3224583 PIN Caterpillar parts
428E, 432E, 442E
Rating:
Alternative (cross code) number:
CA3224583
322-4583
3224583
CA3224583
322-4583
3224583
Weight: 6 pounds 3 kg.
BACKHOE LOADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$37.16
08 Jun 2022
7.0[3.15] Pounds
US: ProperBuy
CTP Caterpillar Pin-y (3224583) Aftermarket
CTP
CTP
$36.48
24 Feb 2019
Unknown: Unknown
Caterpillar 3224583 PIN-Y New
Number on catalog scheme:
10
For full view, you need register
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5P-3525 Piston Ring Compressor 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Rotate the crankshaft until the bearing journals are at the bottom center. The bearing journals that are at the bottom center are for the piston installation.
Put clean engine oil on the crankshaft journals and on the inside of the cylinder liners. Put clean engine oil on the piston rings and the connecting rod bearings.
Move the piston rings on the pistons until the ring openings are separated by approximately 120 degrees.
Illustration 1 g00483337
Put the piston in the cylinder liner with the "V" mark on the piston in alignment with the "V" mark on the cylinder block. Put tool (A) in position on the cylinder block and compress the piston rings.
The "V" mark must be visible on the piston and the cylinder block. If the "V" mark is not visible, the piston must be installed with the relief for the valve positioned toward the pushrod opening in the cylinder block. Damage may result if the pistons are not installed properly.
Push the piston into the cylinder liner and out of the ring compressor.
Illustration 2 g00483701
Guide connecting rod (1) into position on the crankshaft.
Put clean engine oil (SAE 30) on the lower half of the connecting rod bearing and on the connecting rod bolts.
When the connecting rod caps are installed, ensure that the identification marks are aligned.
Install connecting rod cap (2) and the nuts that secure the connecting rod cap. Torque both of the nuts to 40 4 N m (30 3 lb ft). Mark the position of the nuts. Tighten each nut for an additional 90 degrees (1/4 turn).
Repeat Steps 1 through 8 for the remainder of the piston and connecting rods.End By:
Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install".
Install the engine oil pan plate. Refer to Disassembly and Assembly, "Engine Oil Pan Plate - Remove and Install".
Install the spacer plate. Refer to Disassembly and Assembly, "Spacer Plate - Remove and install".
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5P-3525 Piston Ring Compressor 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Rotate the crankshaft until the bearing journals are at the bottom center. The bearing journals that are at the bottom center are for the piston installation.
Put clean engine oil on the crankshaft journals and on the inside of the cylinder liners. Put clean engine oil on the piston rings and the connecting rod bearings.
Move the piston rings on the pistons until the ring openings are separated by approximately 120 degrees.
Illustration 1 g00483337
Put the piston in the cylinder liner with the "V" mark on the piston in alignment with the "V" mark on the cylinder block. Put tool (A) in position on the cylinder block and compress the piston rings.
The "V" mark must be visible on the piston and the cylinder block. If the "V" mark is not visible, the piston must be installed with the relief for the valve positioned toward the pushrod opening in the cylinder block. Damage may result if the pistons are not installed properly.
Push the piston into the cylinder liner and out of the ring compressor.
Illustration 2 g00483701
Guide connecting rod (1) into position on the crankshaft.
Put clean engine oil (SAE 30) on the lower half of the connecting rod bearing and on the connecting rod bolts.
When the connecting rod caps are installed, ensure that the identification marks are aligned.
Install connecting rod cap (2) and the nuts that secure the connecting rod cap. Torque both of the nuts to 40 4 N m (30 3 lb ft). Mark the position of the nuts. Tighten each nut for an additional 90 degrees (1/4 turn).
Repeat Steps 1 through 8 for the remainder of the piston and connecting rods.End By:
Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install".
Install the engine oil pan plate. Refer to Disassembly and Assembly, "Engine Oil Pan Plate - Remove and Install".
Install the spacer plate. Refer to Disassembly and Assembly, "Spacer Plate - Remove and install".
Caterpillar parts catalog:
Parts pin Caterpillar catalog:
246D, 24M, 262D, 272D, 277D, 279D, 287D, 289D, 299D, 305.5E, 345D, 345D L, 345D L VG, 349D, 349D L, 35, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 385B, 385C, 385C FS, 385C L, 385C L MH, ...
416B, 416C, 416D, 416E, 416F, 420D, 420E, 420F, 422E, 422F, 424B, 424B HD, 424D, 426C, 428B, 428C, 428D, 428E, 428F, 430D, 430E, 430F, 432D, 432E, 432F, 434E, 434F, 436C, 438C, 438D, 442D, 442E, 444E,...
416B, 416C, 416D, 420D, 422E, 422F, 424D, 428B, 428C, 428D, 428E, 428F, 432D, 432E, 432F, 434E, 434F, 438B, 438C, 438D, 442D, 442E, 444E, 444F
414E, 416B, 416C, 416D, 416E, 416F, 420D, 420E, 420F, 422E, 422F, 424D, 426B, 426C, 428B, 428C, 428D, 428E, 428F, 430D, 430E, 430F, 432D, 432E, 432F, 434E, 434F, 436C, 438C, 438D, 442D, 442E, 444E, 44...
14G, 16G, 302.2D, 302.4D, 302.5, 302.5C, 302.7D, 303.5, 303.5C, 303.5D, 303.5E, 303C CR, 303E CR, 304C CR, 304D CR, 304E, 305.5D, 305.5E, 305C CR, 305D CR, 305E, 414E, 416B, 416C, 416D, 416E, 416F, 42...
416C, 420D, 420E, 420F, 424D, 426C, 428C, 428D, 428E, 428F, 430D, 430E, 430F, 432D, 432E, 432F, 434E, 436C, 438C, 438D, 442D, 442E, 906H, 906H2, 907H, 907H2, 908H, 908H2
416C, 416D, 416E, 416F, 420D, 420E, 420F, 422E, 422F, 424D, 426C, 428C, 428D, 428E, 428F, 430D, 430E, 430F, 432D, 432E, 432F, 434E, 434F, 436C, 438C, 438D, 442D, 442E, 444E, 444F
307D, 308D, 308E2 CR, 416C, 416D, 416E, 416F, 420D, 420E, 420F, 422E, 422F, 424D, 426C, 428C, 428D, 428E, 428F, 430D, 430E, 430F, 432D, 432E, 432F, 434E, 434F, 436C, 438C, 438D, 442D, 442E, 444E, 444F
414E, 416D, 416E, 416F, 420D, 420E, 420F, 422E, 422F, 424D, 428D, 428E, 428F, 430D, 430E, 430F, 432D, 432E, 432F, 434E, 434F, 442D, 442E, 444E, 444F, 450E, 450F, TH220B, TH330B, TH340B, TH350B, TH355B...
120H, 12H, 135H, 140H, 143H, 14G, 14H, 14H NA, 160H, 163H, 16G, 16H, 16H NA, 414E, 416E, 416F, 420E, 420F, 422E, 422F, 428E, 428F, 430E, 430F, 432E, 432F, 434E, 434F, 442E, 444E, 444F, 450E, 450F, 515...
422E, 422F, 428E, 428F, 432E, 432F, 434E, 434F, 444F
422E, 422F, 428E, 428F, 432E, 432F, 434E, 434F, 442E, 444E, 444F
3678220
PIN
289C, 299C, 299D, 299D XHP
289C, 299C, 299D, 299D XHP
0950859
PIN-COTTER
259B3, 259D, 279C, 279C2, 279D, 289C, 289C2, 289D, 299C, 299D, 299D XHP, AP-600D, AP-655D, AP555E, AS4251C
259B3, 259D, 279C, 279C2, 279D, 289C, 289C2, 289D, 299C, 299D, 299D XHP, AP-600D, AP-655D, AP555E, AS4251C
420E, 735, 950 GC, 966H, 972H, C13 XQ350, C32, D3K XL, D4K XL, D5K LGP
3446334
PIN
422E, 422F, 428E, 428F, 434E, 434F
422E, 422F, 428E, 428F, 434E, 434F
3465063
PIN
428E, 428F, 432E, 432F, 434E, 434F, 442E, 444E, 444F
428E, 428F, 432E, 432F, 434E, 434F, 442E, 444E, 444F
2971330
PIN
428E, 428F, 432E, 432F, 434E, 434F, 442E, 444E, 444F
428E, 428F, 432E, 432F, 434E, 434F, 442E, 444E, 444F
428E, 432E, 442E
428E, 432E, 442E
428E, 432E, 442E
428E, 432E, 442E
428E, 432E, 442E
428E, 432E, 442E