AVSPARE.COM
parts catalog

PICKUP F/LINE 6V4950 - Caterpillar


6V4950 PICKUP F/LINE Caterpillar parts
Rating:
26
Alternative (cross code) number:
CA6V4950
6V-4950
6V4950
Caterpillar 6V4950 PICKUP F/LINE
Weight: 0.60 pounds 0 kg.

Buy PICKUP F/LINE 6V4950 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Illustration 1 g00803591
Schematic of the Solenoid Valve (Body Raise)
This diagnostic code is recorded when the ECM reads the current of the solenoid as being below normal.The possible causes are listed:
There is an open in the circuit.
The solenoid has failed.
The ECM has failed. This is unlikely.Note: The following procedure can create numerous related diagnostic codes. When all harnesses are reconnected, the related diagnostic codes will be shown as being not active. Clear all related diagnostic codes after this procedure is completed.Note: Ensure that CID 0724 FMI 05 for the solenoid is active. System Response:The hoist system will NOT raise the bed. The hoist system will be able to lower the bed.Test Step 1. CHECK THE SOLENOID.
Turn the disconnect switch and the key start switch to the ON position. DO NOT start the engine.
Disconnect the machine harness from the solenoid.
At the machine harness connector for the solenoid, place a jumper wire from contact 1 (wire G704-YL(Yellow)) to contact 2 (wire E790-PK(Pink)).
Observe the status of the diagnostic code. Expected Result:The diagnostic code is active. Then, the diagnostic code is NOT active as the jumper wire is installed and removed. Results:
YES - The circuit is correct. The solenoid has failed.Repair: Repeat this test "CHECK THE SOLENOID" in order to verify that the solenoid has failed. Replace the solenoid.STOP
NO - The diagnostic code remains active. Proceed to test step 2.Test Step 2. CHECK THE SOLENOID CIRCUIT FOR AN OPEN.
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the J2 machine harness connector from the ECM.
At the machine harness connector for the solenoid, the jumper wire remains installed.
At J2 machine harness connector, measure the resistance from contact J2-3 (wire E790-PK(Pink)) to J2-13 (wire G704-YL(Yellow)). Expected Result:The resistance should be less than 5 ohms.Results:
YES - The resistance is less than 5 ohms. The machine harness is correct. Proceed to test step 3.
NO - The resistance measurement is NOT correct. There is an open circuit in the machine harness.Repair: The open is in the wire for the solenoid signal or in wire (E790-PK(Pink)) of the machine harness. Repair the machine harness or replace the machine harness.STOPTest Step 3. CHECK IF THE DIAGNOSTIC CODE REMAINS.
Inspect the contacts and clean the contacts of the harness connectors.
Reconnect all harness connectors.
Turn the disconnect switch and the key start switch to the ON position.
Clear all inactive diagnostic codes.
Operate the machine.
Stop the machine and place the parking brake switch in the ON position.
Check if the diagnostic code for the solenoid is active. Expected Result:The diagnostic code is NO longer active. Results:
YES - The diagnostic code is NO longer active. The diagnostic code does not exist at this time. The initial diagnostic code was probably caused by a poor electrical connection or a short at one of the harness connectors that was disconnected and reconnected. Resume normal machine operation.STOP
NO - The diagnostic code has not been corrected.Repair: It is unlikely that the ECM has failed. Exit this procedure and perform this procedure again. Verify that the diagnostic code is active.


Parts pickup Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.