2584042 PEDAL GP-GOVERNOR Caterpillar parts
272C, 297C, 299C
Rating:
Alternative (cross code) number:
CA2584042
258-4042
2584042
CA2584042
258-4042
2584042
COMPACT TRACK LOADER, SKID STEER LOADER,
Compatible equipment models: 2584042:
Number on catalog scheme:
5
For full view, you need register
Information:
Start By:a. remove steering clutches1. Drain the oil from the bevel gear compartment. 2. Remove lock (1) and nut (2) that holds the hub coupling to the shaft.3. Remove the cork seal from the hub coupling.
Do not loosen the hub coupling without nut (2) installed on the shaft.
4. Install nut (2) on the shaft again with approximately 3.18 mm (.125 in.) clearance between the nut and the hub coupling.5. Install tooling (A) and loosen hub coupling (3) from the shaft. Remove tooling (A), nut and hub coupling. The following steps are for installation of steering clutch hub coupling.
Make sure the splines are clean, dry and free of burrs before installation of the hub coupling.
6. Put hub coupling (3) in position on the shaft. Use tooling (B) and install hub coupling (3) on the shaft with a force of 133 to 178 kN (15 to 20 ton). The distance between the face of the hub coupling and the shoulder on the shaft must be 3.0 0.8 mm (.12 .03 in.).7. Install the cork seal on the hub coupling.8. Put 9S3263 Thread Lock on the threads and install nut (2). Tighten the nut to a torque of 475 47 N m (350 35 lb.ft.).9. Install lock (1).10. Fill the bevel gear case with correct oil to the correct level. See the Operation And Maintenance Manual.End By:a. install steering clutches
Do not loosen the hub coupling without nut (2) installed on the shaft.
4. Install nut (2) on the shaft again with approximately 3.18 mm (.125 in.) clearance between the nut and the hub coupling.5. Install tooling (A) and loosen hub coupling (3) from the shaft. Remove tooling (A), nut and hub coupling. The following steps are for installation of steering clutch hub coupling.
Make sure the splines are clean, dry and free of burrs before installation of the hub coupling.
6. Put hub coupling (3) in position on the shaft. Use tooling (B) and install hub coupling (3) on the shaft with a force of 133 to 178 kN (15 to 20 ton). The distance between the face of the hub coupling and the shoulder on the shaft must be 3.0 0.8 mm (.12 .03 in.).7. Install the cork seal on the hub coupling.8. Put 9S3263 Thread Lock on the threads and install nut (2). Tighten the nut to a torque of 475 47 N m (350 35 lb.ft.).9. Install lock (1).10. Fill the bevel gear case with correct oil to the correct level. See the Operation And Maintenance Manual.End By:a. install steering clutches
Caterpillar SIS machinery equipment:
Caterpillar parts catalog:
Parts pedal Caterpillar catalog:
3258383
PEDAL GP-GOVERNOR
246C, 256C, 262C, 262C2, 272C, 277C, 277C2, 279C, 279C2, 287C, 287C2, 289C, 289C2, 297C, 299C
246C, 256C, 262C, 262C2, 272C, 277C, 277C2, 279C, 279C2, 287C, 287C2, 289C, 289C2, 297C, 299C
246C, 256C, 262C, 262C2, 272C, 277C, 277C2, 279C, 279C2, 287C, 287C2, 289C, 289C2, 297C, 299C
3900899
PEDAL GP-BRAKE, XMSN & GOV
12M 3, 12M 3 AWD, 140M 3, 140M 3 AWD, 160M 3, 160M 3 AWD
12M 3, 12M 3 AWD, 140M 3, 140M 3 AWD, 160M 3, 160M 3 AWD
3526567
PEDAL GP-BRAKE
735B, 740B
735B, 740B
3423650
PEDAL AR-AUXILIARY
336D, 336D L, 336D LN
336D, 336D L, 336D LN
3443429
PEDAL AR-THIRD
568 FM LL
568 FM LL
1074627
PEDAL GP-GOVERNOR
910G, 914G, 924G, 924GZ, 928G, 930G, 938G, IT14G, IT28G, IT38G
910G, 914G, 924G, 924GZ, 928G, 930G, 938G, IT14G, IT28G, IT38G
1871755
PEDAL GP-BRAKE
844, 854G, 990 II, 992G
844, 854G, 990 II, 992G
2806342
PEDAL GP-GOVERNOR
246C, 256C, 262C, 277C, 279C, 287C, 289C
246C, 256C, 262C, 277C, 279C, 287C, 289C
3240669
PEDAL GP-GOVERNOR & BRAKE
D3K XL, D4K XL, D5K LGP
D3K XL, D4K XL, D5K LGP
3769610
PEDAL AR-THIRD
336E L, 336F L
336E L, 336F L
8U5706
PEDAL GP-BRAKE
206B, 212B
206B, 212B
2575698
PEDAL GP-GOVERNOR
938H, IT38H
938H, IT38H