4I4807 PIN Caterpillar parts
330, 330 FM L, 330 L, 330B, 330B L, 330C, 330C L
Rating:
Alternative (cross code) number:
CA4I4807
4I-4807
4I4807
CA4I4807
4I-4807
4I4807
Weight: 52 pounds 23 kg.
Information:
EFFECTIVE LENGTH
546
mm
HEAD OD
85
mm
OVERALL LENGTH
614
mm
PIN OD
79.85
mm
TRANSV HOLES
Y
DETENT BALL
N
END TYPE A
CHAMFER
END TYPE B
LEAD TAPER
GROOVE
N
HAND RING
N
HEAD THICKNESS
9
KEEPER SLOT
N
LUBE OUTLETS
Y
COATING/PLATING
1E0586
THREAD SIZE MAX
M30X3.5
EXCAVATOR,
Related part:
4I4807
PIN-YM
3832139
CL
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Stevens Lake Parts One New Bucket Pin Fits CAT, Fits Caterpillar 330, 330 L, 3306, 330B L, 330B LN, 330C, 330C L, 330C LN, C-9 Models Interchangeable with 4I4807, 4I4807-A, BUN90-0049
Stevens Lake Parts One New Aftermarket Replacement Bucket Pin || This Is An Aftermarket Replacement Part Made To Meet Or Exceed OEM Specifications. || OEM Numbers Are Provided for Reference Only. Please Verify Fit Prior To Ordering. || Please Note: Some Listings Use Stock Images for Reference and May Differ from the Actual Product. || This Aftermarket Part Is Made to Meet or Exceed Manufacturer (OEM) Specifications.
Stevens Lake Parts One New Aftermarket Replacement Bucket Pin || This Is An Aftermarket Replacement Part Made To Meet Or Exceed OEM Specifications. || OEM Numbers Are Provided for Reference Only. Please Verify Fit Prior To Ordering. || Please Note: Some Listings Use Stock Images for Reference and May Differ from the Actual Product. || This Aftermarket Part Is Made to Meet or Exceed Manufacturer (OEM) Specifications.
RAParts 4I4807 Bucket Pin Fits Caterpillar Fits CAT Excavator Models C-9 330 3306 330C 330 L
Reliable Aftermarket Parts One New Aftermarket Replacement Bucket Pin Fits Caterpillar Engine Models: 3306, C-9 Also Fits Cater || OEM Numbers Are Provided for Reference Only. Please Verify Fit Prior To Ordering. || Please Note: Some Listings Use Stock Images for Reference and May Differ from the Actual Product. || This Aftermarket Part Is Made to Meet or Exceed Manufacturer (OEM) Specifications.
Reliable Aftermarket Parts One New Aftermarket Replacement Bucket Pin Fits Caterpillar Engine Models: 3306, C-9 Also Fits Cater || OEM Numbers Are Provided for Reference Only. Please Verify Fit Prior To Ordering. || Please Note: Some Listings Use Stock Images for Reference and May Differ from the Actual Product. || This Aftermarket Part Is Made to Meet or Exceed Manufacturer (OEM) Specifications.
RAParts 4I4807 Bucket Pin Fits Caterpillar Fits CAT Excavator Models C-9 330 3306 330C 330 L
Reliable Aftermarket Parts One New Aftermarket Replacement Bucket Pin Fits Caterpillar Engine Models: 3306, C-9 Also Fits Cater || OEM Numbers Are Provided for Reference Only. Please Verify Fit Prior To Ordering. || Please Note: Some Listings Use Stock Images for Reference and May Differ from the Actual Product. || This Aftermarket Part Is Made to Meet or Exceed Manufacturer (OEM) Specifications.
Reliable Aftermarket Parts One New Aftermarket Replacement Bucket Pin Fits Caterpillar Engine Models: 3306, C-9 Also Fits Cater || OEM Numbers Are Provided for Reference Only. Please Verify Fit Prior To Ordering. || Please Note: Some Listings Use Stock Images for Reference and May Differ from the Actual Product. || This Aftermarket Part Is Made to Meet or Exceed Manufacturer (OEM) Specifications.
Number on catalog scheme:
17
For full view, you need register
Compatible equipment models: 4I4807:
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
B 8T-2998 Lubricant -
C 1U-5718 Vacuum Pump 1
169-7372 Fluid Sampling Bottle -
4C-4057 Tube
7.9 mm (0.31 inch) OD -
D 4C-5552 Large Bore Brush 1
E 8T-7765 Surface Reconditioning Pad -
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Use Tooling (C) in order to remove the fuel and oil from the cylinder. Evacuate as much fuel and oil as possible from the cylinder before installing the electronic unit injector. Several evacuations may be necessary.
Use Tooling (D) in order to clean the carbon deposit from the inside of the electronic unit injector sleeve.
Use Tooling (E) in order to clean the carbon from the seat area that is inside of the electronic unit injector sleeve.
Illustration 1 g01259809
Install O-ring seals (7) on electronic unit injector (6). Lubricate the top two O-ring seals with a 50/50 mixture of clean engine oil and Tooling (B) .
Illustration 2 g01259759
When an electronic unit injector is replaced, the new electronic injector code must be programmed into the engine's personality module software by using the calibration menu on the Electronic Service Tool. If the new electronic injector code is not entered, the characteristics of the previous electronic unit injector is assumed.If it is not possible to immediately reprogram the electronic injector code into the personality module software, the engine will not be severely harmed. The new electronic injector code should be reprogrammed as quickly as possible in order to optimize engine performance.
Install electronic unit injector (6) and clamp (5) into the original location in the cylinder head.
Install spacer (4) and bolt (3). Tighten bolt (3) to a torque of 55 10 N m (41 7 lb ft).
Illustration 3 g01259747
Connect harness assembly (2) .
Install valve bridges (1) .Note: Make sure that the slotted end of the valve bridges are positioned toward the rocker arm shaft.
Remove the air from the fuel system. Refer to Testing and Adjusting, "Fuel System - Prime".End By: Install the rocker arms and the rocker arm shaft.
Table 1
Required Tools
Tool Part Number Part Description Qty
B 8T-2998 Lubricant -
C 1U-5718 Vacuum Pump 1
169-7372 Fluid Sampling Bottle -
4C-4057 Tube
7.9 mm (0.31 inch) OD -
D 4C-5552 Large Bore Brush 1
E 8T-7765 Surface Reconditioning Pad -
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Use Tooling (C) in order to remove the fuel and oil from the cylinder. Evacuate as much fuel and oil as possible from the cylinder before installing the electronic unit injector. Several evacuations may be necessary.
Use Tooling (D) in order to clean the carbon deposit from the inside of the electronic unit injector sleeve.
Use Tooling (E) in order to clean the carbon from the seat area that is inside of the electronic unit injector sleeve.
Illustration 1 g01259809
Install O-ring seals (7) on electronic unit injector (6). Lubricate the top two O-ring seals with a 50/50 mixture of clean engine oil and Tooling (B) .
Illustration 2 g01259759
When an electronic unit injector is replaced, the new electronic injector code must be programmed into the engine's personality module software by using the calibration menu on the Electronic Service Tool. If the new electronic injector code is not entered, the characteristics of the previous electronic unit injector is assumed.If it is not possible to immediately reprogram the electronic injector code into the personality module software, the engine will not be severely harmed. The new electronic injector code should be reprogrammed as quickly as possible in order to optimize engine performance.
Install electronic unit injector (6) and clamp (5) into the original location in the cylinder head.
Install spacer (4) and bolt (3). Tighten bolt (3) to a torque of 55 10 N m (41 7 lb ft).
Illustration 3 g01259747
Connect harness assembly (2) .
Install valve bridges (1) .Note: Make sure that the slotted end of the valve bridges are positioned toward the rocker arm shaft.
Remove the air from the fuel system. Refer to Testing and Adjusting, "Fuel System - Prime".End By: Install the rocker arms and the rocker arm shaft.
Caterpillar parts catalog:
Parts pin Caterpillar catalog:
330, 330 FM L, 330 L, 330B, 330B L, W330B
330, 330 FM L, 330 L, 330B, 330B L, 345B, 345B L, W330B
330, 330 FM L, 330 L, 330B, 330B L
325B L, 330, 330 FM L, 330 L, 330B, 330B L, 345B II, 345B II MH, W330B, W345B II
325B L, 330, 330 FM L, 330B L
330, 330 FM L, 330 L, 330B, 330B L
330B L, 330C, 330C L
330B L, 330C, 330C L
330 FM L, 330 L, 330B, 330B L, 330C L
330 FM L, 330 L, 330B, 330B L, 330C L
325C, 325D L, 330C, 330D L, 345B II, 345C L, 365B, 365B II, 365C, 365C L, 385B, 385C L
330C, 330C L
330, 330 FM L, 330 L, 330B, 330B L
1156293
PIN
330
330
1156294
PIN
330
330
325B L, 330, 330 FM L, 330B L
325B L, 330, 330 FM L, 330 L, 330B, 330B L, 345B II, 345B II MH, W330B, W345B II
330, 330 FM L, 330 L, 330B, 330B L
6C6026
PIN AS
325 LN, 325B L
325 LN, 325B L
1913180
PIN AS
330B, 330B L, 330C L, 330D L, 330D LN, 336D L, 336D2 L
330B, 330B L, 330C L, 330D L, 330D LN, 336D L, 336D2 L
2054667
PIN
325B L, 325C, 325C L, 325D L, 325D MH, M325B, M325C MH, M325D L MH, M325D MH
325B L, 325C, 325C L, 325D L, 325D MH, M325B, M325C MH, M325D L MH, M325D MH
2054338
PIN AS
325B L, 325C, 325C L, 325D MH, M325B
325B L, 325C, 325C L, 325D MH, M325B
1308818
PIN
325B L, 325C FM, 325D FM, 325D FM LL, M325B, M325C MH, M325D L MH
325B L, 325C FM, 325D FM, 325D FM LL, M325B, M325C MH, M325D L MH
325B, 325B L, M325B