1R6225 PIN AS Caterpillar parts
311, 311D LRR, 312, 312B, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313B, 313D, 313D2, 313D2 LGP, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 324D L, 325D L, 325D MH,...
Rating:
Alternative (cross code) number:
CA1R6225
1R-6225
1R6225
CA1R6225
1R-6225
1R6225
Weight: 10 pounds 4 kg.
Information:
PIN LENGTH
181
mm
PIN OUTER DIAMERTER
59.86
mm
PIN PART NUMBER
5I3423
PLATE PART NUMBER
7Y2362
LUBE OUTLET
N
PIN END TYPE
CHAMFER
PIN TRANSV HOLE
N
PLATE FIXING HOLES
Y
EXCAVATOR, WHEELED EXCAVATOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$80.80
24 May 2022
US: Florida-Parts-Z
1R6225 - PIN AS. 990710 fit Caterpillar (CAT)
FIRST PRICE PARTS
FIRST PRICE PARTS
$44.92
15 Dec 2017
1012 Hundredths Pounds
CTP: CTP
Caterpillar PIN (1R6225) New Aftermarket By CTP
1R6225 Weight(lbs): 10.10 Length(cm): 21.0000 Width(cm): 18.4000 Depth(cm): 12.1000
1R6225 Weight(lbs): 10.10 Length(cm): 21.0000 Width(cm): 18.4000 Depth(cm): 12.1000
15 Dec 2017
1100 Hundredths Pounds
CTP: CTP
1R6225 Pin AS Fits Caterpillar 311D LRR 312 312B 312B L 312C 312C L 312D 312D L
Warranty
Warranty
Number on catalog scheme:
2
For full view, you need register
Compatible equipment models: 1R6225:
Information:
Installation Procedure
All Generator Sets Except 3500 Engine Family
Table 1
TOOLS NEEDED
Part Number Tool Quantity
8S-2328 Dial Indicator Group 1
Illustration 1 g00616707
(1) Flywheel Pilot Bore (2) Surface
Remove all dirt, burrs, and paint from the contact surfaces of the generator supports and the base. Remove the protection material (compound) from flywheel pilot bore (1) and from surface (2). There should be no protection material that makes contact with the coupling. All contact surfaces of the engine, the coupling, and the generator must be completely clean.
Illustration 2 g00295967
(3) Dial Indicator Group (4) Crankshaft Pulley
In order to manually rotate the engine, remove the timing pointer's cover from the engine's flywheel housing. Install dial indicator group (3). Refer to Illustration 2. The tip of the indicator must touch the face of crankshaft pulley (4). Use a bar between the flywheel and the flywheel housing in order to push the crankshaft toward the flywheel. This will remove all the end play. Put the dial indicator in the ZERO position. Move the crankshaft to the most forward position. Make a record of the total indicator reading (TIR). The TIR is the end play of the crankshaft.
Illustration 3 g00616727
(5) Shim Pack
Illustration 4 g00616734
(6) Plate Assembly (7) Bolts
Do not run the generator set unless the plate assembly has the correct clearance. If the plate assembly does not have the correct clearance, damage can occur to the engine and/or generator.
Before installation, temporarily position plate assembly (6) in the bore of the flywheel to check for clearance. There must be clearance between the plate assembly's outside diameter and the flywheel bore's inside diameter. The plate assembly (6) can be a single solid plate or the plate assembly can be numerous flexible plates.
Install a full shim pack (5) and plate assembly (6) on the generator with bolts (7). Tighten the bolts to the torques that are shown in Table 2.
Table 2
REQUIRED TORQUE
Engine Torque
D379, G379, D398, G398, D399, G399
505 45 N m (372.0 33.0 lb ft)
All other engines Standard torque Note: Incorrect torque of bolts (7) can distort the shims which may reduce rotor bearing end play. When the shims are assembled to the drive coupling, the bolts (7) must be tightened to the correct torque.Note: The total thickness of shims (5) must not cause a reduction of crankshaft end play. When the generator is installed, the total thickness of shims (5) must not cause bending of plate assembly (6) .
Illustration 5 g00295970
(8) Guide Bolt
Install guide bolt (8) in the flywheel.
Put the generator in position on the engine.
Illustration 6 g00295971
(9) Bolts (10) Bolts
Install bolts (9) and (10). Tighten bolts (9) and (10).
Illustration 7 g00295967
Install dial indicator group (3) in order to measure crankshaft end play at crankshaft pulley (4). In order to remove all end play, place a bar between the flywheel and the flywheel housing. Push the crankshaft toward the flywheel. Put the dial indicator in the ZERO position. Move the crankshaft to the most forward
All Generator Sets Except 3500 Engine Family
Table 1
TOOLS NEEDED
Part Number Tool Quantity
8S-2328 Dial Indicator Group 1
Illustration 1 g00616707
(1) Flywheel Pilot Bore (2) Surface
Remove all dirt, burrs, and paint from the contact surfaces of the generator supports and the base. Remove the protection material (compound) from flywheel pilot bore (1) and from surface (2). There should be no protection material that makes contact with the coupling. All contact surfaces of the engine, the coupling, and the generator must be completely clean.
Illustration 2 g00295967
(3) Dial Indicator Group (4) Crankshaft Pulley
In order to manually rotate the engine, remove the timing pointer's cover from the engine's flywheel housing. Install dial indicator group (3). Refer to Illustration 2. The tip of the indicator must touch the face of crankshaft pulley (4). Use a bar between the flywheel and the flywheel housing in order to push the crankshaft toward the flywheel. This will remove all the end play. Put the dial indicator in the ZERO position. Move the crankshaft to the most forward position. Make a record of the total indicator reading (TIR). The TIR is the end play of the crankshaft.
Illustration 3 g00616727
(5) Shim Pack
Illustration 4 g00616734
(6) Plate Assembly (7) Bolts
Do not run the generator set unless the plate assembly has the correct clearance. If the plate assembly does not have the correct clearance, damage can occur to the engine and/or generator.
Before installation, temporarily position plate assembly (6) in the bore of the flywheel to check for clearance. There must be clearance between the plate assembly's outside diameter and the flywheel bore's inside diameter. The plate assembly (6) can be a single solid plate or the plate assembly can be numerous flexible plates.
Install a full shim pack (5) and plate assembly (6) on the generator with bolts (7). Tighten the bolts to the torques that are shown in Table 2.
Table 2
REQUIRED TORQUE
Engine Torque
D379, G379, D398, G398, D399, G399
505 45 N m (372.0 33.0 lb ft)
All other engines Standard torque Note: Incorrect torque of bolts (7) can distort the shims which may reduce rotor bearing end play. When the shims are assembled to the drive coupling, the bolts (7) must be tightened to the correct torque.Note: The total thickness of shims (5) must not cause a reduction of crankshaft end play. When the generator is installed, the total thickness of shims (5) must not cause bending of plate assembly (6) .
Illustration 5 g00295970
(8) Guide Bolt
Install guide bolt (8) in the flywheel.
Put the generator in position on the engine.
Illustration 6 g00295971
(9) Bolts (10) Bolts
Install bolts (9) and (10). Tighten bolts (9) and (10).
Illustration 7 g00295967
Install dial indicator group (3) in order to measure crankshaft end play at crankshaft pulley (4). In order to remove all end play, place a bar between the flywheel and the flywheel housing. Push the crankshaft toward the flywheel. Put the dial indicator in the ZERO position. Move the crankshaft to the most forward
Cat SIS web machinery list:
Parts pin Caterpillar catalog:
324D, 329D LN, 330C L, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E L, 336E LN, 336F L, 340D L, 340D2 L, 345B II, 345B L, 345C, 345C L, 345D, 345D L, 345D L VG, 34...
324D, 330B L, 330C, 330C L, 330D, 330D L, 330D LN, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E L, 336E LN, 336F L, 340D L, 340D2 L, 345B II, 345B L, 345C, 345C L, 345D, 345D L, 345D L VG, 349D, ...
330, 330 FM L, 330B L, 345B, 345B II, 345B II MH, 345B L, 345C, 345C MH, 350, G107B, GSH15-60, PIN GRAB, W345B II, W345C MH
325C, 325C FM, 325C L, 325D, 325D FM, 325D L, 328D LCR, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN
325C, 325C FM, 325C L, 325D, 325D FM, 325D FM LL, 325D L, 325D MH, 328D LCR, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN, M325C MH, M325D L MH, M325D MH
330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L, M330D
325C, 330C, 330C L, 330D L, 330D MH
345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, W345C MH
345B, 345B II, 345B II MH, 345B L, 345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L VG, 349F L, 365B
345B, 345B II, 345B L, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, W345C MH
345B II, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, W345C MH
345B II, 345B L, 345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L VG, 349F L, 365B II, 385B
312, 315, 315B FM L, 317, 320 L, 320B, 320N, 322 FM L, 322B L, 322C, 325, 325 LN, 325B, 325B L, 325C, 330, 330B L, E240C
0859769
PIN
311, 311B, 311C, 311D LRR, 311F LRR, 312, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313B, 313D, 313D2, 313D2 LGP, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 315, 316...
311, 311B, 311C, 311D LRR, 311F LRR, 312, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313B, 313D, 313D2, 313D2 LGP, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 315, 316...
1184659
PIN
312
312
1158287
PIN
312
312
0937919
PIN
311, 311B, 312, 312B, 315, 315B, 315B FM L, 317, E110, E110B, E140, OEMS
311, 311B, 312, 312B, 315, 315B, 315B FM L, 317, E110, E110B, E140, OEMS
0997147
PIN
311, 311B, 312, 312B, 315, 315B, 315B FM L, 317, E110B, OEMS
311, 311B, 312, 312B, 315, 315B, 315B FM L, 317, E110B, OEMS
1R9082
PIN
311, 312
311, 312
1R9081
PIN
311, 312
311, 312
1R9080
PIN
311, 312
311, 312
1R9079
PIN
311, 312
311, 312
1332866
PIN AS
312, 312B L, 312C, 312D, 315, 315B L, 317, 317B LN
312, 312B L, 312C, 312D, 315, 315B L, 317, 317B LN
311, 311B, 311C, 311D LRR, 311F LRR, 312, 312B, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313B, 313D, 313D2, 313D2 LGP, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, E1...