3309669 PIN Caterpillar parts
422E, 422F, 428E, 428F, 432E, 432F, 434E, 434F, 442E, 444E, 444F
Rating:
Alternative (cross code) number:
CA3309669
330-9669
3309669
CA3309669
330-9669
3309669
Weight: 5 pounds 2 kg.
BACKHOE LOADER,
Compatible equipment models: 3309669:
Information:
Removal Procedure
Start By:
Remove the cab. Refer to Disassembly and Assembly, "Cab - Remove".
Remove the air cleaner. Refer to Disassembly and Assembly, "Air Cleaner - Remove and Install".Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.
Drain the hydraulic tank into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, "Refill Capacities".
Illustration 1 g01177952
Remove bolts (1) and guard assemblies (2) from both sides of the machine.
Illustration 2 g01177953
Disconnect hose assemblies (4) and clips (3) .
Illustration 3 g01177954
Disconnect clips (5), tube assemblies (6), harness assembly (7), and hose assemblies (8) .
Illustration 4 g01177955
Attach a suitable lifting device to hydraulic tank (8). The weight of hydraulic tank (8) is approximately 272 kg (600 lb).
Illustration 5 g01177956
Remove bolts (9) from both sides of the machine.
Remove the hydraulic tank.
Start By:
Remove the cab. Refer to Disassembly and Assembly, "Cab - Remove".
Remove the air cleaner. Refer to Disassembly and Assembly, "Air Cleaner - Remove and Install".Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.
Drain the hydraulic tank into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, "Refill Capacities".
Illustration 1 g01177952
Remove bolts (1) and guard assemblies (2) from both sides of the machine.
Illustration 2 g01177953
Disconnect hose assemblies (4) and clips (3) .
Illustration 3 g01177954
Disconnect clips (5), tube assemblies (6), harness assembly (7), and hose assemblies (8) .
Illustration 4 g01177955
Attach a suitable lifting device to hydraulic tank (8). The weight of hydraulic tank (8) is approximately 272 kg (600 lb).
Illustration 5 g01177956
Remove bolts (9) from both sides of the machine.
Remove the hydraulic tank.
Caterpillar parts catalog:
Parts pin Caterpillar catalog:
3166951
PIN AS
422E, 422F, 428E, 428F, 432E, 432F, 434E, 434F, 442E, 444E, 444F
422E, 422F, 428E, 428F, 432E, 432F, 434E, 434F, 442E, 444E, 444F
3166952
PIN AS
422E, 422F, 428E, 428F, 432E, 432F, 434E, 434F, 442E, 444E, 444F
422E, 422F, 428E, 428F, 432E, 432F, 434E, 434F, 442E, 444E, 444F
3260089
PIN AS
422E, 422F, 428E, 428F, 432E, 432F, 434E, 434F, 444F
422E, 422F, 428E, 428F, 432E, 432F, 434E, 434F, 444F
3863778
PIN AS
422E, 422F, 428E, 428F, 432E, 432F, 434E, 434F, 442E, 444E, 444F
422E, 422F, 428E, 428F, 432E, 432F, 434E, 434F, 442E, 444E, 444F
3209164
PIN
422E, 422F, 428E, 428F, 432E, 432F, 434E, 434F, 442E, 444E, 444F
422E, 422F, 428E, 428F, 432E, 432F, 434E, 434F, 442E, 444E, 444F
3209241
PIN
422E, 422F, 428E, 428F, 432E, 432F, 434E, 434F, 442E, 444E, 444F
422E, 422F, 428E, 428F, 432E, 432F, 434E, 434F, 442E, 444E, 444F
3285234
PIN
422E, 422F, 428E, 428F, 432E, 432F, 434E, 434F, 442E, 444E, 444F
422E, 422F, 428E, 428F, 432E, 432F, 434E, 434F, 442E, 444E, 444F
3224583
PIN
428E, 432E, 442E
428E, 432E, 442E
3224584
PIN
428E, 432E, 442E
428E, 432E, 442E
3224585
PIN
428E, 432E, 442E
428E, 432E, 442E
3224586
PIN
428E, 432E, 442E
428E, 432E, 442E
3224587
PIN
428E, 432E, 442E
428E, 432E, 442E
3512210
PIN
422E, 422F, 428E, 428F, 432E, 432F, 434E, 434F, 442E, 444E, 444F
422E, 422F, 428E, 428F, 432E, 432F, 434E, 434F, 442E, 444E, 444F
3291331
PIN
422E, 422F, 428E, 428F, 432E, 432F, 434E, 434F, 442E, 444E, 444F
422E, 422F, 428E, 428F, 432E, 432F, 434E, 434F, 442E, 444E, 444F
3330792
PIN
422E, 422F, 428E, 428F, 432E, 432F, 434E, 434F, 444F
422E, 422F, 428E, 428F, 432E, 432F, 434E, 434F, 444F
3330791
PIN
422E, 422F, 428E, 428F, 432E, 432F, 434E, 434F, 444F
422E, 422F, 428E, 428F, 432E, 432F, 434E, 434F, 444F
3330790
PIN
422E, 422F, 428E, 428F, 432E, 432F, 434E, 434F, 444F
422E, 422F, 428E, 428F, 432E, 432F, 434E, 434F, 444F
3285234
PIN
422E, 422F, 428E, 428F, 432E, 432F, 434E, 434F, 442E, 444E, 444F
422E, 422F, 428E, 428F, 432E, 432F, 434E, 434F, 442E, 444E, 444F
3166949
PIN
422E, 422F, 428E, 428F, 432E, 432F, 434E, 434F, 442E, 444E, 444F
422E, 422F, 428E, 428F, 432E, 432F, 434E, 434F, 442E, 444E, 444F
3166948
PIN
422E, 422F, 428E, 428F, 432E, 432F, 434E, 434F, 442E, 444E, 444F
422E, 422F, 428E, 428F, 432E, 432F, 434E, 434F, 442E, 444E, 444F
3289650
PIN
422E, 422F, 428E, 428F, 432E, 432F, 434E, 434F, 444F
422E, 422F, 428E, 428F, 432E, 432F, 434E, 434F, 444F
3166947
PIN
422E, 422F, 428E, 428F, 432E, 432F, 434E, 434F, 444F
422E, 422F, 428E, 428F, 432E, 432F, 434E, 434F, 444F
3166946
PIN AS
422E, 422F, 428E, 428F, 432E, 432F, 434E, 434F, 444F
422E, 422F, 428E, 428F, 432E, 432F, 434E, 434F, 444F
4251825
PIN AS
422E, 422F, 428E, 428F, 432E, 432F, 434E, 434F, 442E, 444E, 444F
422E, 422F, 428E, 428F, 432E, 432F, 434E, 434F, 442E, 444E, 444F