3176600 PIN AS Caterpillar parts
323D L, 323D LN, 324D, 325D, 325D L
Rating:
Alternative (cross code) number:
CA3176600
317-6600
3176600
CA3176600
317-6600
3176600
Weight: 58 pounds 26 kg.
EXCAVATOR,
Number on catalog scheme:
32
For full view, you need register
Information:
Illustration 1 g02173656
Connections of the "Transmission Input Speed" SensorThis diagnostic code is associated with the "Transmission Input Speed" Sensor. The FMI 08 diagnostic code means that the ECM has determined that the signal frequency is not within the expected range.This sensor is a frequency sensor. The sensor sends a frequency to the ECM as the gear teeth pass the magnet. The voltage is proportional to the speed of the output shaft from the transmission. The frequency that is sent to the ECM increases when the speed of the teeth increases.The possible causes of this diagnostic code are listed below:
Intermittent connections or poor connections
The sensor is loose.
The sensor has failed.
The Chassis ECM has failed. A failure of the ECM is unlikely.Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear the diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 0669 FMI 08 is active before performing this procedure. The engine must be running in order for the diagnostic code to be active.Note: Use a digital multimeter for the measurements in this procedure. Test Step 1. INSPECT THE HARNESS CONNECTIONS.
Turn the disconnect switch and the key start switch to the OFF position.
Inspect all harness connections that are related to the sensor. Make sure that the connectors are clean and tight.
Check the connectors for proper mating. Ensure that all the seals are present and in place.
Check the harness for signs of damage or abrasion.
Check the wires at the connector. Ensure that the wires are secured tightly into the connector.
Perform a 45 N (10 lb) pull test on each of the wires that are associated with the circuit. Take care not to pull the wire out of the connector.
Check the exposed wires at the connectors for nicks or signs of abrasion.
Check for moisture inside the connector.
Check the connectors for dirty contacts or corroded contacts.
Check each pin and each socket of the machine harness connectors. Ensure that the contacts are properly installed. The contacts should mate correctly when the two pieces of the connector are placed together.Expected Result:The machine harness connectors are tight and free of corrosion.Results:
OK - The machine harness connectors are tight and free of corrosion. Proceed to Test Step 2.
NOT OK - The machine harness connectors are in need of repair.Repair: Repair the machine harness or replace the machine harness.STOPTest Step 2. CHECK THE CIRCUIT FOR AN OPEN.
Turn the disconnect switch and the key start switch to the OFF position.
Disconnect the machine harness from the sensor.
At the machine harness connector for the sensor, install a jumper wire between contact 1 and contact 2 of the harness.
Disconnect the machine harness connector J1 from the ECM.
At the J1 machine harness connectors for the ECM, measure the resistance from contact J1-4 for the sensor to J1-5.Expected Result:There should be less than 5.0 ohms resistance.Results:
YES - The machine harness is correct. Proceed to Test Step 3.
NO - There is an open circuit in the machine harness. The open
Caterpillar parts catalog:
Parts pin Caterpillar catalog:
320C, 325C, 325C L, 325D, 325D L, 329D LN, 330C
322C FM, 323E L, 324D FM, 324D FM LL, 325, 325 L, 325 LN, 325B L, 325C, 325C FM, 325D, 325D L, 325D MH, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN, OEMS
320D, 320D LRR, 323D L, 323D LN
320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E LN, 321D LCR, 323D L, 323D LN, 323D SA, 323D2 L, 323E L
320D, 320D FM, 320D L, 320D2, 320D2 L, 320E, 320E LN, 323D L, 323D LN, 323D SA, 323D2 L, 323E L, 325D, 325D FM, 325D L, 328D LCR, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN, 330D L
320D, 320D FM, 320D GC, 320D L, 320D LRR, 320D RR, 320D2, 320D2 L, 320E, 320E L, 320E LN, 323D L, 323D LN, 323D SA, 323D2 L, 323E L, 324D, 324D FM, 324D L, 324D LN, 324E, 324E L, 324E LN, 325D, 325D F...
320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321D LCR, 323D L, 323D LN, 323D SA, 323D2 L, 323E L, 324D, 324D L, 325D,...
320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321D LCR, 323D L, 323D LN, 323D SA, 323D2 L, 323E L, 324D, 324D L, 325D,...
115, 324D, 324D L, 324D LN, 324E, 324E L, 324E LN, 325B L, 325C, 325D, 325D L, 326D L, 328D LCR, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN, 330, 330 FM L, 330 L, 330B, 330B L, 330C, 330C L, 330D, 3...
320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 323D L, 323D LN, 323D SA, 323D2 L
325C, 325C FM, 325C L, 325D, 325D FM, 325D L, 328D LCR, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN
325C, 325C FM, 325C L, 325D, 325D FM, 325D FM LL, 325D L, 325D MH, 328D LCR, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN, M325C MH, M325D L MH, M325D MH
2905884
PIN AS
324D, 324D L, 325D L, 329E L, 330D L, 336D, 336D2, 336E L, 336E LH
324D, 324D L, 325D L, 329E L, 330D L, 336D, 336D2, 336E L, 336E LH
2905882
PIN AS
324D, 324D L, 325D L, 329E L, 330D L, 336D, 336D2, 336E L, 336E LH
324D, 324D L, 325D L, 329E L, 330D L, 336D, 336D2, 336E L, 336E LH
2905879
PIN AS
320D, 320D LRR, 324D, 324D L, 325D L, 329D
320D, 320D LRR, 324D, 324D L, 325D L, 329D
3187138
PIN
324D, 324D L, 324E, 324E L, 324E LN, 329D, 329D L, 329E, 329E L, 336D, 336D L, 336E, 336E L, PIN GRAB
324D, 324D L, 324E, 324E L, 324E LN, 329D, 329D L, 329E, 329E L, 336D, 336D L, 336E, 336E L, PIN GRAB
3187141
PIN-CYLINDER
324D, 324D L, 324E, 324E L, 324E LN, 329D, 329D L, 329E, 329E L, 336D, 336D L, 336E, 336E L, PIN GRAB
324D, 324D L, 324E, 324E L, 324E LN, 329D, 329D L, 329E, 329E L, 336D, 336D L, 336E, 336E L, PIN GRAB
3496117
PIN
324D, 324D L, 324E, 324E L, 324E LN, 329D, 329D L, 329E, 329E L, 336D, 336D L, 336E, 336E L, PIN GRAB
324D, 324D L, 324E, 324E L, 324E LN, 329D, 329D L, 329E, 329E L, 336D, 336D L, 336E, 336E L, PIN GRAB
2994929
PIN AS
324D L, 325B L, 325C, 325D L, 329D L
324D L, 325B L, 325C, 325D L, 329D L
2902267
PIN-TRACK
1090, 2290, 511
1090, 2290, 511
8E6094
PIN-TRACK MASTER
345B, 345C, 350, 350 L
345B, 345C, 350, 350 L
345B, 345B II, 345B II MH, 345B L, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 350, W345B II, W345C MH
3267295
PIN AS
324D, 324D LN, 325D, 325D L, 330D L, 330D LN, 330D MH
324D, 324D LN, 325D, 325D L, 330D L, 330D LN, 330D MH
3267298
PIN AS
324D, 324D LN, 325D, 325D L, 330D L, 330D LN, 330D MH
324D, 324D LN, 325D, 325D L, 330D L, 330D LN, 330D MH