0787090 PILOT BEARIN Caterpillar parts
Rating:
Alternative (cross code) number:
CA0787090
078-7090
0787090
CA0787090
078-7090
0787090
Weight: 5 pounds 2 kg.
Information:
Illustration 7 g02735958
(3) Retainer Plate (5) Hairpin Clip (6) Lanyard
If necessary, remove hairpin clips (5) from retainer plates (3) and allow to hang from lanyards (6) .
Insert single chain link (8) into retainer plate (3), as shown. Attach hairpin clip (5) to retainer plate to lock chain sling (7) to lifting beam (10) .
Illustration 8 g02735961
(3) Retainer Plate (5) Hairpin Clip (7) Chain Sling (8) Chain Link (10) Lifting Beam Assembly
Count chain links (8) above or below the attached retainer plate (3) .
Illustration 9 g02735996
(3) Retainer Plate (5) Hairpin Clip (7) Chain Sling (8) Chain Link (10) Lifting Beam Assembly
Insert single chain link (8) into opposite retainer plate (3) at the same location on the second leg of chain sling (7). Attach hairpin clip (5) to retainer plate to lock chain sling to lifting beam (10) .
Make sure the number of chain links (8) above and below each retainer plate (3) are equal. Make sure that the angle between lifting beam assembly (10) and each leg of chain sling (7) is a minimum of 42°.
To avoid damage to the lifting beam assembly, chain sling, and related components, maintain a minimum 42° angle between each leg of the chain sling and lifting beam assembly.
Illustration 10 g02736001
(3) Retainer Plate (7) Chain Sling (8) Chain Link (10) Lifting Beam AssemblyNote: If necessary, move the lifting beam assembly up or down equally on both legs of chain sling (7) to achieve the correct angle.
Illustration 11 g02736005
(7) Chain Sling (9) Load Lever (10) Lifting Beam Assembly
If necessary, attach chain sling (7) (with lifting beam assembly (10) attached) to a suitable overhead lifting device.Note: Refer to the appropriate assembly and disassembly service manual for correct procedures for attaching and lifting the load.Note: Two chain slings (7) and lifting beam assemblies (10) can be attached to a suitable load lever (9) for four point lifting.Maintenance Section
Inspection
Inspect prior to each use for nicks, burrs, dents, cracks, bends, or worn parts. If damage is found, discontinue use until inspected and released for use by an approved inspector at the dealership.
Do not use unless load identification markings and warning films are legible.
Illustration 12 g02736017
Illustration 13 g02736019
Do not use if the outer tube (1) or inner tube (2) is bent or damaged, or if snap pin holes in tubes are worn.
Illustration 14 g02736023
Illustration 15 g02736027
Do not use if snap pin (4) is damaged or missing.
Do not use if hairpin clips (5) or lanyards (6) are damaged or missing.
Illustration 16 g02736036
Do not use if either of the retainer plates (3) are worn, bent, or damaged.
Have tool inspected annually by an approved dealership inspector.Cleaning/Lubrication
Clean the tooling using a nonsolvent based cleaner.
Lightly lubricate sliding parts as needed, for smooth operation.Storage
Store tooling indoors in a clean, dry location to prevent rust or corrosion.
Store the lifting beam assembly lying flat, or hanging from a suitable hook, to prevent falling.Tool Disposal
At the end of the operational life of the tool, destroy the tool and dispose of as scrap.
Parts pilot Caterpillar catalog:
0786566
PILOT PISTON
Caterpillar
Caterpillar
0786556
PILOT CAP AS
Caterpillar
Caterpillar
0786512
PILOT OPERAT
Caterpillar
Caterpillar
0786507
PILOT OPERAT
Caterpillar
Caterpillar
0786406
PILOT ACTUAT
Caterpillar
Caterpillar
0784599
"PILOT PRESS
Caterpillar
Caterpillar
0942883
PILOT POPPET
Caterpillar
Caterpillar
0940796
PILOT SEAT
Caterpillar
Caterpillar
0938349
PILOT HOSE
Caterpillar
Caterpillar
0927370
PILOT
Caterpillar
Caterpillar
0792764
PILOT LIGHT
Caterpillar
Caterpillar
0792222
PILOT LIGHT
Caterpillar
Caterpillar