4D7780 PIN Caterpillar parts
16
Rating:
Alternative (cross code) number:
CA4D7780
4D-7780
4D7780
CA4D7780
4D-7780
4D7780
Weight: 5 pounds 2 kg.
MOTOR GRADER,
Compatible equipment models: 4D7780:
Number on catalog scheme:
None
For full view, you need register
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A(1) 9U-6198 Crankshaft Turning Tool 1
A(2) 9U-7336 Housing 1
5P-7305 Engine Turning Tool 1
B 8T-3052 Degree Wheel 1
(1) The Crankshaft Turning Tool is used on the front pulley.
(2) This Tool is used in the aperture for the electric starting motor.Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Discard all used Connecting Rod fasteners.
Inspect the pins of the crankshaft for damage. If the crankshaft is damaged, replace the crankshaft. Refer to Disassembly and Assembly, "Crankshaft - Remove" and Disassembly and Assembly, "Crankshaft - Install" for the correct procedure. Ensure that the bearing shells are clean and free from wear and damage. If necessary, replace the bearing shells.
Illustration 1 g02437999
Install upper bearing shell (5) into connecting rod (3). Ensure that the locating tab for the upper bearing shell is correctly seated in the slot in the connecting rod. Note: The ends of the upper bearing shell must be centered in the connecting rod. The ends of the upper bearing shell must be equally positioned in relation to the mating faces of the connecting rod.
Lubricate upper bearing shell (5) with clean engine oil.
Use Tooling (A) to rotate the crankshaft until the crankshaft pin is at the bottom dead center position.
Carefully pull connecting rod (3) against the crankshaft pin. Note: Do not allow the connecting rod to contact the piston cooling jet.
Clean connecting rod cap (2). Install lower bearing shell (4) into connecting rod cap (2). Ensure that the locating tab for the lower bearing shell is correctly seated in the slot in the connecting rod cap.
Lubricate the pin of the crankshaft and lubricate lower bearing shell (4) with clean engine oil.
Illustration 2 g02437998
Install connecting rod cap (2) to connecting rod (3). Note: Ensure that etched Number (X) on connecting rod cap (2) matches etched Number (X) on connecting rod (3). Ensure the correct orientation of the connecting rod cap. The locating tab for the upper bearing shell and the lower bearing shell should be on the same side.Note: Do not reuse the old connecting rod bolts in order to secure the connecting rod cap.
Install new bolts (1) to the connecting rod. Tighten the bolts evenly to a torque of 40 N m (30 lb ft).
Turn the bolts through an additional 120 degrees in a clockwise direction. Use Tooling (B) to achieve the correct final torque.
Ensure that the installed connecting rod assembly has tactile side play. Rotate the crankshaft in order to ensure that there is no binding.
Repeat Step 2 through Step 11 for the remaining connecting rod bearings. Note: If all connecting rod bearings require replacement, the procedure can be carried out on two cylinders at the same time. The procedure can be carried out on the following pairs of cylinders. 1 with 4 and 2 with 3. Ensure that both pairs of the connecting rod bearings are installed before changing from one
Table 1
Required Tools
Tool Part Number Part Description Qty
A(1) 9U-6198 Crankshaft Turning Tool 1
A(2) 9U-7336 Housing 1
5P-7305 Engine Turning Tool 1
B 8T-3052 Degree Wheel 1
(1) The Crankshaft Turning Tool is used on the front pulley.
(2) This Tool is used in the aperture for the electric starting motor.Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Discard all used Connecting Rod fasteners.
Inspect the pins of the crankshaft for damage. If the crankshaft is damaged, replace the crankshaft. Refer to Disassembly and Assembly, "Crankshaft - Remove" and Disassembly and Assembly, "Crankshaft - Install" for the correct procedure. Ensure that the bearing shells are clean and free from wear and damage. If necessary, replace the bearing shells.
Illustration 1 g02437999
Install upper bearing shell (5) into connecting rod (3). Ensure that the locating tab for the upper bearing shell is correctly seated in the slot in the connecting rod. Note: The ends of the upper bearing shell must be centered in the connecting rod. The ends of the upper bearing shell must be equally positioned in relation to the mating faces of the connecting rod.
Lubricate upper bearing shell (5) with clean engine oil.
Use Tooling (A) to rotate the crankshaft until the crankshaft pin is at the bottom dead center position.
Carefully pull connecting rod (3) against the crankshaft pin. Note: Do not allow the connecting rod to contact the piston cooling jet.
Clean connecting rod cap (2). Install lower bearing shell (4) into connecting rod cap (2). Ensure that the locating tab for the lower bearing shell is correctly seated in the slot in the connecting rod cap.
Lubricate the pin of the crankshaft and lubricate lower bearing shell (4) with clean engine oil.
Illustration 2 g02437998
Install connecting rod cap (2) to connecting rod (3). Note: Ensure that etched Number (X) on connecting rod cap (2) matches etched Number (X) on connecting rod (3). Ensure the correct orientation of the connecting rod cap. The locating tab for the upper bearing shell and the lower bearing shell should be on the same side.Note: Do not reuse the old connecting rod bolts in order to secure the connecting rod cap.
Install new bolts (1) to the connecting rod. Tighten the bolts evenly to a torque of 40 N m (30 lb ft).
Turn the bolts through an additional 120 degrees in a clockwise direction. Use Tooling (B) to achieve the correct final torque.
Ensure that the installed connecting rod assembly has tactile side play. Rotate the crankshaft in order to ensure that there is no binding.
Repeat Step 2 through Step 11 for the remaining connecting rod bearings. Note: If all connecting rod bearings require replacement, the procedure can be carried out on two cylinders at the same time. The procedure can be carried out on the following pairs of cylinders. 1 with 4 and 2 with 3. Ensure that both pairs of the connecting rod bearings are installed before changing from one
Caterpillar parts catalog:
Parts pin Caterpillar catalog:
12E, 12F, 14E, 16, 211B, 214B, 307B, 3114, 3116, 3126, 3208, 322, 325, 325 L, 325B L, 325C, 325D MH, 3304, 3304B, 3306, 3306B, 330B L, 330C MH, 330D MH, 3406, 3406B, 3406C, 3406E, 3408, 3408B, 3408C, ...
120G, 120H, 120H ES, 120H NA, 12M 2, 12M 3, 12M 3 AWD, 135H, 135H NA, 140M 2, 140M 3, 140M 3 AWD, 16, 160M 2, 160M 3, 160M 3 AWD, 16G, 245, 2864C, 3114, 3116, 3126, 3208, 320B, 322B L, 322B LN, 322C, ...
120H, 120H ES, 120H NA, 120M, 12F, 12H, 12H ES, 12H NA, 12M, 135H NA, 140H, 140H ES, 140H NA, 140M, 143H, 14H, 14H NA, 14M, 16, 160H, 160H ES, 160H NA, 160M, 163, 163H, 163H NA, 1693, 16H, 16H NA, 16M...
16, 1673C, 1693, 16G, 215, 229D, 245, 245B, 3208, 3304, 3306, 3306B, 3406, 3406B, 3408, 3408B, 3408C, 3408E, 3412, 3412C, 3412E, 3508, 3508C, 3512, 3512B, 3516, 3516B, 5130, 5230, 527, 589, 594, 615, ...
120, 120B, 120G, 120H, 120H ES, 120H NA, 12E, 12G, 12H, 12H ES, 12H NA, 130G, 135H, 135H NA, 140, 140B, 140G, 140H, 140H ES, 140H NA, 143H, 14E, 14G, 14H NA, 16, 160G, 160H, 160H ES, 160H NA, 163H NA,...
1140, 1150, 120, 120B, 120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 129, 12E, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 140, 140B, 140G, 140H, 140H...
117, 118, 119, 120, 120B, 120G, 120M, 127, 129, 12E, 12F, 130G, 140, 140B, 141, 14E, 14G, 14H, 14H NA, 14M, 16, 163, 16G, 16H, 16H NA, 16M, 172, 183, 184, 191, 215, 227, 235, 235C, 24, 245, 245B, 25, ...
12E, 14E, 16, 24H, 24M, 30/30, 3176, 3176B, 3406E, 3408, 3408B, 3408C, 3408E, 3412, 3412C, 3412D, 3412E, 3456, 3606, 3608, 3612, 3616, 508, 517, 518, 518C, 527, 528, 528B, 530B, 54, 561M, 561N, 572R, ...
12E, 141, 14E, 16, 183, 191, 3208, 3306, 3406, 3406B, 3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 508, 517, 561B, 561C, 578, 583R, 589, 594, 613C, 613C II, 613G, 615, 631C, 641, 641B, ...
120B, 12E, 140, 140B, 14E, 16, 229, 235, 235C, 245, 375 L, 528, 561C, 571G, 572G, 572R, 572R II, 578, 583H, 583K, 583R, 583T, 587R, 587T, 589, 594H, 630B, 631D, 631E, 631G, 637D, 637E, 637G, 641B, 651...
10 FT, 10B, 117, 118, 119, 120, 120B, 127, 129, 12E, 12F, 140, 140B, 141, 14E, 153, 16, 163, 172, 183, 184, 191, 227, 24, 25, 30, 3508, 3512, 3516, 44, 46, 515, 525, 525B, 525C, 535B, 535C, 545, 545C,...
16, 315D L, 316E L, 318D2 L, 318E L, 319D L, 319D LN, 320D, 320D GC, 320D L, 320D LRR, 320D RR, 320D2, 320E, 320E L, 320E LN, 320E LRR, 321D LCR, 323D L, 323D LN, 323D SA, 323E L, 324D, 324D L, 324E, ...
6D6491
PIN
16
16
4D7839
PIN
16
16
4D7824
PIN
16
16
4D7912
PIN
16
16
4D7789
PIN
16
16
14E
14E
14E
16
4D7909
PIN
16
16
4D8065
PIN
16
16