AVSPARE.COM
parts catalog

PIN AS-YM 3967285 - Caterpillar



3967285 PIN AS-YM Caterpillar parts PIN
Rating:
44
Alternative (cross code) number:
CA3967285
396-7285
3967285
Caterpillar 3967285 PIN AS-YM
Weight: 10 pounds 4 kg.

Buy PIN AS-YM 3967285 Caterpillar genuine, new aftermarket tractor parts with delivery

Related part:
1014020  PIN AS-YM  3967285  CL
  For full view, you need register

Information:

Connection Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8S-7610 Base 2
396-9840 Hydraulic Cylinder 2
9U-6600 Hand Hydraulic Pump 2
B 283-1495 Stand Assembly 2
8S-7611 Tube 2
8S-7615 Pin 2
Put the track in position under the track roller frame.
Use Tooling (A) to remove the machine from Tooling (B) .
Remove Tooling (B). Use Tooling (A) and lower the machine on the track.
Illustration 1 g00733401
Fasten a chain to track (7) and to a lift truck. Use the lift truck and pull track (7) over the front idler.
Pull track (7) until the track bushings engage with the sprocket segments on the final drive.
Start the machine and turn the final drive in a reverse direction. This will pull the track together.
Remove the chain from the track.
Illustration 2 g00733836
Align the lower end (9) of the master link with the upper end (8) of the master link. The serrations of both ends of the master link must be engaged.
Illustration 3 g00733838
Apply 2P-2506 Thread Lubricant to the threads, the body, and the washer face of bolts (6).
Put master shoe (4) in position on the master link. Install four bolts (6) that hold the master link together. Tighten the bolts to a torque of 400 70 N m (295 52 lb ft). Tighten the bolts 120 5 degrees more.
Illustration 4 g00733399
Tighten relief valve (2) and fill valve (3). Tighten the valves to a torque of 35 7 N m (26.0 5.0 lb ft).
Illustration 5 g00733840
Adjust the track with the following procedure.Note: The track adjustment procedure should be performed under the same conditions of the machine operations. Packing must NOT be removed from the track if packing conditions exist on the job.
Move the machine forward. Allow the machine to come to a stop without the use of the brakes.
Put a tight line between the grouser tips at the sprocket and the front idler.
Measure distance (X) from the line to the lowest point of sag of the grouser tips. Put 5P-0960 Multipurpose Type Grease in the track adjuster, and adjust the track until distance (X) is 100 10 mm (4.0 0.4 inch). This is the sag (curve) in the track between the sprocket and the front idler.
Do not tighten the track more if distance (Y) is 105 mm (4.1 inch) or more. The track must be removed and reconditioned.
Illustration 6 g00733842
Put the O-ring seal and cover (1) in position on the rear track roller frame. Install the bolts.


Parts pin Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.