PIN 0860523 - Caterpillar

Portions of this material are reprinted with permission from SAE J1939DA_201607© 2016 SAE International. SAE International is not responsible for any use or translation of this material, in whole or in part. Please contact SAE International to obtain a complete copy of SAE J1939DA_201607, the official definitive source of this standard.
Table 1
Flash Code Code Description of Code
00 52-11 Air Inlet Shutoff Shutdown
84-14 Quick Stop Occurrence
171-03 Ambient Air Temperature voltage high
171-04 Ambient Air Temperature voltage low
171-11 Ambient Air Temperature Data Lost
224-11 Theft Deterrent Active
224-14 Theft Deterrent Active with Engine Cranking
246-11 Brake Pedal Switch #1 Fault
247-11 Brake Pedal Switch #2 Fault
01 71-00 Idle Shutdown Override
12 111-02 Coolant Level signal invalid
111-03 Coolant Level voltage high
111-04 Coolant Level voltage low
13 174-03 Fuel Temperature voltage high
174-04 Fuel Temperature voltage low
14 121-05 Low/High Retarder current low
121-06 Low/High Retarder current high
122-05 Med/High Retarder current low
122-06 Med/High Retarder current high
21 41-03 8 Volt Supply voltage high
41-04 8 Volt Supply voltage low
232-03 5 Volt Supply voltage high
232-04 5 Volt Supply voltage low
24 100-03 Oil Pressure voltage high
100-04 Oil Pressure voltage low
25 102-00 Excessive Boost Pressure
102-03 Boost Pressure voltage high
102-04 Boost Pressure voltage low
26 108-03 Barometric Pressure voltage high
108-04 Barometric Pressure voltage low
27 110-03 Coolant Temperature voltage high
110-04 Coolant Temperature voltage low
28 91-13 Throttle Sensor Calibration
29 30-08 PTO Throttle signal invalid
30-13 PTO Throttle out of calibration
31 84-01 Vehicle Speed loss of signal
32 91-08 Throttle Position Invalid
34 64-12 Secondary Engine Speed loss of signal
190-12 Primary Engine Speed loss of signal
35 190-00 Engine Overspeed Warning
36 84-02 Vehicle Speed signal invalid
84-08 Vehicle Speed signal out of range
84-10 Vehicle Speed signal rate of change
38 105-03 Intake Manifold Air Temperature voltage high
105-04 Intake Manifold Air Temperature voltage low
41 84-00 Vehicle Overspeed Warning
42 22-11 Primary to Secondary Engine Speed Signal Calibration
22-13 Engine Speed Signal Calibration Not Performed
46 100-01 Low Oil Pressure Warning
100-11 Very Low Oil Pressure
47 71-01 Idle Shutdown
71-14 PTO Shutdown
51 168-02 ECM Battery Power Intermittent
55 N/A No Diagnostic Code Detected
56 253-02 Check Customer or System Parameters
253-11 Check Transmission Customer Parameters
58 231-11 J1939 Data Link Fault
249-11 J1922 Data Link Fault
59 252-11 Engine Software Incorrect
61 110-00 High Coolant Temperature Warning
110-11 Very High Coolant Temperature
62 111-01 Low Coolant Level Warning
111-11 Very Low Coolant Level
64 105-00 High Intake Manifold Air Temperature Warning
105-11 Very High Intake Manifold Air Temperature
65 174-00 High Fuel Temperature Warning
66 54-05 Auxiliary Output #06 current low
54-06 Auxiliary Output #06 current high
67 55-05 AuxiliaryOutput #07 current low
55-06 Auxiliary Output #07 current high
68 191-07 Transmission Not Responding
71 43-02 Key Switch Fault
72 1-11 Cylinder #1 Injector current fault
2-11 Cylinder #2 Injector current fault
73 3-11 Cylinder #3 Injector current fault
4-11 Cylinder #4 Injector current fault
74 5-11 Cylinder #5 Injector current fault
6-11 Cylinder #6 Injector current fault