2433849 PANEL AS Caterpillar parts
C1.5, C2.2
Rating:
Alternative (cross code) number:
CA2433849
243-3849
2433849
CA2433849
243-3849
2433849
Weight: 2 pounds 0 kg.
GENERATOR SET,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Information:
Note: The removal procedure of the front wheel bearings and of the Duo-cone seal kit is identical for both sides of the machine. Only one side of the machine is shown.
Illustration 1 g00589508
Use Tooling (B) and a suitable lifting device to install the front suspension cylinder, the spindle, and the brake assembly on Tooling (F) .Note: The above photo shows the front suspension cylinder and the spindle assembly before the installation of the brake assembly. This photo is out of the sequence. This photo illustrates the use of Tooling (F) .
Illustration 2 g03292458
Remove plug (2), gasket (3), plug (4), gasket (5), bolts (6), and cover (7) from wheel assembly (1) .Note: If necessary, use two 1/2 inch - 13 forcing screws to remove cover (7) .
Drain the oil from the front wheel assembly into a suitable container for storage or for disposal. Refer to Operation and Maintenance Manual for the correct draining and filling procedures.
Illustration 3 g00478262
Remove O-ring seal (8) from cover (7) .
Illustration 4 g03292517
Remove bolts (9) and retainer (10). Note: If necessary, use two 1/2 inch - 13 forcing screws to remove the cover assembly.
Illustration 5 g03292537
Remove shims (11). Remove bearing cone (12) .
Illustration 6 g03292656
Use Tooling (B) and a suitable lifting device to remove wheel assembly (1). The weight of wheel assembly (1) is approximately 791 kg (1744 lb).
Illustration 7 g00476030
Illustration 8 g00477496
Use Tooling (D) in order to remove half of seal (14) from wheel assembly (1) .
Remove bearing cup (13) from the inside of front wheel assembly (1) .
Illustration 9 g00477495
Remove bearing cup (15) from the outside of front wheel assembly (1) .
Illustration 10 g00477492
Use two people to remove bearing cone (16). The weight of the bearing cone is approximately 27 kg (60 lb).
Illustration 11 g00477490
Use two M10-1.5 bolts, two bars, and two wood blocks to remove retainer assembly (17) from the brake hub.
Illustration 12 g00476045
Remove O-ring seal (18). Use Tooling (E) to remove the first half of seal (19) .
Illustration 13 g00477367
Remove O-ring seal (21) and O-ring seal (22) from the brake hub.
Use Tool (D) to remove the remaining half of seal (14) from the front service and parking brake.
Use Tool (E) to remove the remaining half of seal (19) from the retainer.
Illustration 1 g00589508
Use Tooling (B) and a suitable lifting device to install the front suspension cylinder, the spindle, and the brake assembly on Tooling (F) .Note: The above photo shows the front suspension cylinder and the spindle assembly before the installation of the brake assembly. This photo is out of the sequence. This photo illustrates the use of Tooling (F) .
Illustration 2 g03292458
Remove plug (2), gasket (3), plug (4), gasket (5), bolts (6), and cover (7) from wheel assembly (1) .Note: If necessary, use two 1/2 inch - 13 forcing screws to remove cover (7) .
Drain the oil from the front wheel assembly into a suitable container for storage or for disposal. Refer to Operation and Maintenance Manual for the correct draining and filling procedures.
Illustration 3 g00478262
Remove O-ring seal (8) from cover (7) .
Illustration 4 g03292517
Remove bolts (9) and retainer (10). Note: If necessary, use two 1/2 inch - 13 forcing screws to remove the cover assembly.
Illustration 5 g03292537
Remove shims (11). Remove bearing cone (12) .
Illustration 6 g03292656
Use Tooling (B) and a suitable lifting device to remove wheel assembly (1). The weight of wheel assembly (1) is approximately 791 kg (1744 lb).
Illustration 7 g00476030
Illustration 8 g00477496
Use Tooling (D) in order to remove half of seal (14) from wheel assembly (1) .
Remove bearing cup (13) from the inside of front wheel assembly (1) .
Illustration 9 g00477495
Remove bearing cup (15) from the outside of front wheel assembly (1) .
Illustration 10 g00477492
Use two people to remove bearing cone (16). The weight of the bearing cone is approximately 27 kg (60 lb).
Illustration 11 g00477490
Use two M10-1.5 bolts, two bars, and two wood blocks to remove retainer assembly (17) from the brake hub.
Illustration 12 g00476045
Remove O-ring seal (18). Use Tooling (E) to remove the first half of seal (19) .
Illustration 13 g00477367
Remove O-ring seal (21) and O-ring seal (22) from the brake hub.
Use Tool (D) to remove the remaining half of seal (14) from the front service and parking brake.
Use Tool (E) to remove the remaining half of seal (19) from the retainer.
Caterpillar parts catalog:
Parts panel Caterpillar catalog:
2627012
PANEL GP-ELECTRICAL
C1.5, C2.2
C1.5, C2.2
2995940
PANEL GP-ELECTRICAL
C2.2, C3.3, C4.4, C6.6
C2.2, C3.3, C4.4, C6.6
2619336
PANEL GP-ELECTRICAL
C1.5, C2.2
C1.5, C2.2
2627014
PANEL GP-ELECTRICAL
C1.5, C2.2
C1.5, C2.2
2666420
PANEL-LIGHT
C2.2, C3.3, C4.4, C6.6
C2.2, C3.3, C4.4, C6.6
2644160
PANEL AS
C2.2, C3.3, C4.4
C2.2, C3.3, C4.4
2921510
PANEL-BOX
C1.5, C4.4, C6.6
C1.5, C4.4, C6.6
2994528
PANEL-TOP
C2.2
C2.2
3186879
PANEL
C2.2
C2.2
2496421
PANEL-INSTRUMENT
C1.5, C2.2
C1.5, C2.2
2315913
PANEL GP-CONTROL
C1.5, C2.2
C1.5, C2.2
2433860
PANEL AS
C1.5, C2.2
C1.5, C2.2
2822321
PANEL
C2.2
C2.2
2454729
PANEL-END
C1.5, C2.2
C1.5, C2.2
2454730
PANEL AS
C1.5
C1.5
2454728
PANEL
C1.5
C1.5
2454727
PANEL
C1.5
C1.5
2454726
PANEL-TOP
C1.5
C1.5
2454725
PANEL
C1.5
C1.5
2454724
PANEL
C1.5
C1.5