3039455 PIN-TRACK Caterpillar parts
AP-1055D, AP-650B, AP-655D, BG-225C, BG-245C, BG655D, D3K XL, D3K2 LGP, D4G, D4K XL, D4K2 XL
Rating:
Alternative (cross code) number:
CA3039455
303-9455
3039455
CA3039455
303-9455
3039455
Weight: 1 pounds 0 kg.
ASPHALT PAVER, TRACK-TYPE TRACTOR,
Compatible equipment models: 3039455:
Number on catalog scheme:
For full view, you need register
Information:
START BY:a. remove oil pump 1. Check each connecting rod cap for its location on the crankshaft. Each cap must have a number (1) which is the same as the number on the connecting rod. Do not mix bearings.2. Turn the crankshaft until two of the pistons are at the bottom center.3. Remove connecting rod caps (2). Remove the lower bearing from the connecting rod caps.4. Push the connecting rods away from the crankshaft, and remove the upper bearings from the connecting rods.
Be careful not to damage the crankshaft journals. Do not turn the crankshaft while any of the connecting rod caps are removed.
Install the connecting rod bearings dry when the clearance checks are made. Put clean engine oil on the connecting rod bearing for final assembly.5. Install the upper bearing in connecting rods. Slowly pull the connecting rods on the crankshaft.6. Install the lower bearing in the connecting rod caps. Be sure tab (3) on the back of the bearings fits in the groove of the caps and connecting rods. Do not turn the crankshaft when Plastigage (A) is in position.7. Check the bearing clearance with tool (A) as follows:a. Put 2P2506 Thread Lubricant on the threads of the bolts and washers. Install the caps, tool (A) and the nuts finger tight. See the topic Install Crankshaft for service tips on the use of Plastigage (A).b. Tighten each nut to a torque of 80 8 N m (60 6 lb.ft.).c. Put a mark across the nuts and bolts. Tighten the nuts 120° more.8. Remove the caps and tool (A). Make sure the connecting rod bearing caps are installed with their identification number in alignment with the connecting rod number.9. Measure the width of the Plastigage to find the bearing clearance. The clearance for new bearings must be 0.071 to 0.168 mm (.0028 to .0066 in.). The maximum clearance for used bearings is 0.25 mm (0.010 in.).10. Install the caps. Tighten the nuts to a torque of 80 8 N m (60 6 lb.ft.). Tighten the nuts 120° more.11. Do Steps 1 through 10 for the other connecting rod bearings.END BY:a. install oil pump
Be careful not to damage the crankshaft journals. Do not turn the crankshaft while any of the connecting rod caps are removed.
Install the connecting rod bearings dry when the clearance checks are made. Put clean engine oil on the connecting rod bearing for final assembly.5. Install the upper bearing in connecting rods. Slowly pull the connecting rods on the crankshaft.6. Install the lower bearing in the connecting rod caps. Be sure tab (3) on the back of the bearings fits in the groove of the caps and connecting rods. Do not turn the crankshaft when Plastigage (A) is in position.7. Check the bearing clearance with tool (A) as follows:a. Put 2P2506 Thread Lubricant on the threads of the bolts and washers. Install the caps, tool (A) and the nuts finger tight. See the topic Install Crankshaft for service tips on the use of Plastigage (A).b. Tighten each nut to a torque of 80 8 N m (60 6 lb.ft.).c. Put a mark across the nuts and bolts. Tighten the nuts 120° more.8. Remove the caps and tool (A). Make sure the connecting rod bearing caps are installed with their identification number in alignment with the connecting rod number.9. Measure the width of the Plastigage to find the bearing clearance. The clearance for new bearings must be 0.071 to 0.168 mm (.0028 to .0066 in.). The maximum clearance for used bearings is 0.25 mm (0.010 in.).10. Install the caps. Tighten the nuts to a torque of 80 8 N m (60 6 lb.ft.). Tighten the nuts 120° more.11. Do Steps 1 through 10 for the other connecting rod bearings.END BY:a. install oil pump
Caterpillar parts catalog:
Parts pin Caterpillar catalog:
236B, 236B3, 242B3, 246C, 252B, 252B3, 256C, 257B3, 259B3, 262C, 262C2, 267B, 268B, 272C, 277C, 277C2, 279C, 279C2, 287C, 287C2, 289C, 289C2, 297C, 299C, 3044C, 315C, 317B LN, 318B, 906, 906H, 907H, 9...
12M, 140G, 140K, 140K 2, 140M, 160K, 325D, 325D FM, 325D FM LL, 325D L, 325D MH, 328D LCR, 329D, 329D L, 329D LN, 525C, 535C, 545C, 573, 584, 815B, 950H, 962H, AP-1055D, BG-2455D, BG-260D, C7, C9.3, I...
12M 3, 12M 3 AWD, 140M 3, 140M 3 AWD, 160M 3, 160M 3 AWD, 307, 307B, 307C, 307D, 308C, 308D, 308E, 308E CR, 308E SR, 311, 311B, 311C, 311D LRR, 311F LRR, 312, 312B, 312B L, 312C, 312C L, 312D, 312D L,...
311C, 311D LRR, 312, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 314D CR, 314D LCR, 315, 316E L, 317, 320B, 320C, 325B L, 330B L, 613C, 613C II, 613G, 914G, 924F, 924G, 924GZ, ...
16, 315D L, 316E L, 318D2 L, 318E L, 319D L, 319D LN, 320D, 320D GC, 320D L, 320D LRR, 320D RR, 320D2, 320E, 320E L, 320E LN, 320E LRR, 321D LCR, 323D L, 323D LN, 323D SA, 323E L, 324D, 324D L, 324E, ...
315C, 315D L, D3B, D3C, D3C II, D3C III, D3G, D3K XL, D3K2 LGP, D4C, D4C II, D4C III, D4G, D4K XL, D4K2 XL, D5C, D5C III, D5G, D5K LGP, D5K2 XL
315C, 315D L, 3P, 3S, D3B, D3C, D3C III, D3G, D3K XL, D3K2 LGP, D4B, D4C, D4C II, D4C III, D4G, D4K XL, D4K2 XL, D5C, D5C III, D5G, D5K LGP, D5K2 XL
120K, 120M, 120M 2, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 140B, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 143H, 160H, 160H ES, 160H NA,...
963, 963B, 963C, 963D, D3G, D3K XL, D3K2 LGP, D4G, D4K XL, D4K2 XL, D5G, D5K LGP, D5K2 XL
D3G, D4G, D5G
D3G, D4G, D5G
D3G, D4G, D5G
5G5069
PIN
910, D3G, D3K XL, D3K2 LGP, D4G, D4K XL, D4K2 XL, D5G, D5K LGP, D5K2 XL, IT12, IT12B, IT14B, IT14F
910, D3G, D3K XL, D3K2 LGP, D4G, D4K XL, D4K2 XL, D5G, D5K LGP, D5K2 XL, IT12, IT12B, IT14B, IT14F
2124757
PIN-DRAWBAR
D3G, D3K XL, D3K2 LGP, D4G, D4K XL, D4K2 XL, D5G, D5K LGP, D5K2 XL
D3G, D3K XL, D3K2 LGP, D4G, D4K XL, D4K2 XL, D5G, D5K LGP, D5K2 XL
1883538
PIN
D3G, D3K XL, D3K2 LGP, D4G, D4K XL, D4K2 XL, D5G, D5K LGP, D5K2 XL
D3G, D3K XL, D3K2 LGP, D4G, D4K XL, D4K2 XL, D5G, D5K LGP, D5K2 XL
D3G, D4G, D5G
D3G, D4G, D5G
D3G, D4G, D5G
1918283
PIN
572R II, D7R II, D7R XR, D8R, D8R II, D8T
572R II, D7R II, D7R XR, D8R, D8R II, D8T
2330873
PIN
D3G, D4G, D5G
D3G, D4G, D5G
2117801
PIN AS
561N
561N
2260314
PIN AS
561N
561N
2260313
PIN AS
561N
561N
2117795
PIN AS
561N, PL61
561N, PL61