1341808 PIN-G.E.T. Caterpillar parts
375 L, 385B, 390D, 994, 994D, 994F
Rating:
Alternative (cross code) number:
CA1341808
134-1808
1341808
CA1341808
134-1808
1341808
Weight: 3 pounds 1 kg.
Information:
END TO GROOVE
38
mm
GROOVE DIAMETER
34.2
mm
GROOVE WIDTH
14
mm
OD
35
mm
OVERALL LENGTH
240
mm
EXCAVATOR, WHEEL LOADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
CTP 1341808 Pin-Get for Ground Engagement Tools
CTP For Ground Engagement Tools || Sold in each || Easy in-and-out fit
CTP For Ground Engagement Tools || Sold in each || Easy in-and-out fit
CTP 1341808 Pin-Get for Ground Engagement Tools
CTP For Ground Engagement Tools || Sold in each || Easy in-and-out fit
CTP For Ground Engagement Tools || Sold in each || Easy in-and-out fit
Number on catalog scheme:
8
For full view, you need register
Compatible equipment models: 1341808:
Information:
Illustration 1 g00573861
Schematic For The Alarm. (1) Locomotive Engines - 410-WH: Marine Engines and Generator Set Engines - 025-GN.This diagnostic code is recorded when the Main Display Module reads the current in the circuit of the Action Alarm as above normal or the current is shorted to ground. As a result of this fault, the Action Alarm does not sound when the Action Alarm should sound.
Check the Alarm.
Disconnect the engine harness from the Action Alarm.Note: The Action Alarm has a problem if the FMI 06 diagnostic code is not active. The Action Alarm is not causing the problem if the FMI 06 diagnostic code is still active.
Measure the resistance across the terminals of the Action Alarm.Expected Result: The resistance across the terminals is 200 100 Ohms.Results:OK - The resistance is correct. If the Action Alarm does not sound, proceed to Step 2.Not OK - The resistance across the terminals is not correct. Replace the Action Alarm. STOP.
Check The Harness.
Turn the "ECS" switch to the OFF/RESET position.
Disconnect the engine harness from the Action Alarm.
Disconnect the engine harness from the Main Display Module.
At the engine harness connector for the Main Display Module, measure the resistance from the connector contact 4 to connector contact 2 (ground).Expected Result: The resistance should be greater than 5000 ohms.Results
OK - The resistance is correct. Proceed to Step 3.
Not OK - The resistance is less than 5000 ohms. The engine harness has a problem. Repair the engine harness or replace the engine harness. STOP.
Check The Main Display Module.
Turn the "ECS" switch to the OFF/RESET position.
Use the correct service tools to remove contact 4 from the engine harness connector for the Main Display Module.
Reconnect the engine harness connector to the Main Display Module.
Turn the "ECS" switch to the COOLDOWN/STOP position.Expected Result: FMI 06 should NOT be active.Results:
OK - FMI 06 is NOT active. The Main Display Module is NOT causing the problem. The problem is intermittent. The probable cause is a poor electrical connection at the harness connectors or a damaged harness. Check the harness for damage and clean the harness connectors as cleaning is required. STOP.
Not OK - FMI 06 is still active. The Main Display Module has a problem. Replace the Main Display Module. For more information, see Testing And Adjusting, "Module - Replace".
Caterpillar parts catalog:
Parts pin Caterpillar catalog:
322, 322 FM L, 322 LN, 322B L, 322B LN, 325, 325 L, 325 LN, 325B, 325B L, 330, 330 FM L, 330 L, 330B, 330B L, 345B II, 345B II MH, 345B L, 350, 375, 375 L, 5080, E240C, E300B, EL240B, M325B, TK1051, W...
365B, 365B II, 365C, 375, 375 L, 385C, 385C FS, 5080, 5090B
365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 374F L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 5090B
365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 374F L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 5090B
350, 350 L, 365B, 375, 375 L, 5080
365B, 365B II, 365B L, 375, 375 L, 5080
375, 375 L, 5080
375, 375 L, 5080
385B, 385C, 385C L, G107B, PIN GRAB
365B, 365B II, 365B L, 365C, 365C L, 374D L, 374F L, 385B, 385C, 385C L
365B, 365B II, 365B L, 365C, 365C L, 374D L, 385B, 385C, 385C L
365C, 385B, 385C, 385C L, 390D, 390D L, 390F L
1139688
PIN
5130, 994, 994D
5130, 994, 994D
365B, 365B II, 365C, 365C L, 365C L MH, 375, 385B, 385C, 385C FS, 385C L, 5080, 5090B, 5130, 980H, 980K, 994, 994D, 994F, 994H, D11R, D11T
1760801
PIN AS
994, 994D
994, 994D
1389320
PIN AS
994, 994D
994, 994D
814F, 814F II, 815F, 815F II, 816F, 816F II, 950B, 950B/950E, 950F, 950F II, 960F, 966D, 966F, 966F II, 970F
14G, 14H, 14H NA, 814, 814B, 814F, 814F II, 815, 815B, 815F, 815F II, 816F, 816F II, 966C, 966D, 966F, 966F II, 970F
6T5532
PIN
814F, 814F II, 815F, 815F II, 816F, 816F II, 966F, 966F II, 970F, R1600, R1600G, R1600H
814F, 814F II, 815F, 815F II, 816F, 816F II, 966F, 966F II, 970F, R1600, R1600G, R1600H
814, 815, 816, 950, 950B, 950F, 966C, 966D, 966F, 966R
1366783
PIN AS
5130, 994, 994D, 994F
5130, 994, 994D, 994F
5130, 5130B, 5230, 994, 994D