AVSPARE.COM
parts catalog

PANEL INSTR 0876667 - Caterpillar



0876667 PANEL INSTR Caterpillar parts PANEL
Rating:
16
Alternative (cross code) number:
CA0876667
087-6667
0876667
Caterpillar 0876667 PANEL INSTR

Buy PANEL INSTR 0876667 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Table 1
Service Tools
Part Number Part
JERD2129 Cat ® Electronic Technician
478–0235 Communication Adapter Gp
257-9140 Digital Multimeter
146-4080(1) Digital Multimeter Gp
8T-3224 Needle Tip
7X-1710 Multimeter Probe
8T-8726 Adapter Cable As (3-Pin Breakout)
6V-3000 Connector Repair Kit
190-8900 Connector Repair Kit
175-3700 Connector Repair Kit
147-6456 Wedge Removal Tool
370-4617 Cable As
185-3996 Thread Lock Compound
1P-0810 Electrical Tape
1U-5804 Crimp Tool
327-8981 Cable As (Data Link Cable CA3)
305-5528 Harness As. (VIMS - 3G Service Cable)
5P-7277 Voltage Tester
425-6889 Cable As.
538-5051 Communication Adapter Gp
8T-0065 Silicone Sealant
8T-0500 Continuity Test Light
300-8648 Tester Group
459-0233 Wrench-Strap
5P-6029 Lockwire
314-8478 Diagonal Cutter
466-5339 Screed Temperature Sensor Socket
(1) This multimeter can use an RS232C cable to connect to a laptop computer or Dataview tool gp for troubleshooting.Note: Cat ® Electronic Technician (Cat ® ET) service tool is designed to run with Microsoft Windows.To use Cat ET, the following materials must be ordered:
Special Publication, JERD2124, "ET Single Use Program License"
Special Publication, JEHP1026, "Information and Requirements Sheet"
Special Publication, JERD2142, "Data Subscription"The Special Publication, JEHP1026, "Information and Requirements Sheet" lists the required hardware and the features of Cat ET. For instructions on servicing Sure Seal connectors, see Special Instruction, SMHS7531. For instructions on servicing the Deutsch DT type connectors, see Special Instruction, SEHS9615.Cat ET is not required to view or clear the diagnostic codes. However, the process of determining the diagnostic codes is easier with Cat ET. Cat ET may also display the history and parameter status of a diagnostic code.Cat ET is used to communicate to the electronic control module (ECM) over the data link by connecting to the machine diagnostic connector. For more information about connectors, see Troubleshooting, "Electrical Components and Connector Locations" and the machine Electrical Schematic.For instructions on servicing Sure Seal connectors, see Special Instruction, SMHS7531. For instructions on servicing Deutsch connectors, see Special Instruction, SEHS9615.Use a calibrated digital multimeter to test continuity and voltage. See the instructions that are provided in the multimeter manual to operate the multimeter safely. The 7X-1710 Multimeter Probes are used to take measurements at a connector without separating the connections. The probe cables are pushed into the back of the connector along the wire. The 8T-8726 Adapter Cable has a three-pin breakout and is used for sensor circuit measurements.Note: Use a 8T-0500 Continuity Tester and a 5P-7277 Voltage Tester to test a harness. Do not use a 8T-0500 Continuity Tester or a 5P-7277 Voltage Tester for electronic circuits.


Parts panel Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.