PANEL AS 1156320 - Caterpillar

Refer to Illustration 30 for dimensions for the placement of gusset (1). Gusset (1) will be welded to the platform frame near the left-hand firewall post (4). Weld gusset (1) to the platform using two slots (C).
Illustration 31 g06016326
(AA) 27.9 mm (1.1 inch)
(BB) 63.5 mm (2.5 inch)
(CC) 25.4 mm (1.0 inch)
(DD) 66.0 mm (2.6 inch)
(1) Gusset
Refer to Illustration 31 for the dimensions for the placement of gusset (1) on to the platform. Gusset (1) will be welded to the platform frame above the battery box to the left of the gusset that was previously installed. Weld gusset (1) using two slots (C).
Illustration 32 g06016400Bottom view of completed gusset installation.Exhaust Handrail Repair Procedure for 994F and 994H Wheel Loaders
Illustration 33 g06016577The procedure that follows will focus on the repair of the exhaust handrail.Handrail Gusset Fabrication
Fabricate the gussets shown in Illustrations 34 and 35.Gusset (1) and gusset (2) will be fabricated using 6.4 mm (0.25 inch) thick steel plate.
Illustration 34 g06017163
(1) Gusset
Table 3
Gusset (1) Dimensions
Dimension Measurement
(A) 109.2 mm (4.3 inch)
(B) 20.3 mm (0.8 inch)
(C) 45.7 mm (1.8 inch)
(D) 114.3 mm (4.5 inch)
(E) 25.4 mm (1 inch)
(F) 91.4 mm (3.6 inch)
(G) 248.9 mm (9.8 inch)
(H) 30.5 mm (1.2 inch)
(J) 693.4 mm (27.3 inch)
(K) 10.2 mm (0.4 inch)
(L) Radius 5.1 mm (0.2 inch)
(M) Radius 10.2 mm (0.4 inch)
(N) Radius 200.7 mm (7.9 inch)
(P) Radius 175.3 mm (6.9 inch)
Illustration 35 g06018602
(2) Gusset
Table 4
Gusset (2) Dimensions
Dimension Measurement
(A) 109.2 mm (4.3 inch)
(B) 20.3 mm (0.8 inch)
(C) 190.5 mm (7.5 inch)
(D) 261.6 mm (10.3 inch)
(E) 25.4 mm (1.0 inch)
(F) 91.4 mm (3.6 inch)
(G) 248.9 mm (9.8 inch)
(H) 30.5 mm (1.2 inch)
(J) 693.4 mm (27.3 inch)
(K) 10.2 mm (0.4 inch)
(L) Radius 5.1 mm (0.2 inch)
(M) Radius 10.2 mm (0.4 inch)
(N) Radius 10.2 mm (0.4 inch)
(P) Radius 200.7 mm (7.9 inch)
(R) Radius 175.3 mm (6.9 inch)
(S) 45.7 mm (1.8 inch) Handrail Gusset Installation Procedure
Illustration 36 g06019142
Clamp gusset (2) so that the edges of gusset (2) are aligned with the center line of tubes (3) and (4). Clamp gusset (1) so that edges of gusset (1) are aligned with the center line of tubes (3) and (5).
Illustration 37 g06019060
Weld the gussets where indicated in Illustration 37.