1079734 PIN Caterpillar parts
315, 315B, 315B L, 315C, 315D L, 317, 317B LN
Rating:
Alternative (cross code) number:
CA1079734
107-9734
1079734
CA1079734
107-9734
1079734
Weight: 58 pounds 26 kg.
EXCAVATOR,
Number on catalog scheme:
3
For full view, you need register
Information:
Illustration 6 g01359198
Install prop rod (10).
Illustration 7 g01359201
Loosen three screws (11). Remove cover plate (12).
Illustration 8 g01359210
Remove retaining nut (13) on the coil of parking brake solenoid (14). Remove the coil of the parking brake solenoid from the valve stem. Note: The parking brake solenoid can be identified as having 374-PK(Pink) wire and 200-BK(Black) wire on the connector.
Illustration 9 g01359217
Open pump compartment (15) which is on the right side of the machine.
Assemble two sets of Tool (A) through Tool (E).
Illustration 10 g01359221
Connect one high pressure gauge (Tool (A)) to port "M1" (16).
Connect the second high pressure gauge (Tool (A)) to port "M2" (17).
Assemble Tool (F).
Assemble Tool (G).
Connect Tool (F) to Tool (G).
Illustration 11 g01359224
Remove the cap from charge pressure tap (18) on the left material feed pump. Connect Tool (G) to the charge pressure tap. Note: The switch for the screed lift must be reset to the HOLD position before the machine will start.
Move engine start switch (8) to the START position. Release the engine start switch when the engine starts.
Operate the engine at low idle for a few minutes.
Move throttle control switch (7) to the HIGH IDLE position. Hold the switch in this position for less than 1 second. The engine speed should increase to 2200 rpm.
Illustration 12 g01359228
Monitor the hydraulic oil temperature on the operator display. Operate the machine until the oil temperature reaches 43° 5.6°C (110° 9°F).
Record pressure at charge pressure tap (18).
Personal injury or death can result from sudden machine movement.Sudden movement of the machine can cause injury to persons on or near the machine.To prevent injury or death, make sure that the area around the machine is clear of personnel and obstructions before operating the machine.
Note: The travel mode switch must be in the TRAVEL position during this test. If the travel mode switch is in the PAVE position, the machine may drive through the parking brake.Note: If the machine moves at any time during this test, immediately move the propulsion lever back to the NEUTRAL position. Stop the machine and repair the parking brakes before this test is continued and/or before the machine is placed back into service.
Move parking brake switch
Caterpillar parts catalog:
Parts pin Caterpillar catalog:
1140, 1150, 120, 120B, 120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 129, 12E, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 140, 140B, 140G, 140H, 140H...
236B, 236B3, 242B3, 246C, 252B, 252B3, 256C, 257B3, 259B3, 262C, 262C2, 267B, 268B, 272C, 277C, 277C2, 279C, 279C2, 287C, 287C2, 289C, 289C2, 297C, 299C, 303.5C, 303C CR, 3044C, 304C CR, 305.5, 305.5D...
311C, 311D LRR, 312, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 314D CR, 314D LCR, 315, 316E L, 317, 320B, 320C, 325B L, 330B L, 613C, 613C II, 613G, 914G, 924F, 924G, 924GZ, ...
315, 315B, 315B L, 315C, 315D L, 316E L, 317, 317B LN, 318D L, 318D2 L, 318E L, 320 L, 320B, 320B L, 320C, 320C FM, 320C L, 320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC,...
315, 315B, 315B L, 315C, 317, 317B LN
115, 315, 315B, 315B L, 315C, 315D L, 316E L, 317, 317B LN, 318B, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D LN, 320B, 320C, 320C L, 320D, 320D GC, 320D L, 320D LRR, 320D RR, 320D2, 320D2 GC, 320...
312D, 312D L, 312D2 L, 315C, 317B LN, 318B, 318C, 320 L, 320B, 320C, 321D LCR, 322B L, 322B LN, 322C, 325B L, 325C, 330, 330 FM L, 950F, 950G, 953C, 963, 963C, M312, M315, M318, M320
315B L, 315C, 317B LN
311C, 313D2 LGP, 315C, 315D L, 316E L, 318B, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR,...
307, 312B L, 315, 315B L, 317, 317B LN, 318B, 320B, 320C, 322B L, 322B LN, 325B L, 330B L, 345B II, 345B L, 350, 350 L, 375, 5080
315, 315B, 315B FM L, 315B L, 317, 317B LN, 318B, 318C
315, 315B, 315B FM L, 315B L, 315C, 315D L, 316E L, 317, 317B LN, 318D L, 318D2 L, 318E L
6C8993
PIN
311B, 312, 312B L, 315, 315B L, 317, 317B LN, 318B, 320 L, 320B, 322 FM L, 322B L, 322B LN, 325 L, 325B L, 330, 330B L, 345B, 345B II, 345B II MH, 345B L, 350, 350 L, 375, 375 L, 385B, 5080, 5110B, M3...
311B, 312, 312B L, 315, 315B L, 317, 317B LN, 318B, 320 L, 320B, 322 FM L, 322B L, 322B LN, 325 L, 325B L, 330, 330B L, 345B, 345B II, 345B II MH, 345B L, 350, 350 L, 375, 375 L, 385B, 5080, 5110B, M3...
311C, 311D LRR, 312, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 314D CR, 314D LCR, 315, 316E L, 317, 320B, 320C, 325B L, 330B L, 613C, 613C II, 613G, 914G, 924F, 924G, 924GZ, ...
311B, 311C, 311D LRR, 311F LRR, 312, 312B, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313B, 313D, 313D2, 313D2 LGP, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 315C, 3...
315, 315B, 315C, 315D L, 316E L, 317, 318D L, 318D2 L, 318E L, G107B, M312, M313C, M313D, M315, M315C, M315D, M316C, M316D, PIN GRAB
315, 315B, 315B L, 315C, 315D L, 316E L, 317, 317B LN, 318D L, 318D2 L, 318E L
1219525
PIN AS
315, 315B L, 315C, 317, 317B LN
315, 315B L, 315C, 317, 317B LN
1237967
PIN AS
315, 315B L, 317, 317B LN
315, 315B L, 317, 317B LN
315, 315B, 315B L, 315C, 317, 317B LN
315, 315B, 315B L, 315C, 315D L, 316E L, 317, 317B LN, 318D L, 318D2 L, 318E L, 320 L, 320B, 320B L, 320C, 320C FM, 320C L, 320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC,...