4I0465 PIN Caterpillar parts
320 L, 320B, 320B FM LL, 320B U, 320C, 320N
Rating:
Alternative (cross code) number:
CA4I0465
4I-0465
4I0465
CA4I0465
4I-0465
4I0465
Weight: 63 pounds 28 kg.
EXCAVATOR,
Related part:
4I0465
PIN-YM
3727511
CL
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$170.13
02 Feb 2024
US: FinditParts Inc
4I0465 - PIN fits Caterpillar (CAT)
BLUMAQ
BLUMAQ
$344.82
22 Jan 2024
US: Florida-Parts-Z
4I0465 - PIN for Caterpillar (CAT)
FIRST PRICE PARTS
FIRST PRICE PARTS
$172.17
11 Jan 2024
US: FinditParts Inc
4I0465 - PIN fits Caterpillar (CAT)
BLUMAQ 4I0465 - PIN fits Caterpillar (CAT)
BLUMAQ 4I0465 - PIN fits Caterpillar (CAT)
Number on catalog scheme:
3
For full view, you need register
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0820 Hydraulic Puller 1
8B-7548 Push-Puller Tool Group 1
8B-7559 Adapter 2
8B-7561 Step Plate 1
5H-1504 Hard Washer 3
9U-6600 Hand Hydraulic Pump 1
B 125-0200 Camshaft Pilot As 2
C 125-0201 Camshaft Guide As 1
D 8T-3169 Crank Assembly 1 Start By:
Remove the rocker shaft assemblies and the pushrods. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod - Remove".
It is necessary to remove the electronic control module in order to remove the camshaft from the left hand side of the engine. Refer to Disassembly and Assembly, "Electronic Control Module (Engine) - Remove and Install".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: The following procedure is for removing the camshaft from the left hand side of the engine.
Illustration 1 g01122149
Remove camshaft covers (1).
Illustration 2 g01157699
Remove cover (2) from the front housing.
Illustration 3 g01122147
Push valve lifters (3) away from the camshaft. Hold the valve lifters in position with O-ring seals.
Illustration 4 g01122151
Remove cover (4) from the flywheel housing. Remove speed/timing sensor (5) from the flywheel housing.
Illustration 5 g01122250
Remove bolt (6). Remove ring (7).
Illustration 6 g01122265
Place the three washers from Tooling (A) behind plate (9) and install bolt (6).Note: Plate (9) must be installed in order to keep camshaft drive gear (8) on the camshaft during the removal procedure. Plate (9) can be used from the right hand camshaft drive gear. If necessary, fabricate a plate that has a diameter of 76 mm (3.0 inch). The thickness of the plate must be 19.00 mm (0.750 inch) thick. Drill a hole 22.00 mm (0.875 inch) in the center of the plate.
Illustration 7 g01122324
Do not apply more than 51675 kPa (7500 psi) pressure to the hydraulic puller. The adapters are rated at 6 1/2 tons each and the hydraulic puller is rated at 17 tons at 68900 kPa (10000 psi). If too much pressure is applied, the gear may be damaged.
Install Tooling (A) on camshaft drive gear (8). Apply 51675 kPa (7500 psi) to the puller. Strike the screw on the puller with a hammer until camshaft drive gear (8) is free from the camshaft. Remove Tooling (A) from the camshaft drive gear. Remove the camshaft drive gear from the camshaft.
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0820 Hydraulic Puller 1
8B-7548 Push-Puller Tool Group 1
8B-7559 Adapter 2
8B-7561 Step Plate 1
5H-1504 Hard Washer 3
9U-6600 Hand Hydraulic Pump 1
B 125-0200 Camshaft Pilot As 2
C 125-0201 Camshaft Guide As 1
D 8T-3169 Crank Assembly 1 Start By:
Remove the rocker shaft assemblies and the pushrods. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod - Remove".
It is necessary to remove the electronic control module in order to remove the camshaft from the left hand side of the engine. Refer to Disassembly and Assembly, "Electronic Control Module (Engine) - Remove and Install".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: The following procedure is for removing the camshaft from the left hand side of the engine.
Illustration 1 g01122149
Remove camshaft covers (1).
Illustration 2 g01157699
Remove cover (2) from the front housing.
Illustration 3 g01122147
Push valve lifters (3) away from the camshaft. Hold the valve lifters in position with O-ring seals.
Illustration 4 g01122151
Remove cover (4) from the flywheel housing. Remove speed/timing sensor (5) from the flywheel housing.
Illustration 5 g01122250
Remove bolt (6). Remove ring (7).
Illustration 6 g01122265
Place the three washers from Tooling (A) behind plate (9) and install bolt (6).Note: Plate (9) must be installed in order to keep camshaft drive gear (8) on the camshaft during the removal procedure. Plate (9) can be used from the right hand camshaft drive gear. If necessary, fabricate a plate that has a diameter of 76 mm (3.0 inch). The thickness of the plate must be 19.00 mm (0.750 inch) thick. Drill a hole 22.00 mm (0.875 inch) in the center of the plate.
Illustration 7 g01122324
Do not apply more than 51675 kPa (7500 psi) pressure to the hydraulic puller. The adapters are rated at 6 1/2 tons each and the hydraulic puller is rated at 17 tons at 68900 kPa (10000 psi). If too much pressure is applied, the gear may be damaged.
Install Tooling (A) on camshaft drive gear (8). Apply 51675 kPa (7500 psi) to the puller. Strike the screw on the puller with a hammer until camshaft drive gear (8) is free from the camshaft. Remove Tooling (A) from the camshaft drive gear. Remove the camshaft drive gear from the camshaft.
Caterpillar parts catalog:
Parts pin Caterpillar catalog:
320 L, 320B, 320C, 320D, 320D L, 320N, 322 L, 322B, 322B L, 322C, 322C FM, 323D L, 325, 325 L, 325B L, 325C, 325D, 330B L, 330C
320 L, 322, 322 FM L, 322 LN, 322B, 322B L, 322B LN, 322C, 322C FM, 324D, 324D FM, 324D L, 324D LN, 324E, 324E L, 324E LN, 325, 325 L, 325 LN, 325B, 325B L, 325C, 325C FM, 325C L, 325D, 325D FM, 325D ...
320B, 320C, 322B LN, 322C, 325B L, 325C, 330C, 330C L, 345B II, 345B L
320B, 320C, 320C FM, 320C L, 320D, 320D L, 320D2, 320D2 L, 320E, 320E L, 320E LN, 321C, 322B LN, 322C
320 L, 320B, 320B L, 320N, 345B, 345B L, OEMS
320B, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 321B, 321C, 321D LCR, 323D L, 3...
320B, 320C, 325C, 325C FM, 330C L, 345B II
320B, 320C, 320D, 320D FM, 320D L, 320D2, 320D2 L, 320E, 320E LN, 323D L, 323D LN, 323D SA, 323D2 L, 323E L, 325C, 325C FM, 325D, 325D FM, 325D L, 328D LCR, 329D, 329D L, 329D LN, 329E, 329E L, 329E L...
320C, 320C FM, 320C L
320C, 322C, 322C FM, 323D LN, 323D SA, 325B L, 325C, 325C FM, 325C L, 325D, 325D L, 325D MH, 329D, 329D L, 329D LN, 330C, 330C L, 330D, 330D L, 336D L, 336D LN, 336E, 345C, 345D, 349D L, OEMS
320C, 320D, 320D L, 320D LN, 320D LRR, 320D2 L, 320E LN, 320E LRR, 321C, 321D LCR, 322C, 323D L, 323D LN, 323D SA, 323D2 L, 323E L, 324D L, 325B L, 325C, 325D, 325D L, 329D L, 330D L, 336D L, 345C L, ...
320B, 320C, 320D, 322C, 325C, 325D, 330C L
320 L, 320B, 320B L, 320N, 345B, 345B L, OEMS
1540480
PIN AS
320B, 320C, 320C FM, 320D FM, 320D L
320B, 320C, 320C FM, 320D FM, 320D L
1716544
PIN AS
325B L, 330B L, M320
325B L, 330B L, M320
1725850
PIN
M320
M320
1284212
PIN AS
M320
M320
2040677
PIN
M320
M320
1512472
PIN
525B, 533, 535B, 543, 545, HA770, HA771, HA870, HA871, TK370, TK371, TK380, TK381
525B, 533, 535B, 543, 545, HA770, HA771, HA870, HA871, TK370, TK371, TK380, TK381
1488956
PIN
533, 543, 545, TK370, TK380
533, 543, 545, TK370, TK380
2047808
PIN AS
545
545
525B, 535B, 545
1604360
PIN AS
545
545
1525515
PIN AS
525B, 535B, 545
525B, 535B, 545