3595743 PIN AS Caterpillar parts
336E, 336E H, 336E L, 336E LH, 336E LN, 336F L
Rating:
Alternative (cross code) number:
CA3595743
359-5743
3595743
CA3595743
359-5743
3595743
Weight: 119 pounds 54 kg.
EXCAVATOR,
Compatible equipment models: 3595743:
Number on catalog scheme:
12
For full view, you need register
Information:
Specifications
Illustration 1 g02142711
Tightening sequence
Table 1
Specifications for 327-0652 Water Pump Gp
Callout Part Number Part Name Specification Description
- 101-3895
101-3771 Bolt Torque to...................
22 N m (16 lb ft)
Tighten the bolts in the sequence that is in illustration 1. Removal Procedure
Start By:
Remove the fan and the fan pulley. Refer to Disassembly and Assembly, "Fan" for the correct procedure.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Drain the coolant from the cooling system into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the correct procedure.
Loosen the hose clamps and remove the hose from the water pump inlet.
Illustration 2 g02164768
Remove bolts (4) .
Remove water pump (3) from front cover (1) .Note: If necessary, tap the water pump with a soft faced hammer in order to loosen the water pump.
Remove gasket (2) .Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A - Guide Stud
M8 by 90 mm 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Ensure that the water pump is clean and free from wear and damage. If necessary, replace the water pump. Clean the gasket surface of the water pump.
Illustration 3 g02164797
Illustration 4 g02164963
Clean the gasket surface of housing (1) .
Install Tooling (A) in Position (X) .
Use Tooling (A) in order to align new gasket (2) to housing (1). Install the gasket onto the housing.
Align water pump (3) to Tooling (A). Install the water pump to housing (1) .Note: Ensure that the gear of the water pump and the gear of the fuel injection pump mesh.
Install bolts (4). Refer to Illustration 3. Tighten the bolts finger tight.
Remove Tooling (A) and install remaining bolts (4) .
Illustration 5 g01985813
Tighten the bolts in the sequence that is shown in Illustration 5 to a torque of 22 N m (195 lb in).
Install the hose to the water pump inlet. Tighten the hose clamps securely.
Fill the cooling system with coolant. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the correct procedure.End By: Install the fan and the fan pulley. Refer to Disassembly and Assembly, "Fan" for the correct procedure.
Illustration 1 g02142711
Tightening sequence
Table 1
Specifications for 327-0652 Water Pump Gp
Callout Part Number Part Name Specification Description
- 101-3895
101-3771 Bolt Torque to...................
22 N m (16 lb ft)
Tighten the bolts in the sequence that is in illustration 1. Removal Procedure
Start By:
Remove the fan and the fan pulley. Refer to Disassembly and Assembly, "Fan" for the correct procedure.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Drain the coolant from the cooling system into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the correct procedure.
Loosen the hose clamps and remove the hose from the water pump inlet.
Illustration 2 g02164768
Remove bolts (4) .
Remove water pump (3) from front cover (1) .Note: If necessary, tap the water pump with a soft faced hammer in order to loosen the water pump.
Remove gasket (2) .Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A - Guide Stud
M8 by 90 mm 2
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Ensure that the water pump is clean and free from wear and damage. If necessary, replace the water pump. Clean the gasket surface of the water pump.
Illustration 3 g02164797
Illustration 4 g02164963
Clean the gasket surface of housing (1) .
Install Tooling (A) in Position (X) .
Use Tooling (A) in order to align new gasket (2) to housing (1). Install the gasket onto the housing.
Align water pump (3) to Tooling (A). Install the water pump to housing (1) .Note: Ensure that the gear of the water pump and the gear of the fuel injection pump mesh.
Install bolts (4). Refer to Illustration 3. Tighten the bolts finger tight.
Remove Tooling (A) and install remaining bolts (4) .
Illustration 5 g01985813
Tighten the bolts in the sequence that is shown in Illustration 5 to a torque of 22 N m (195 lb in).
Install the hose to the water pump inlet. Tighten the hose clamps securely.
Fill the cooling system with coolant. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the correct procedure.End By: Install the fan and the fan pulley. Refer to Disassembly and Assembly, "Fan" for the correct procedure.
Cat SIS web machinery list:
Parts pin Caterpillar catalog:
324D, 324D L, 324D LN, 324E, 324E L, 324E LN, 325D, 325D L, 326D L, 328D LCR, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2...
324D, 324D L, 324D LN, 324E, 324E L, 324E LN, 325D, 325D L, 326D L, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, ...
324D, 324D L, 324D LN, 324E, 324E L, 324E LN, 325D, 325D L, 326D L, 328D LCR, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN, 330C L, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D...
325C, 328D LCR, 330, 330 FM L, 330 L, 330B, 330B L, 330C, 330C FM, 330C L, 330D, 330D FM, 330D L, 330D LN, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E H, 336E L, 336E LH, 336E LN, 336F L, 340D L...
1290T, 1390, 2491, 2590, 325C, 328D LCR, 330, 330 FM L, 330 L, 330B, 330B L, 330C, 330C FM, 330C L, 330C MH, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E H, 336E H...
1290T, 1390, 2491, 2590, 330, 330 FM L, 330 L, 330C FM, 330C L, 330D, 330D L, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F L, 340D L, 340D2 L,...
320D, 320D FM, 320D GC, 320D L, 320D LRR, 320D RR, 320D2, 320D2 L, 320E, 320E L, 320E LN, 323D L, 323D LN, 323D SA, 323D2 L, 323E L, 324D, 324D FM, 324D L, 324D LN, 324E, 324E L, 324E LN, 325D, 325D F...
115, 324D, 324D L, 324D LN, 324E, 324E L, 324E LN, 325B L, 325C, 325D, 325D L, 326D L, 328D LCR, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN, 330, 330 FM L, 330 L, 330B, 330B L, 330C, 330C L, 330D, 3...
324D, 329D LN, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E L, 336E LN, 336F L, 340D L, 340D2 L, 345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L,...
324D, 329D LN, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E L, 336E LN, 336F L, 340D L, 340D2 L, 345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L,...
324D, 329D LN, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E L, 336E LN, 336F L, 340D L, 340D2 L, 345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L,...
324D, 329D LN, 330C L, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E L, 336E LN, 336F L, 340D L, 340D2 L, 345B II, 345B L, 345C, 345C L, 345D, 345D L, 345D L VG, 34...
3744568
PIN
328D LCR
328D LCR
3744567
PIN-LINK
328D LCR
328D LCR
4410043
PIN AS
374D L
374D L
4410044
PIN AS
374D L, 374F L
374D L, 374F L
2646344
PIN
374D L
374D L
3671444
PIN AS
374D L, 374F L
374D L, 374F L
3715557
PIN AS
336E L, 336E LH, 336F L
336E L, 336E LH, 336F L
3715554
PIN
336E L, 336E LH, 336F L
336E L, 336E LH, 336F L
3715555
PIN AS
336E L, 336E LH, 336F L
336E L, 336E LH, 336F L
3715553
PIN
336E L, 336E LH, 336F L
336E L, 336E LH, 336F L
3715545
PIN AS
336E L, 336E LH, 336F L
336E L, 336E LH, 336F L
3362698
PIN AS
336E, 336E L, 336E LN, 336F L
336E, 336E L, 336E LN, 336F L