2T2138 PIN Caterpillar parts
615C, 623E
Rating:
Alternative (cross code) number:
CA2T2138
2T-2138
2T2138
CA2T2138
2T-2138
2T2138
Weight: 4 pounds 2 kg.
Information:
PIN LENGTH
132
mm
PIN OUTER DIAMERTER
43.97
mm
PIN PART NUMBER
2410099
PLATE PART NUMBER
2410100
LUBE OUTLET
N
MAX. THREAD SIZE
.50-13
PIN END TYPE
CHAMFER
PIN TRANSV HOLE
N
PLATE FIXING HOLES
N
WHEEL SCRAPER, WHEEL TRACTOR,
Information:
1. Remove the plug from location (1). Install tool (A) in the hole with the square end down. Move the governor control to the "ON" position until the rack stops against tool (A). The racks are now in center (zero) position. 2. Disconnect lines (2) from the fuel injection pumps. Put caps on all fuel openings.3. Use tool (B) to loosen the bushings. 4. Remove fuel injection pump with tool (C). Remove tool (C) and bushing (3) from the fuel injection pump. Remove the washer from bushing (3) and remove seal from under bushing.
When injection pumps, spacers and lifters are removed from the injection pump housing, keep the parts of each pump together so they can be installed back in their original location.
5. Disassemble the fuel injection pump. Remove ring (4). Make a separation of the bonnet from the plunger and barrel assembly (5).
Be careful when the injection pumps are disassembled. Do not cause damage to the surface on the plunger. The plunger and barrel for each pump are made as a set. Do not put the plunger of one pump in the barrel of another pump. If one part has wear install a complete new pump assembly. Be careful when the plunger is put into the bore of the barrel.
6. Remove the plunger assembly, washer and spring from the barrel.
Do not remove the gear segment from the plunger. If the gear is loose or has been removed from the plunger a new fuel injection pump must be installed.
7. Remove the ring, spring, collar and valve from the barrel. 8. Remove spacer (6) from the fuel injection pump housing.Install Fuel Injection Pumps
Make sure the fuel racks are in the center (zero) position before the fuel injection pumps are installed. 1. Put plunger (5), washer (6) and spring (4) in position on barrel (9). Put check valve assembly (3) and spring (8) in position in bonnet (7). Connect bonnet (7) and barrel (9) together with ring (2). Keep seal (1) with bonnet for use at installation.2. Put spacer (12) into position in the pump housing bore. Make sure the correct spacer is with each pump.3. Put the spacer in gear segment (10) in alignment with the groove in barrel (9). 4. Put the injection pump straight down into the housing bore so the space in gear segment (10) is in alignment with pin (11) and the groove in barrel (9) is in alignment with dowel (13). Use tool (C) to install the pump.5. Install seal (1) and bushing (14) in the pump housing bore. If the pump is in the correct position, bushing (14) will turn into the threads of the pump housing with the fingers until it is even with the housing. Tighten bushing (14) to a torque of 150 10 lb.ft. (205 14 N m) with tool (B). 6. Install the washer on bushing (14).7. Connect the fuel lines to the injection pumps, and tighten fuel line nuts to a torque of 30
When injection pumps, spacers and lifters are removed from the injection pump housing, keep the parts of each pump together so they can be installed back in their original location.
5. Disassemble the fuel injection pump. Remove ring (4). Make a separation of the bonnet from the plunger and barrel assembly (5).
Be careful when the injection pumps are disassembled. Do not cause damage to the surface on the plunger. The plunger and barrel for each pump are made as a set. Do not put the plunger of one pump in the barrel of another pump. If one part has wear install a complete new pump assembly. Be careful when the plunger is put into the bore of the barrel.
6. Remove the plunger assembly, washer and spring from the barrel.
Do not remove the gear segment from the plunger. If the gear is loose or has been removed from the plunger a new fuel injection pump must be installed.
7. Remove the ring, spring, collar and valve from the barrel. 8. Remove spacer (6) from the fuel injection pump housing.Install Fuel Injection Pumps
Make sure the fuel racks are in the center (zero) position before the fuel injection pumps are installed. 1. Put plunger (5), washer (6) and spring (4) in position on barrel (9). Put check valve assembly (3) and spring (8) in position in bonnet (7). Connect bonnet (7) and barrel (9) together with ring (2). Keep seal (1) with bonnet for use at installation.2. Put spacer (12) into position in the pump housing bore. Make sure the correct spacer is with each pump.3. Put the spacer in gear segment (10) in alignment with the groove in barrel (9). 4. Put the injection pump straight down into the housing bore so the space in gear segment (10) is in alignment with pin (11) and the groove in barrel (9) is in alignment with dowel (13). Use tool (C) to install the pump.5. Install seal (1) and bushing (14) in the pump housing bore. If the pump is in the correct position, bushing (14) will turn into the threads of the pump housing with the fingers until it is even with the housing. Tighten bushing (14) to a torque of 150 10 lb.ft. (205 14 N m) with tool (B). 6. Install the washer on bushing (14).7. Connect the fuel lines to the injection pumps, and tighten fuel line nuts to a torque of 30
Caterpillar parts catalog:
Parts pin Caterpillar catalog:
8J6583
PIN
615C, 623B, 623E
615C, 623B, 623E
8J6662
PIN
615, 615C, 623B, 623E
615, 615C, 623B, 623E
2T0222
PIN
615, 615C
615, 615C
2T0221
PIN
615, 615C
615, 615C
2T0220
PIN
615, 615C
615, 615C
8J7791
PIN
615C, 623B, 623E, 623F, 623G, 623H, 623K, 623K LRC
615C, 623B, 623E, 623F, 623G, 623H, 623K, 623K LRC
8J8081
PIN
623B, 623E
623B, 623E
6E1588
PIN
623E
623E
6E1595
PIN
623E
623E
9X6420
PIN-SPRING
350, 375, 375 L, 5080, 5130, 5130B, 5230, 623E, 994, 994D
350, 375, 375 L, 5080, 5130, 5130B, 5230, 623E, 994, 994D
6E1574
PIN
350, 375, 375 L, 5080, 5130, 5130B, 5230, 623E, 844, 854G, 990, 990 II, 992G, 994, 994D, CB-525B
350, 375, 375 L, 5080, 5130, 5130B, 5230, 623E, 844, 854G, 990, 990 II, 992G, 994, 994D, CB-525B
0455106
PIN-SPRING
615C, 623E, 623F, 623G, 623H, 633E
615C, 623E, 623F, 623G, 623H, 633E