PIN 6K0414 - Caterpillar

In the following examples, the symbol "<-" indicates messages that are sent by the host device. The symbol "->" indicates messages that are sent by the CCM. The first two examples show the programming of broadcast messages. The third example activates the diagnostic codes.Note: The values in these examples are hexadecimal.G3600 ESS Programming Examples
Message 1
This example will obtain the following information from a G3600 ESS system.
Engine Speed
Engine Timing
Fuel Position
Data will be sent in 0.5 second intervals from the CCM to the host equipment.
Data will be separated by commas.
Program the following message: <-50001315011301000000400041F111 00000000000000000000cs ->506115021300cs
Activate the message: <-5000110101cs ->506115021100cs Message 2
This example will obtain the following information from a G3600 ESS system.
Fuel Flow
Air Flow
BTU reading
Air Temperature
Data will be sent in one second intervals from the CCM to the host device.
Data will not have any separators.
Program the following message: <-500013150213020020F518F51EF51AF511 0000000000000000cs ->506115021300cs
Activate the message: <-5000110102cs ->506115021100cs Message 3
This example will obtain the diagnostic codes from the G3600 ESS system in 5 second intervals.
Send the following message: <-50008203130100cs ->506115028200cs
The messages will come from the CCM in the following format. ->5061100C0113,ddd1,ddd2,ddd3,cs ->5061100C0113,ddd1,ddd2,ddd3,cs ->5061100A0213ddd1ddd2ddd3ddd4cs ->5061100C0113,ddd1,ddd2,ddd3,cs ->5061100C0113,ddd1,ddd2,ddd3,cs ->5061100A0213ddd1ddd2ddd3ddd4cs ->5061100C0113,ddd1,ddd2,ddd3,cs ->5061100C0113,ddd1,ddd2,ddd3,cs ->5061100A0213ddd1ddd2ddd3ddd4cs ->5061100C0113,ddd1,ddd2,ddd3,cs ->5061100C0113,ddd1,ddd2,ddd3,cs ->5061100A0213ddd1ddd2ddd3ddd4cs ->5061100C0113,ddd1,ddd2,ddd3,cs ->5061100C0113,ddd1,ddd2,ddd3,cs ->5061100A0213ddd1ddd2ddd3ddd4cs ->5061100C0113,ddd1,ddd2,ddd3,cs ->5061100C0113,ddd1,ddd2,ddd3,cs ->5061100A0213ddd1ddd2ddd3ddd4cs ->5061820301F40Ccs This pattern will then repeat. Shutting Off The Messages
To turn off the messages, the following messages must be sent. The messages can be sent at any time.Turn OFF Message 1 <-5000120101cs ->506115021200csTurn OFF Message 2 <-5000120102cs ->506115021200csTurn OFF Message 3 (diagnostic codes) <-50008203130180cs ->506115028200csDiagnostic Codes - Retrieve
The CCM allows the diagnostic codes to be read from the CCM and the Gas Engine Controller. This is accomplished by using IID 82 or IID 24. Requesting Diagnostic Codes for the CCM
Use IID 24 with PID 0082 to retrieve the codes for the CCM. The format for the message is given below.5000240400610082csThe CCM responds with two data bytes. Each E code on the display represents a bit in the two bytes of data. Refer to Operation and Maintenance Manual, SEBU7014, "Diagnostic Code - Troubleshoot" in this manual.Requesting Diagnostic Codes for the G3600
The diagnostic codes for the G3600 can be retrieved by using IID 82 or IID 24 with PID 0082. The diagnostic codes will be sent on the RS-232C link at the specified time when IID 82 is used. Refer to the IID 82 description in Operation and Maintenance Manual, "Communication Protocol for Customized Systems" in this manual. The format for the IID 82 message is given below.50008203130100csThe diagnostic codes will be sent in five second intervals. The second method uses IID 24 with PID 0082. The diagnostic codes will be displayed once every time the message is sent. The format for the IID 24 message is given below:5000240400130082csRefer to the PID 0082 format in Operation and Maintenance Manual, SEBU7014, "Parameter Identifiers for G3600 Engines" and the IID 24 format in Operation and Maintenance Manual, SEBU7014, "Instruction Identifiers".Requesting Diagnostic Codes for the G3500 Air/Fuel Ratio
The diagnostic codes for the G3500 Air/Fuel Ratio can be retrieved by using IID 82. The diagnostic codes for the G3500 Air/Fuel