2624830 PIN & SEAL GP-LINKAGE Caterpillar parts
992G
Rating:
Alternative (cross code) number:
CA2624830
262-4830
2624830
CA2624830
262-4830
2624830
WHEEL LOADER,
Compatible equipment models: 2624830:
Number on catalog scheme:
22
For full view, you need register
Information:
2Tire Inflation with Nitrogen (N)
Caterpillar recommends using dry nitrogen (N2) gas for both tire inflation, and tire pressure adjustments. Nitrogen is an inert gas and will not support combustion inside the tire.
Proper nitrogen inflation equipment, and training in using the equipment, are necessary to avoid over inflation. A tire blowout or rim failure can result from improper or misused equipment and serious personal injury or death can occur.Because a fully charged nitrogen cylinder's pressure is approximately 15 000 kPa (2200 psi), a tire blowout and/or rim failure can occur if the inflation equipment is not used correctly.
In addition to reducing the risk of an explosion, using nitrogen to inflate tires lessens the slow oxidation of the rubber and the accompanying gradual tire deterioration. This is especially important for tires that have an expected long service life (four or more years). It also reduces the corrosion of rim components and the resultant disassembly problems.
Use a self-attaching inflation chuck and stand behind the tread when inflating a tire, to prevent possible personal injury.
Set the tire inflation equipment regulator at no more than 140 kPa (20 psi) over the recommended tire pressure.
Use only Caterpillar Part 6V-4040 Nitrogen Tire Inflation Group, or equivalent, to inflate tires from a nitrogen gas cylinder. Refer to Special Instruction, SMHS7867, for tire inflation instructions.Use the same tire pressures for nitrogen inflation that are used for air inflation. Consult your tire dealer for operating pressures.Tire Shipping Pressure
The tire inflation pressures shown in the following chart are cold inflation shipping pressures. The operating inflation pressure is based on the weight of a ready-to-work machine without attachments, at rated payload, and in average operating conditions. Pressures for each application may vary and should always be obtained from your tire supplier.Tire Inflation Pressures Adjustment
A tire inflation in a warm shop area, 18 to 21°C (65 to 70°F), will be underinflated if the machine works in freezing temperatures. Low pressure shortens the life of a tire.When operating in freezing temperatures, consult the Operation and Maintenance Manual for Cold Weather Recommendations, SEBU5898, for adjusted inflation pressures.
Caterpillar recommends using dry nitrogen (N2) gas for both tire inflation, and tire pressure adjustments. Nitrogen is an inert gas and will not support combustion inside the tire.
Proper nitrogen inflation equipment, and training in using the equipment, are necessary to avoid over inflation. A tire blowout or rim failure can result from improper or misused equipment and serious personal injury or death can occur.Because a fully charged nitrogen cylinder's pressure is approximately 15 000 kPa (2200 psi), a tire blowout and/or rim failure can occur if the inflation equipment is not used correctly.
In addition to reducing the risk of an explosion, using nitrogen to inflate tires lessens the slow oxidation of the rubber and the accompanying gradual tire deterioration. This is especially important for tires that have an expected long service life (four or more years). It also reduces the corrosion of rim components and the resultant disassembly problems.
Use a self-attaching inflation chuck and stand behind the tread when inflating a tire, to prevent possible personal injury.
Set the tire inflation equipment regulator at no more than 140 kPa (20 psi) over the recommended tire pressure.
Use only Caterpillar Part 6V-4040 Nitrogen Tire Inflation Group, or equivalent, to inflate tires from a nitrogen gas cylinder. Refer to Special Instruction, SMHS7867, for tire inflation instructions.Use the same tire pressures for nitrogen inflation that are used for air inflation. Consult your tire dealer for operating pressures.Tire Shipping Pressure
The tire inflation pressures shown in the following chart are cold inflation shipping pressures. The operating inflation pressure is based on the weight of a ready-to-work machine without attachments, at rated payload, and in average operating conditions. Pressures for each application may vary and should always be obtained from your tire supplier.Tire Inflation Pressures Adjustment
A tire inflation in a warm shop area, 18 to 21°C (65 to 70°F), will be underinflated if the machine works in freezing temperatures. Low pressure shortens the life of a tire.When operating in freezing temperatures, consult the Operation and Maintenance Manual for Cold Weather Recommendations, SEBU5898, for adjusted inflation pressures.
Caterpillar SIS machinery equipment:
Caterpillar parts catalog:
Parts pin Caterpillar catalog:
773G, 773G OEM, 775G, 775G OEM, 776C, 776D, 777D, 777F, 777G, 784B, 784C, 785B, 785C, 785D, 854G, 854K, 992G, 992K, 993K, CX48-P2300, SPF343C, TH48-E70, TH48-E80
235C, 322B L, 322B LN, 322C, 323D L, 323D2 L, 324D, 325 L, 325B L, 325C, 325D, 326D L, 329D, 329D L, 330, 330B, 330B L, 330C, 330C L, 330D, 330D L, 336D, 336D2, 336E, 336E H, 340D L, 340D2 L, 345B II,...
235C, 245B, 245D, 324D, 328D LCR, 330, 330B L, 330C L, 336D, 336D2, 340D L, 340D2 L, 345B II, 345B L, 345C, 345C L, 345D, 345D L, 349D, 349D L, 349E, 349E L, 350, 365B, 365B II, 365B L, 365C, 365C L, ...
330B L, 330D L, 336D, 336E, 336E H, 345B, 345B II, 345B L, 350, 365B, 365C, 374D L, 375, 375 L, 5110B, 834G, 834H, 972H, 972K, 973D, 988F, 988F II, 988G, 988H, 990 II, 990H, 990K, 992C, 992D, 992G, 99...
611, 615, 615C, 621E, 621F, 621G, 623E, 623F, 623G, 627E, 627F, 627G, 631E, 633E II, 637E, 651E, 657E, 69D, 768C, 769C, 769D, 771C, 771D, 772B, 773B, 773D, 773E, 775B, 775D, 775E, 776C, 776D, 777B, 77...
345B II, 345C L, 350, 365B, 365B II, 365C, 365C L, 374D L, 375, 375 L, 385B, 385C, 385C L, 390D, 5080, 5110B, 5230, 980G, 988H, 988K, 990, 990 II, 990H, 992G
992G
345C L, 365B, 374D L, 374F L, 375, 375 L, 385B, 385C, 385C FS, 385C L, 390D, 5080, 5090B, 992C, 992G, 994, 994D, 994F
844, 844H, 844K, 854G, 854K, 990, 990 II, 990H, 990K, 992G, 992K
844, 844H, 844K, 854G, 854K, 990, 990 II, 990H, 990K, 992G, 992K
988F II, 988G, 990 II, 992G
992G
4239543
PIN GP-GRAPPLE
545D, 555D
545D, 555D
2121329
PIN GP-BULLDOZER
844, 844H, 844K
844, 844H, 844K
2318377
PIN GP
325C
325C
6J7548
PIN GROUP
7A, 8A, 8U
7A, 8A, 8U
3734372
PIN GP-GRAPPLE
525D, 535D
525D, 535D
3455399
PIN & LINK GP-LIFT ARM
262D, 287D, 289D
262D, 287D, 289D
3967672
PIN GP-HITCH
901C, 902C, 903C
901C, 902C, 903C
3G8931
PIN GP
517, D4H, D4H XL, D4HTSK II, D4HTSK III
517, D4H, D4H XL, D4HTSK II, D4HTSK III
2685606
PIN GP-COUPLER
324D, 324D L, 324E, 324E L, 324E LN, 329D, 329D L, 329E, 329E L, 330D L, 336D, 336D L, 336E, 336E L, 336F L, PIN GRAB
324D, 324D L, 324E, 324E L, 324E LN, 329D, 329D L, 329E, 329E L, 330D L, 336D, 336D L, 336E, 336E L, 336F L, PIN GRAB
1570225
PIN GP-HITCH
35, 45, 55
35, 45, 55
1778628
PIN GP
318C, 319D L, 319D LN, 320C, 320D, 320D GC, 320D L, 320D LRR, 320D RR, 320D2, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 321C, 321D LCR, 323D L, 323D LN, 323D SA, 323D2 L, 323E L
318C, 319D L, 319D LN, 320C, 320D, 320D GC, 320D L, 320D LRR, 320D RR, 320D2, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 321C, 321D LCR, 323D L, 323D LN, 323D SA, 323D2 L, 323E L