) and spring retainer (14). Turn the handle on Tooling (C) until spring retainer (14) is approximately 1.0 mm (0.04 inch) below the retaining ring groove. Install retaining ring (15) with Tooling (A) .
Remove Tooling (C) slowly in order to ensure that retaining ring (15) is properly seated in the groove.Note: Repeat Steps 4 through 7 for the remaining slave piston.
Illustration 7 g00523484
Screw in slave piston adjustment screw (13) until contact is made with the slave piston.
Illustration 8 g00523483
Install slave piston adjustment screw locknut (12) .Note: Repeat Steps 8 and 9 for the remaining slave piston adjustment screw.
Illustration 9 g00523482
Coat new O-ring seals (11) with clean engine oil. Install the upper O-ring seal and the center O-ring seal on solenoid valve (10). Install the small O-ring seal in the bottom of the bore in the compression brake housing.Note: Ensure that O-ring seals (11) are seated properly on solenoid valve (10). Do not twist the seals or unseat the seals during installation of the solenoid valve.
Illustration 10 g00523481
Carefully install solenoid valve (10) in the compression brake housing.There are two different designs of solenoid valves. The difference can be determined by the number of points on the head of the solenoid valve. Use the correct torque value for your solenoid valve. Tighten the solenoid valve with a twelve point head to the following torque. ... 12.5 N m (9 lb ft) Tighten the solenoid valve with a six point head to the following torque. ... 20 N m (15 lb ft)
Illustration 11 g00524781
Illustration 12 g00524780
Illustration 13 g00523476
Improper assembly of parts that are spring loaded can cause bodily injury.To prevent possible injury, follow the established assembly procedure and wear protective equipment.
Inspect the condition of control valve (9). Insert a wire into the hole in the base of control valve (9) until the wire contacts the check ball. The check ball should rise with light pressure on the wire. If the check ball is stuck, replace control valve (9). Apply clean engine oil to control valve (9) .
Install control valve (9), control valve springs (8), and control valve cover (6) in compression brake housing (5) .
Apply downward pressure to control valve cover (6) with a punch of suitable size. Install retaining ring (7) with Tooling (B). Slowly release the pressure from control valve cover (6) in order to ensure that retaining ring (7) is fully seated in the groove.Note: Repeat Steps 12 through 14 for the remaining control valve.
Illustration 14 g00523472
Illustration 15 g00523471
Improper assembly of parts that are spring loaded can cause bodily injury.To prevent possible injury, follow the established assembly procedure and wear protective equipment.
Inspect the condition of accumulator piston (4). The accumulator piston should be free of wear and score marks. Apply clean engine oil to accumulator piston (4) .
Install accumulator piston (4),

Caterpillar parts catalog:

Caterpillar parts catalog
TH514C, TH417C, TH407C, TH414C, TH406C, TH337C, TH336C, Telehandler Transmission DJB00001-00483 (MACHINE)
TH336C Telehandler MJR00271-UP (MACHINE)
TH406C Telehandler GAT00258-UP (MACHINE)
TH337C Telehandler DJB00484-UP (MACHINE)
TH407C Telehandler JJT00172-UP (MACHINE)
TH414C Telehandler KEK00373-UP (MACHINE)
TH417C Telehandler RRJ00246-UP (MACHINE)
TH514C Telehandler KKW00177-UP (MACHINE)


Parts pad Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.