2233596 PIN AS Caterpillar parts
305, 305.5, 306
Rating:
Alternative (cross code) number:
CA2233596
223-3596
2233596
CA2233596
223-3596
2233596
Weight: 4 pounds 2 kg.
Information:
PIN LENGTH
118
mm
PIN OUTER DIAMERTER
50
mm
PIN PART NUMBER
2234120
PLATE PART NUMBER
2233546
LUBE OUTLET
N
PIN END TYPE
CHAMFER
PIN TRANSV HOLE
N
PLATE FIXING HOLES
Y
MINI HYD EXCAVATOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$5.72
25 Apr 2021
0.11[0.05] Pounds
US: RF Engine
Fits John Deere 3.164, 3.179, 4.219 Rod Bushing Honable New R51728, RE63914, 223-3596
Pro Build
Pro Build
Number on catalog scheme:
9
For full view, you need register
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-1114 Vacuum Cap 1 Start By:
Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Machine Preparation for Disassembly and Assembly". Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.
Illustration 1 g00910597
Install Tooling (A) on the hydraulic tank. Attach hose (1A) to the nipple on Tooling (A) and to an air supply. Apply 276 to 414 kPa (40 to 60 psi) of air. This procedure will pull a vacuum on the hydraulic system.
Illustration 2 g01007360
Personal injury can result from the sudden release of high pressure oil.Be sure the engine has been shut off for a minimum of five minutes to ensure that the accumulator pressure is zero.The accumulator is filled with dry nitrogen. Do not loosen or remove the valve or the cap from the top of the accumulator.
Disconnect harness assembly (1).
Remove nut (2), washer (3), and coil assembly (4).
Illustration 3 g01007361
Remove cartridge assembly (5). Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A FT-1114 Vacuum Cap 1 Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
Illustration 4 g01007361
Install cartridge assembly (5). Tighten cartridge assembly (5) to a torque of 25 5 N m (18 4 lb ft).
Illustration 5 g01007360
Install coil assembly (4), washer (3), and nut (2). Tighten nut (2) to a torque of 9.5 1.5 N m (84.08 13.28 lb in).
Connect harness assembly (1).
Illustration 6 g00910597
Remove Tooling (A) from the hydraulic tank.
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-1114 Vacuum Cap 1 Start By:
Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Machine Preparation for Disassembly and Assembly". Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.
Illustration 1 g00910597
Install Tooling (A) on the hydraulic tank. Attach hose (1A) to the nipple on Tooling (A) and to an air supply. Apply 276 to 414 kPa (40 to 60 psi) of air. This procedure will pull a vacuum on the hydraulic system.
Illustration 2 g01007360
Personal injury can result from the sudden release of high pressure oil.Be sure the engine has been shut off for a minimum of five minutes to ensure that the accumulator pressure is zero.The accumulator is filled with dry nitrogen. Do not loosen or remove the valve or the cap from the top of the accumulator.
Disconnect harness assembly (1).
Remove nut (2), washer (3), and coil assembly (4).
Illustration 3 g01007361
Remove cartridge assembly (5). Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A FT-1114 Vacuum Cap 1 Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
Illustration 4 g01007361
Install cartridge assembly (5). Tighten cartridge assembly (5) to a torque of 25 5 N m (18 4 lb ft).
Illustration 5 g01007360
Install coil assembly (4), washer (3), and nut (2). Tighten nut (2) to a torque of 9.5 1.5 N m (84.08 13.28 lb in).
Connect harness assembly (1).
Illustration 6 g00910597
Remove Tooling (A) from the hydraulic tank.
Caterpillar parts catalog:
Parts pin Caterpillar catalog:
2233593
PIN AS
304, 305, 305.5
304, 305, 305.5
304, 305
2233577
PIN
304, 305
304, 305
2234723
PIN AS
305, 305.5
305, 305.5
2233588
PIN AS
304, 305
304, 305
305
2190709
PIN AS
304, 305, 305.5, 305.5E, 306, 306E
304, 305, 305.5, 305.5E, 306, 306E
2184681
PIN AS
303.5C, 303.5D, 303.5E, 303C CR, 303E CR, 304, 304C CR, 304D CR, 304E, 305, 305.5, 305.5D, 305.5E, 305C CR, 305D CR, 305E, 306, 306E
303.5C, 303.5D, 303.5E, 303C CR, 303E CR, 304, 304C CR, 304D CR, 304E, 305, 305.5, 305.5D, 305.5E, 305C CR, 305D CR, 305E, 306, 306E
2000898
PIN AS
305
305
2000896
PIN AS
305
305
2000899
PIN AS
305
305
2233594
PIN AS
305, 305.5
305, 305.5