6J5985 PIN Caterpillar parts
814S, 824S, 854G, 854K, D10N, D10R, D10T, D10T2, D11N, D11R, D11T
Rating:
Alternative (cross code) number:
CA6J5985
6J-5985
6J5985
CA6J5985
6J-5985
6J5985
Weight: 8 pounds 3 kg.
BULLDOZER, WHEEL DOZER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
08 Dec 2017
862 Hundredths Pounds
CTP: CTP
Caterpillar PIN (6J5985)
6J5985 Weight(lbs): 8.60 Length(cm): 8.0000 Width(cm): 8.0000 Depth(cm): 24.0000
6J5985 Weight(lbs): 8.60 Length(cm): 8.0000 Width(cm): 8.0000 Depth(cm): 24.0000
Compatible equipment models: 6J5985:
Information:
Turbocharged Engines and Turbocharged Aftercooled Engines
Illustration 1 g01345407
A cross section of a cylinder head for a turbocharged engine and turbocharged aftercooled engines
(1) Valve springThe installed length of the valve springs ... 36.17 mm (1.4240 inch)The load for the installed valve spring ... 312 N (70 lb) (2) Valve spring recess (3) The finished valve guidesInside diameter of valve guide ... 9.000 to 9.022 mm (0.3543 to 0.3552 inch)Outside diameter of the valve guide ... 13.034 to 13.047 mm (0.5131 to 0.5137 inch)Interference fit of valve guide in cylinder head ... 0.007 to 0.047 mm (0.0003 to 0.0019 inch)Length of Valve guide ... 51.00 to 51.50 mm (2.018 to 2.027 inch)Projection of the valve guide above the valve spring recess (2) ... 12.35 to 12.65 mm (0.486 to 0.498 inch)Note: When new valve guides are installed, new valves and new valve seat inserts must be installed. The valve guides and the valve seat inserts are supplied as partially finished parts. The unfinished valve guides and unfinished valve seat inserts are installed in the cylinder head. The guides and inserts are then cut and reamed in one operation with special tooling. This procedure ensures the concentricity of the valve seat to the valve guide to create a seal that is tight. Refer to Disassembly and Assembly for removal and installation procedures. (4) Exhaust valveDiameter of the exhaust valve stem ... 8.938 to 8.960 mm (0.3519 to 0.3528 inch)Clearance of valve in valve guide ... 0.040 to 0.062 mm (0.0016 to 0.0024 inch)Overall length of the exhaust valve ... 128.184 to 128.634 mm (5.0466 to 5.0643 inch)The face of the exhaust valve is recessed below the cylinder head by the following amount.Turbocharged engines and turbocharged aftercooled engines ... 1.55 to 1.81 mm (0.0610 to 0.0713 inch)Service limit ... 2.06 mm (0.0811 inch) (5) Inlet valveDiameter of the inlet valve stem ... 8.953 to 8.975 mm (0.3525 to 0.3533 inch)Clearance of valve in valve guide ... 0.025 to 0.069 mm (0.001 to 0.0027 inch)Overall length of the inlet valve ... 128.838 to 129.288 mm (5.0724 to 5.0901 inch)The face of the inlet valve is recessed below the cylinder head by the following amount.Turbocharged engines and turbocharged aftercooled engines ... 1.60 to 1.85 mm (0.0630 to 0.0728 inch)Service limit ... 2.09 mm (0.0823 inch) (6) Exhaust valve face angle from the horizontal axisValve face angle ... 30 degreesValve seat angle ... 30 degrees (7) Diameter of the exhaust valve head ... 41.51 to 41.75 mm (1.634 to 1.643 inch) (8) Diameter of the head of the inlet valve ... 46.20 to 46.45 mm (1.8189 to 1.8287 inch) (9) Angle of the inlet valve face from the horizontal axisValve face angle ... 30 degreesValve seat angle ... 30 degreesThe valve lash is the following value when the engine is cold:Inlet valves ... 0.20 mm (0.008 inch)Exhaust valves ... 0.45 mm (0.018 inch)
Illustration 2 g00809016
Recess for the valve seat insert
(10) Machine the recess in the head for valve seat inserts to the following dimensions.Recess for inlet
Illustration 1 g01345407
A cross section of a cylinder head for a turbocharged engine and turbocharged aftercooled engines
(1) Valve springThe installed length of the valve springs ... 36.17 mm (1.4240 inch)The load for the installed valve spring ... 312 N (70 lb) (2) Valve spring recess (3) The finished valve guidesInside diameter of valve guide ... 9.000 to 9.022 mm (0.3543 to 0.3552 inch)Outside diameter of the valve guide ... 13.034 to 13.047 mm (0.5131 to 0.5137 inch)Interference fit of valve guide in cylinder head ... 0.007 to 0.047 mm (0.0003 to 0.0019 inch)Length of Valve guide ... 51.00 to 51.50 mm (2.018 to 2.027 inch)Projection of the valve guide above the valve spring recess (2) ... 12.35 to 12.65 mm (0.486 to 0.498 inch)Note: When new valve guides are installed, new valves and new valve seat inserts must be installed. The valve guides and the valve seat inserts are supplied as partially finished parts. The unfinished valve guides and unfinished valve seat inserts are installed in the cylinder head. The guides and inserts are then cut and reamed in one operation with special tooling. This procedure ensures the concentricity of the valve seat to the valve guide to create a seal that is tight. Refer to Disassembly and Assembly for removal and installation procedures. (4) Exhaust valveDiameter of the exhaust valve stem ... 8.938 to 8.960 mm (0.3519 to 0.3528 inch)Clearance of valve in valve guide ... 0.040 to 0.062 mm (0.0016 to 0.0024 inch)Overall length of the exhaust valve ... 128.184 to 128.634 mm (5.0466 to 5.0643 inch)The face of the exhaust valve is recessed below the cylinder head by the following amount.Turbocharged engines and turbocharged aftercooled engines ... 1.55 to 1.81 mm (0.0610 to 0.0713 inch)Service limit ... 2.06 mm (0.0811 inch) (5) Inlet valveDiameter of the inlet valve stem ... 8.953 to 8.975 mm (0.3525 to 0.3533 inch)Clearance of valve in valve guide ... 0.025 to 0.069 mm (0.001 to 0.0027 inch)Overall length of the inlet valve ... 128.838 to 129.288 mm (5.0724 to 5.0901 inch)The face of the inlet valve is recessed below the cylinder head by the following amount.Turbocharged engines and turbocharged aftercooled engines ... 1.60 to 1.85 mm (0.0630 to 0.0728 inch)Service limit ... 2.09 mm (0.0823 inch) (6) Exhaust valve face angle from the horizontal axisValve face angle ... 30 degreesValve seat angle ... 30 degrees (7) Diameter of the exhaust valve head ... 41.51 to 41.75 mm (1.634 to 1.643 inch) (8) Diameter of the head of the inlet valve ... 46.20 to 46.45 mm (1.8189 to 1.8287 inch) (9) Angle of the inlet valve face from the horizontal axisValve face angle ... 30 degreesValve seat angle ... 30 degreesThe valve lash is the following value when the engine is cold:Inlet valves ... 0.20 mm (0.008 inch)Exhaust valves ... 0.45 mm (0.018 inch)
Illustration 2 g00809016
Recess for the valve seat insert
(10) Machine the recess in the head for valve seat inserts to the following dimensions.Recess for inlet
Cat SIS web machinery list:
Parts pin Caterpillar catalog:
3G0500
PIN AS
10, D10, D10N, D11N, D9L, E650
10, D10, D10N, D11N, D9L, E650
9W7007
PIN
D10N, D10R
D10N, D10R
8P9382
PIN
D10N, D10R, D9L
D10N, D10R, D9L
9J6662
PIN
D10N, D10R, D10T, D10T2, D9L
D10N, D10R, D10T, D10T2, D9L
3G8053
PIN
D10N, D10R, D10T, D10T2, D9L
D10N, D10R, D10T, D10T2, D9L
7T4810
PIN
D10N, D10R, D10T, D10T2
D10N, D10R, D10T, D10T2
7T7222
PIN AS
D10N, D10R, D10T, D10T2, D9L
D10N, D10R, D10T, D10T2, D9L
1112106
PIN AS
D10N, D10R, D10T, D10T2
D10N, D10R, D10T, D10T2
7T7303
PIN AS
D10N, D10R, D10T, D10T2
D10N, D10R, D10T, D10T2
1279189
PIN
D10R, D11R, D11T
D10R, D11R, D11T
1303434
PIN
D11R, D11T
D11R, D11T
1305355
PIN AS
D11R, D11T
D11R, D11T
9W2939
PIN
854G, 854K, D10N, D10R, D10T, D10T2, D11N, D11R, D11T
854G, 854K, D10N, D10R, D10T, D10T2, D11N, D11R, D11T
9J2364
PIN
10S, 854G, 854K, D10, D11N, D11R
10S, 854G, 854K, D10, D11N, D11R
9J2366
PIN
10S, 854G, 854K, D10, D11N, D11R, D11T
10S, 854G, 854K, D10, D11N, D11R, D11T
7T9311
PIN AS-CARTRIDGE
D10, D11N, D11R, D11T
D10, D11N, D11R, D11T
6Y1581
PIN-TRACK
D11N
D11N
3T7792
PIN
D11N, D11R, D11T
D11N, D11R, D11T
3G0500
PIN AS
10, D10, D10N, D11N, D9L, E650
10, D10, D10N, D11N, D9L, E650
8E4651
PIN
D10N, D11N
D10N, D11N
4T3535
PIN AS
D10, D11N, D11R
D10, D11N, D11R
9J6691
PIN AS
D10R, D11N, D9L
D10R, D11N, D9L
9J3226
PIN AS
10, D10, D11N, D11R
10, D10, D11N, D11R
9J2593
PIN
10S, 854G, 854K, D10, D11N, D11R, D11T
10S, 854G, 854K, D10, D11N, D11R, D11T