1651965 PIN AS Caterpillar parts
938G, 938G II
Rating:
Alternative (cross code) number:
CA1651965
165-1965
1651965
CA1651965
165-1965
1651965
WHEEL LOADER,
Number on catalog scheme:
1
For full view, you need register
Information:
Shipping Bracket Installation
Shipping brackets are used on hydraulic scrapers only when the scraper is being loaded or unloaded for shipping; or when it is being transported short distances with the draft arms removed.The shipping brackets are not interchangeable between scrapers or the left and right side of an individual scraper. To identify their location, the scraper serial number and the letter "L" for left or "R" for right is stamped on each shipping bracket.Do not exceed a speed of 5 MPH when the shipping brackets are attached and the draft arms are removed.The shipping brackets are of the types shown in the illustrations. The same instructions pertain to both types of brackets.
TYPICAL SHIPPING BRACKETS1. Raise the scraper bowl; place blocking beneath the scraper bowl floor, blocking the bowl approximately eleven inches (27.94 cm.) above the ground.2. From both draft arms (2), remove only those bolts (1) which interfere with the installation of the shipping bracket bolts (4).
PREPARING TO INSTALL SHIPPING BRACKET
1-Bolt. 2-Draft arm.3. Using a suitable hoist and sling arrangement, position shipping bracket (3); then insert bolts (4) securing the bracket to the spreader tube (5).
INSTALLING SHIPPING BRACKET
3-Shipping bracket. 4-Bolt. 5-Spreader tube.4. Install bolts (7) which hold the shipping bracket (3) to apron (8). Insert as many shims (6) as necessary to obtain a snug fit. Use the hydraulic scraper control system to raise or lower apron and/or bowl to obtain the proper bracket-to-apron alignment.
SHIPPING BRACKET INSTALLATION
3-Bracket. 6-Shims. 7-Bolt. 8-Apron.5. Tighten all bolts which secure the shipping brackets to both the spreader tube and apron.6. Attach a suitable hoist to the front of the draft arm (2); remove all bolts (1) which hold the draft arm to the spreader tube (5), and lower the front of the draft arm to the floor.
PREPARING TO REMOVE DRAFT ARM
1-Bolt. 2-Draft arm. 5-Spreader tube. 8-Retainer plate.7. Reposition the lifting chain. Remove retainer plate (8), and the bolts inside the bowl and remove the draft arm from pivot shaft (10) as shown.
REMOVING DRAFT ARM
10-Shaft.8. From inside the scraper bowl, remove shaft (10) with a 1H3107 Push Puller as shown.
REMOVING SHAFT
10-Shaft.Long Shipment By Rail
On long shipments by rail, with the scraper draft arms removed, the bowl lift cylinder rods and the apron lift link should be disconnected. The ejector should be blocked to the rear. To reduce possibility of damage to the disconnected cylinders and link, proceed as follows: Bowl Lift Cylinders:1. With the bowl lowered, remove both the bowl lift cylinder rod pins and shims and store for use when reassembling the scraper. The shims will be used to vertically realign the bowl lift cylinder rods with the brackets on the spreader beam.2. Retract the cylinder rods completely and securely fasten the cylinder rods in such a manner to prevent the rods from extending during shipment.3. Securely fasten the bowl lift cylinders to the spreader tube to prevent the cylinders from swinging. Apron Lift Link:Remove the pin and fasten the lift link to the spreader tube.
Shipping brackets are used on hydraulic scrapers only when the scraper is being loaded or unloaded for shipping; or when it is being transported short distances with the draft arms removed.The shipping brackets are not interchangeable between scrapers or the left and right side of an individual scraper. To identify their location, the scraper serial number and the letter "L" for left or "R" for right is stamped on each shipping bracket.Do not exceed a speed of 5 MPH when the shipping brackets are attached and the draft arms are removed.The shipping brackets are of the types shown in the illustrations. The same instructions pertain to both types of brackets.
TYPICAL SHIPPING BRACKETS1. Raise the scraper bowl; place blocking beneath the scraper bowl floor, blocking the bowl approximately eleven inches (27.94 cm.) above the ground.2. From both draft arms (2), remove only those bolts (1) which interfere with the installation of the shipping bracket bolts (4).
PREPARING TO INSTALL SHIPPING BRACKET
1-Bolt. 2-Draft arm.3. Using a suitable hoist and sling arrangement, position shipping bracket (3); then insert bolts (4) securing the bracket to the spreader tube (5).
INSTALLING SHIPPING BRACKET
3-Shipping bracket. 4-Bolt. 5-Spreader tube.4. Install bolts (7) which hold the shipping bracket (3) to apron (8). Insert as many shims (6) as necessary to obtain a snug fit. Use the hydraulic scraper control system to raise or lower apron and/or bowl to obtain the proper bracket-to-apron alignment.
SHIPPING BRACKET INSTALLATION
3-Bracket. 6-Shims. 7-Bolt. 8-Apron.5. Tighten all bolts which secure the shipping brackets to both the spreader tube and apron.6. Attach a suitable hoist to the front of the draft arm (2); remove all bolts (1) which hold the draft arm to the spreader tube (5), and lower the front of the draft arm to the floor.
PREPARING TO REMOVE DRAFT ARM
1-Bolt. 2-Draft arm. 5-Spreader tube. 8-Retainer plate.7. Reposition the lifting chain. Remove retainer plate (8), and the bolts inside the bowl and remove the draft arm from pivot shaft (10) as shown.
REMOVING DRAFT ARM
10-Shaft.8. From inside the scraper bowl, remove shaft (10) with a 1H3107 Push Puller as shown.
REMOVING SHAFT
10-Shaft.Long Shipment By Rail
On long shipments by rail, with the scraper draft arms removed, the bowl lift cylinder rods and the apron lift link should be disconnected. The ejector should be blocked to the rear. To reduce possibility of damage to the disconnected cylinders and link, proceed as follows: Bowl Lift Cylinders:1. With the bowl lowered, remove both the bowl lift cylinder rod pins and shims and store for use when reassembling the scraper. The shims will be used to vertically realign the bowl lift cylinder rods with the brackets on the spreader beam.2. Retract the cylinder rods completely and securely fasten the cylinder rods in such a manner to prevent the rods from extending during shipment.3. Securely fasten the bowl lift cylinders to the spreader tube to prevent the cylinders from swinging. Apron Lift Link:Remove the pin and fasten the lift link to the spreader tube.
Caterpillar parts catalog:
Parts pin Caterpillar catalog:
1090, 1190, 1190T, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 1290T, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 135H, 135H NA, 1390, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 1...
120, 120B, 120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 12E, 12G, 12H, 12H ES, 12H NA, 12K, 130G, 135H, 135H NA, 140, 140B, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14E, 14G, 14H, 14H NA, 153,...
10 FT, 10-20B, 10B, 117, 118, 119, 120, 120B, 120G, 127, 128, 129, 12E, 12F, 12G, 130G, 140, 140B, 140G, 141, 14E, 14G, 14H, 14H NA, 153, 16, 160G, 163, 1673, 16G, 16H, 16H NA, 16M, 172, 173B, 183, 18...
120G, 120H, 120H ES, 120H NA, 12F, 12G, 12H, 12H ES, 12H NA, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 143H, 14E, 14G, 14H, 14H NA, 16, 160G, 160H, 160H ES, 160H NA, 163H, 163H NA, 16G, 16H, ...
216, 216B, 216B3, 226B, 226B3, 232B, 236B, 236B3, 236D, 242B, 242B3, 242D, 246C, 246D, 247B, 247B3, 252B, 252B3, 256C, 257B, 257B3, 257D, 259B3, 259D, 262C, 262C2, 262D, 267B, 268B, 272C, 272D, 272D X...
120G, 12E, 12G, 130G, 140G, 14G, 16G, 191, 227, 229, 245, 245B, 30/30, 307B, 312B L, 312C, 315B L, 315C, 317B LN, 318B, 320B, 320C, 322B LN, 322C, 325B L, 325C, 330B L, 330C, 330C L, 3406, 345B II, 34...
30/30, 428, 5130, 65C, 75C, 75D, 85C, 85D, 918F, 924F, 928G, 928H, 928HZ, 938F, 938G, 938G II, 988F, 988F II, AP-1000, AP-1000B, AP-1055B, AP-650B, AP-800C, AP-800D, AP-900B, BG-225B, BG-225C, BG-2455...
10 FT, 10B, 117, 118, 119, 128, 129, 140, 16, 172, 184, 235, 245, 245B, 24M, 2670C, 30, 303E CR, 305.5E, 308E, 308E CR, 3160, 35, 414E, 416C, 416E, 420D, 420E, 420F, 422E, 426C, 428C, 428E, 428F, 430E...
16, 315D L, 316E L, 318D2 L, 318E L, 319D L, 319D LN, 320D, 320D GC, 320D L, 320D LRR, 320D RR, 320D2, 320E, 320E L, 320E LN, 320E LRR, 321D LCR, 323D L, 323D LN, 323D SA, 323E L, 324D, 324D L, 324E, ...
936, 936F, 938F, 938G, 938G II, 953, 953C, 962G, G936, IT38F, IT38G, IT62G, IT62G II
2470C, 2570C, 2670C, 2864C, 515, 518C, 525, 525B, 525C, 533, 535B, 535C, 543, 545, 545C, 553C, 563C, 573C, 586C, 918F, 924F, 928F, 928G, 928H, 928HZ, 930G, 936F, 938F, 938G, 938G II, 950F, 950F II, 95...
16, 525B, 525C, 535B, 535C, 545, 545C, 611, 613G, 615, 615C, 772, 814B, 814F, 814F II, 815B, 815F, 815F II, 816F, 816F II, 938F, 938G, 938G II, 938H, 950B, 950B/950E, 950F, 950F II, 950G, 950G II, 950...
1651963
PIN AS
938G, 938G II
938G, 938G II
1635203
PIN
938G, 950G, 966G II
938G, 950G, 966G II
1635202
PIN
938G, 938G II, 950G, 950G II, 966G II
938G, 938G II, 950G, 950G II, 966G II
1748663
PIN
938G, 938G II, 950G, 950G II, 950H, 962G, 962G II, 962H, 966G II, 966H, 972G II, 972H, 980G II, 980H, IT38G II, IT62G II, IT62H
938G, 938G II, 950G, 950G II, 950H, 962G, 962G II, 962H, 966G II, 966H, 972G II, 972H, 980G II, 980H, IT38G II, IT62G II, IT62H
1585784
PIN AS
938G, 950G, 962G
938G, 950G, 962G
1590958
PIN
938G, 950G, 962G
938G, 950G, 962G
6E0755
PIN-PIVOT
525B, 615C, 621F, 623E, 623F, 627F, 793, 793B, 814F, 814F II, 815F, 815F II, 816F, 816F II, 914G, 924F, 928F, 928G, 938F, 938G, 950B, 950F, 950F II, 950G, 950G II, 960F, 962G, 962G II, 966D, 966F, 966...
525B, 615C, 621F, 623E, 623F, 627F, 793, 793B, 814F, 814F II, 815F, 815F II, 816F, 816F II, 914G, 924F, 928F, 928G, 938F, 938G, 950B, 950F, 950F II, 950G, 950G II, 960F, 962G, 962G II, 966D, 966F, 966...
12H, 140H, 14H, 16H, 330C, 330C FM, 330C L, 330C MH, 621G, 623G, 627G, 631E, 631G, 637E, 637G, 725, 730, 735, 735B, 740, 740B, 844K, 938G, 950G, 990K, 993K, D10N, D10R, D10T, D250E II, D300E II, D350E...
1315166
PIN-HITCH
938G, 950G, 950G II, 962G, 966G, 966G II, 972G, 972G II
938G, 950G, 950G II, 962G, 966G, 966G II, 972G, 972G II
1696644
PIN AS
938G, 938G II
938G, 938G II
1651969
PIN AS
938G, 938G II
938G, 938G II
1651967
PIN AS
938G, 938G II
938G, 938G II