3H1156 PIN Caterpillar parts
120G, 12G, 130G, 140G, 14G, 14H, 14H NA, 160G, 16G, 16H, 16H NA, 621E, 621F, 631E, 637E, 641B, 651E, 657B, 657E, 657G, 666B, 735, 740, 769C, 772B, 773B, 776, 777, 777B, 784B, 784C, 785, 785B, 785C, 78...
Rating:
Alternative (cross code) number:
CA3H1156
3H-1156
3H1156
CA3H1156
3H-1156
3H1156
Weight: 0.01 pounds 0 kg.
Information:
OVERALL LENGTH
28.58
mm
OUTSIDE PIN DIAMETER
3.175
mm
END TYPE A
CHAMFER
END TYPE B
CHAMFER
FLAT/VENTED
N
INSIDE DIAMETER
0
ARTICULATED TRUCK, WHEEL TRACTOR,
Number on catalog scheme:
12
For full view, you need register
Information:
Installation Procedure
1. Loosen bolts (1) that hold the governor drive housing in position against the adapter. See Illustration 1.
Illustration 1.2. Install support (2) on the governor. Do no tighten the bolts. See Illustration 2. A new support is now used that has slots (notches) in it. These supports can be installed between the governor and cover in Step 9.
Illustration 2.3. Put clean engine oil or glycerine on the bore of the lip type seal in the cover.4. Make sure two bolts (4) are in position in cover (5) and install the cover on output terminal shaft (7). Install two bolts (3) but do not tighten them at this time.5. Install lever (6) on the output terminal shaft as shown. Install the bolt and washer that holds the lever in position.6. Put the governor and cover in position on the engine. Make sure the side of the governor that is nearest to the engine block is parallel to the accessory drive housing. Install and tighten bolts (10). See Illustration 3.
Illustration 3.7. Move the governor and drive housing as needed until the bolt holes in the cover are in alignment with the bolt holes in the accessory drive housing. Tighten bolts (9).8. Tighten bolts (8) that hold the cover in position against the accessory drive housing.9. Tighten bolts (3) and the bolts that hold support (2) in position against the governor.10. Make sure output terminal shaft (7) turns freely. See Illustration 4. If the output terminal shaft does not move freely, do Steps 6 through 10 again. Spring pressure in the Woodward 3161 Governor should cause the output terminal shaft to go back to the fuel-off position when released from the full-fuel position. Spring pressure in the Woodward UG8 Governor should cause the output terminal shaft to move when released from the full-fuel position but it will not go all the way to the fuel-off position.
Illustration 4.
1. Loosen bolts (1) that hold the governor drive housing in position against the adapter. See Illustration 1.
Illustration 1.2. Install support (2) on the governor. Do no tighten the bolts. See Illustration 2. A new support is now used that has slots (notches) in it. These supports can be installed between the governor and cover in Step 9.
Illustration 2.3. Put clean engine oil or glycerine on the bore of the lip type seal in the cover.4. Make sure two bolts (4) are in position in cover (5) and install the cover on output terminal shaft (7). Install two bolts (3) but do not tighten them at this time.5. Install lever (6) on the output terminal shaft as shown. Install the bolt and washer that holds the lever in position.6. Put the governor and cover in position on the engine. Make sure the side of the governor that is nearest to the engine block is parallel to the accessory drive housing. Install and tighten bolts (10). See Illustration 3.
Illustration 3.7. Move the governor and drive housing as needed until the bolt holes in the cover are in alignment with the bolt holes in the accessory drive housing. Tighten bolts (9).8. Tighten bolts (8) that hold the cover in position against the accessory drive housing.9. Tighten bolts (3) and the bolts that hold support (2) in position against the governor.10. Make sure output terminal shaft (7) turns freely. See Illustration 4. If the output terminal shaft does not move freely, do Steps 6 through 10 again. Spring pressure in the Woodward 3161 Governor should cause the output terminal shaft to go back to the fuel-off position when released from the full-fuel position. Spring pressure in the Woodward UG8 Governor should cause the output terminal shaft to move when released from the full-fuel position but it will not go all the way to the fuel-off position.
Illustration 4.
Cat SIS web machinery list:
Parts pin Caterpillar catalog:
14G, 16G
12G, 130G, 140G
12G, 130G
12G, 130G
12G, 130G
14G, 16G
14G
14G
14G
130G
130G
130G
1183756
PIN
315B, 933, 933C, D3C III, D4C III, D5C III
315B, 933, 933C, D3C III, D4C III, D5C III
1184740
PIN
315B, 933, 933C, D3C III, D4C III, D5C III
315B, 933, 933C, D3C III, D4C III, D5C III
4252722
PIN AS
305.5E
305.5E
3074472
PIN
308E2 CR, A26B
308E2 CR, A26B
301.7D CR
301.7D CR
12F, 140, 141, 14E, 153, 163, 235, 245, 518, 518C, 621, 641, 650B, 651, 657B, 666, 816, 920, 930, 941, 943, 950, 951B, 953, 953C, 966C, 980B, 992, 992C, 992D, D4D, D5, D5B, D5E, D6C, D6D, D6E, D6E SR,...
215, 225, 323D LN, 941, D4D, D4E, PM-201, PM-565, PM-565B, PR-1000
14E, 215, 215B, 225, 225D, 227, 229, 229D, 231D, 515, 525, 525B, 525C, 535B, 535C, 545, 545C, 910, D7G, D8K
5D4824
PIN
120, 120B, 140, 140B, 215, 225, 235, 245, 768B, 769, 772, 773
120, 120B, 140, 140B, 215, 225, 235, 245, 768B, 769, 772, 773
1P8679
PIN
941, 955H, D44B, D550B, D6H, D8K
941, 955H, D44B, D550B, D6H, D8K